Teral CMF3-HOH User manual

Create future with water and air
Centrifugal Fan
Mild Fan
Model CMF3-HOH
Instruction Manual
TERAL INC.
Ensure that copies of this manual are supplied to the all those who
operate, maintain or inspect this device.
Do not operate, maintain or inspect this device until you have read and
understood this manual.
Keep this manual in a safe place where it can be referred to at any time.

䎪䏒䏙䏈䏕䏑䏐䏈䏑䏗䏄䏏

䎷䏄䏅䏏䏈䎃䏒䏉䎃䎦䏒䏑䏗䏈䏑䏗䏖
䏗䏋䏈

䎔
䎔

䏌
䎷䏈䏕䏄䏏䎊䏖

㧞㧚Fan structure and overview
㧞㧚1Structure and component names
Number
㪈
㪉
㪊
㪋
㪌
㪍Intake flange
Motor Stand
Motor
Part Name
Casing
Impeller
A
ir intake
㧞㧙㧝

䏈䏏䏈䏆䏗䏕䏌䏆
䏒䏘䏗䏇䏒䏒䏕
䏇䎏
䏈䎏

䏒
䎏

䏌䏖
䏎䎺
䎔䎔䏎䎺䱊䎕䎕䏎䎺
䏎䎺

䏄䏑
䏄䏑
䏐䏄䏎䏈䏖
䏖
䏓䏋䏈䏑䏒䏐䏈䏑䏒䏑

䏑
䏌䏐䏓䏈䏏䏏䏈䏕

䏐䏌䏑
䎐䎔
䎐䎔
䏐䏌䏑

㧤㧚
Motor bearing replacement procedure 㧔㧯㧹㧲㧟㧙㧺㨛㧚㧟 1/2㨪㧢㧙㧴㧻㧴㧙㧿㧕
1. Necessary tools
(a) Spanner (M10 and M12)
(b) Pulley remover
(c) Impeller remover (special tool)
2. Disassembly procedure
Table 1 Parts list
No. Part name
1 Casing
2 Impeller
3 Impeller hub
4 Impeller washer
5 Impeller bolt
6 Impeller key
7 Inlet
8 Motor plate
9 Motor
Fig. 1 Fan diagram
1) Before disassembling the fan, make any markings which will be necessary when
reassembling it.
2) Remove the inlet external connection.
3) Remove the foundation bolt.
4) Move the fan so that the inlet can be removed.
5) Remove the inlet.
6) Remove the impeller from the motor.
(1)Turn the impeller bolt counterclockwise, and remove it with the washer
from the center of the impeller (end of the main shaft).
(2)Either suspend or support the impeller so that it will not fall.
(3)Use the screw holes which are located at either side of the shaft hole at
the end of the impeller boss to attach the impeller remover as shown in
Fig. 2, tighten the remover bolt and remove the impeller.
The impeller can be removed more easily if a hydraulic device is used.
If it is difficult to remove the impeller, either apply some penetrating oil
between the impeller boss and main shaft or heat the boss to about 100
to 120°C. However, be careful not to heat the main shaft.
Do not hit the impeller with a hammer or remove it at an angle as this
may lead to the main shaft being bent.
8-1