Teledyne PEM 9002 User manual

PE Mortable missions onitor
PEM 9002
(US - Version, V1.0)

16830 Chestnut Street City of Industry,
California 91748, USA
TEL: [phone]
TOLL FREE: 888-789-8168
FAX: [phone]
www.teledyne-ai.com

WARRANTY SUMMARY
Teledyne warrants that the products it manufactures will be free from defects
in materials and workmanship for a period of one year from the date of delivery
from factory.
If a product proves defective within the respective period, Teledyne will provide
repair or replacement as described in the complete warranty statement.
To arrange for service or obtain a copy of the complete warranty statement,
please contact your nearst Teledyne distributor.
EXCEPT AS PROVIDED IN THIS SUMMARY OR THE APPLICABLE
WARRANTY STATEMENT, TELEDYNE MAKES NO WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED,INCLUDING WITHOUT LIMITA-
TION THE IMPLIED WARRANTIES OR MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
TELEDYNE BE LIABLE FOR INDIRECT, SPECIAL OR CONSEQUEN-
TIAL DAMAGES.

Table of Contents
Page
1 Product Description............................... .2
2 Physical Data..........................................5
2.1 Calculation Formulae ............................. 6
3 Technical Data ........................................7
4 Front Panel Overview ...........................10
5 Keypad Functions .................................11
6 User Guide ...........................................12
6.1 Program Start Menu ..............................12
6.2 Calibration Menu ...................................13
6.3 Fuel Selection .......................................14
6.4 Additional Functions/Meas. Program....15
6.5 Draft Measurement ...............................16
6.6 Menu Lines............................................17
6.6.1 Menu Line 1...........................................18
6.6.1.1 Menu - Info Box.....................................19
6.6.1.2 Menu - Time and Date...........................20
6.6.2 Menu Line 2...........................................21
6.6.2.1 Menu - .....................................21
Page
6.6.2.2 Menu - Core Of Waste Gas Flow ..........22
6.6.2.3 CO Purge System ( )........22
6.6.3 Menu Line 3 ..........................................23
6.6.3.1 Menu - Units ..........................................23
6.6.3.2 Menu - O2-Ref.......................................23
6.6.3.3 Menu - Add. Data...................................24
6.6.4 Menu Line 4 .........................................25
6.6.4.1 Memory Functions.................................25
6.6.4.2 Menu - Create memory blocks ...............29
6.6.4.3 Menu - Delete memory data...................32
6.6.4.4 Printing the Measured Values ................34
6.7 Configuration Menu ..............................35
6.8 Entering the Company Address ............37
7 System Maintenance ............................38
8 RS 232 Interface ...................................39
9 Battery / Line Power Operation..............39
10 Loading Paper ......................................42
11 Waste Gas Cleaning System .................43
11.1 Filters And Other Cleaner Parts......
Graphic
Menu -
........44
manual
1

2
1. Product Description
The Gas Analysis Computer is a multiple -function analyzer with integrated calculating functions.
Measurements are in accordance with the general regulations set forth by the BIMSchV (German
Regulations concerning the protection against harmful effects on the environment) at all kinds of
combustion plants within the framework of the monitoring of exhaust systems.
for monitoring exhaust systems and for determining
the efficiency of combustion plants:
Measured Values: T.Gas Waste or flue gas temperature °F or °C
T.Room Air or ambient temperature
Oxygen content % Volume
CO Carbon monoxide ppm - mg/m³ - mg/kWh
NO Nitrogen monoxide (Option) ppm - mg/m³ - mg/kWh
Draft Draft or inches of H O (iWC)
Calculated Values: Carbon dioxide % Volume
CO 0% Carbon monoxide, undiluted ppm
Effi. Combustion efficiency %
Ex.air Excess air value
Losses Waste gas losses %
NOx Nitrogen oxides (optional) ppm - mg/m³ - mg/kWh
T.Diff Differential temperature (TG-TA)
a) Measurement and calculation parameters
°F or °C
Sulphur dioxide (Option) ppm - mg/m³ - mg/kWh
Pressure
°F or °C
O2
CO2
SO2
2

b) Measuring Procedure
Temperature Measurem.: K-type thermocouple ( ) for waste or flue gas temperature
for air or ambient temperature.
O2-Measurement : Electrochemical measuring cell.
CO-Measurement : Electrochemical measuring cell.
Draft Measurement : Piezo-resistive principle with internal temperature compensation.
Measuring Duration: Short-term memory measurements of max. 60 minutes are possible, followed by
a new calibration phase with ambient air.
Waste Gas Measurement : Via an external water separator and filter, the waste gas is fed to the sensors by
means of a gas feed pump. The pump capacity during the feeding phase is
approx. 0.8 l/min.
Sensor Calibration: 60 seconds after switching on the instrument.
CO Concentration: CO sensor with H compensation, measuring range 0 - 4.000 ppm. Cutoff
threshold at 4.000 ppm for sensor protection via separate flush pump.
The remaining measuring values are not affected. The instrument is switched on
again at a value of 1.600 ppm.
Waste Gas Sampling: By means of a waste gas sampling probe with retainer cone.
NiCr-Ni
K-type thermocouple (NiCr-Ni)
2
3

c) Instrument Description
Electrical Supply: NiCad battery 6V/4.0 Ah, external charger.
Display: With backlight; alphanumeric and graphic display.
4 lines of 16 characters each, plus menu line.
Computer Interface: RS 232.
Printer Interface: Pin Printer (Normal Paper).
Printer: External infrared thermo-paper printer.
Memory: 100 memory blocks
Adm. Operating Temp.: + 40 °F to + 104 °F (+ 5°C to + 40°C).
Adm. Storage Temp.: -22 °F to + 140 °F (- 30°C to + 50 °C).
Mech. Dimensions: 10.6” x 9.6” x 6.9” (270 x 245 x 175 mm).
Weight: 8.0 lbs (3,8 kg).
Standard Version: Instrument, battery charger, combined flue gas temperature
probe / watertrap and hose assembly with measuring cone,
ambient air temperature sensor, carrying case and manual.
4

2. Physical Data
Measuring ranges: CO 0 ... 4.000 ppm
CO-0% 0 ... 9.999 ppm
0 ... 20,9 % Volume
T.Gas + 32 °F to + 1.850 °F (0 °C ... + 1.000 °C)
T.Room -5 °F to + 212 °F (- 20 °C ... +100 °C)
Draft/Pressure ( 150.0 hPa)
C 0,0 ... CO % Volume
Losses 0 ... 100%
Efficiency 100 ... 0%
Excess air 1 ... 99.999.
Optional: NOx, NO 0 ... 2.000 ppm
SO NO 0 ... 2.000 ppm
CO High 0 ... 1.0 % Volume (10.000 ppm)
(General Specifications)
O2
60 inches of H O
O2 2 max
2,
±±
2
5