Tennant S30 XP Training manual

IB 340883 (02--2008) 1
INSTRUCTION BULLETIN
No. 340883
Machine: S30 XP / X4
Published: 02--2008
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9004325
SYNOPSIS:
This kit contains the parts needed to replace the instrument panel label on S30 XP and S30 X4
machines.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1 hour)
PREPARATION:
1. Park machine on a clean level surface, turn off
machine, remove key, and set parking brake.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, set parking
brake, turn off machine, and remove key.
2. Disconnect the negative terminal from the
battery.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.
3. Remove the hardware holding the panel
assembly to the dash. Discard the hardware.
Refer to Fig. 1.
FIG. 1
4. Carefully lift the panel assembly from the
dash and disconnect the main wire harness
from the panel assembly. Refer to Fig. 2.
FIG. 2
5. Set the panel assembly face down on a clean
flat surface.

IB 340883 (02--2008)2
INSTALLATION:
NOTE:Connect one end of the ground strap (4) to
ground and wrap the other end around wrist
before handling the control panel / instrument
panel label (1). The ground strap must be worn
whenever the control panel / new instrument
panel label are being handled.
1. Remove the back cover from the control
panel. Set the back cover and hardware
aside. Refer to Fig. 3.
FIG. 3
2. Remove the five fasteners and six standoffs
holding the circuit board to the panel
assembly. Set the fasteners, standoffs, and
eleven nylon washers aside. Refer to Fig. 4.
FIG. 4
3. Remove the circuit board from the instrument
panel and set the circuit board on a clean flat
surface. Refer to Fig. 5.
FIG. 5
4. Remove the eleven aluminum spacers from
the instrument panel label. Set the spacers
aside. Discard the instrument panel label.
Refer to Fig. 6.
FIG. 6
5. Place the eleven aluminum spacers onto the
new instrument panel label (1). Refer to Fig. 6.
NOTE:All aluminum spacers must be installed
onto the instrument panel label (1). Board could
be damaged if any standoffs are missing.
6. Use the hardware from Step 2 to install the
circuit board onto the instrument panel label
(1). Refer to Fig. 4.

IB 340883 (02--2008) 3
7. Reinstall the back cover plate onto the control
panel assembly. Refer to Fig. 3.
8. Reconnect the main wire harness to the panel
assembly. Refer to Fig. 2.
9. Use the five pan screws (2) and five nylon
washers (3) to reinstall the panel assembly
onto the dash. Refer to Fig. 1.
10. Reconnect the negative terminal to the
battery.
11. Start and test the machine. Verify the
machine operates properly.
Bill of Materials for Panel Kit, Label, Replmt [S30] -- 9004325
Ref.
Tennant
Part No. Description Qty.
o9004325 )Panel Kit, Label, Replmt [S30] 1
Y1 1045321 Panel Assy, Instrmt, w/Label, Replmt 1
Y2 1045487 Screw, Pan, Phl, M5 X 0.80 X 16, Blk 5
Y3 1012615 Washer, Flat, 0.19B 0.44D .03, Nyl, Blk 5
Y427964 Strap, Ground, Static, Disposable 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452