Terex BID-WELL 2450 User manual

SERIAL NO.
When ordering parts or when consulting the
Terex Bid-Well Service Department
ALWAYS KNOW your MACHINE SERIAL NUMBER
CANTON, SD 57013
 TEL:605-987-2603•FAX:605-987-2605
2450CARRIAGEFOGGER(1/2012)  PAGE1.1
2450 Carriage Fogger

WARRANTY
2450CARRIAGEFOGGERSYSTEM
The Terex Bid-Well products are warranted, to the original owner,
against defects in workmanship and materials for a period of
1 year from delivery date. This warranty is limited to repair or
replacement of those parts found defective in material or work-
manship. All parts such as hydraulic and mechanical compo-
nents not made by Terex Bid-Well are warranted to the extent of
the original manufacturer’s warranty. Engines are not warranted
by Terex Bid-Well but are warranted by the engine manufacturer.
See the engine Owner’s Manual.
Terex Bid-Well shall have no liability for loss of use or for any
incidental or consequential damages, such as, but not limited
to, loss of profits, loss of use of other equipment, improper
performance of work, penalties of any kind, loss of services of
personnel, or any other losses which may be experienced by
the Buyer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EX-
PRESSED OR IMPLIED (INCLUDING THOSE OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE), AND
ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART.
TEREX BID-WELL NEITHER ASSUMES NOR AUTHORIZES
ANY OTHER PERSON TO ASSUME FOR TEREX BID-WELL, ANY
OTHER LIABILITY IN CONNECTION WITH THE SALE OF TEREX
BID-WELL PRODUCTS. THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
PAGE1.2  2450CARRIAGEFOGGER(1/2012)

INTRODUCTION
This manual has been compiled to assist the owner/
operator with the correct setup, operation and routine
maintenance needed for the safe and efficient use of
the Terex Bid-Well Paver. In order to maximize the
performance and efficiency of the Paver it is VERY
IMPORTANT that the owner/operator and maintenance
personnel read this manual thoroughly before operat-
ing or servicing the machine. You should have a basic
knowledge about the handling of concrete products and
should be trained and licensed per state requirements
before operating this equipment. Always keep this
manual in a convenient place for instant reference and
never attempt to make repairs or adjustments that you
do not fully understand. If you require any additional
information or service do not hesitate to call the Terex
Bid-Well Service Department. (Tel: [phone] - Fax:
605-987-2605)
OPERATORQUALIFICATION
Operation shall be limited to personnel with the follow-
ing minimum qualifications:
1. Designated persons.
2. Trainees under the direct supervision of a desig-
nated person.
3. Maintenance and test personnel (when it is neces-
sary in the performance of their duties).
Operators shall be required by the employer to pass a
practical operating examination. Qualifications shall
be limited to the specific type of equipment for which
examined.
Operators and operator trainees shall meet the follow-
ing physical qualifications:
1. Vision of at least 20/30 Snellen in one eye and
20/50 in the other, with or without corrective
lenses.
2. Ability to distinguish colors, regardless of position,
if color differentiation is required for operation.
3. Adequate hearing, with or without hearing aid, for
the specific operation.
Evidence of physical defects or emotional instability
which could render a hazard to the operator or others, or
which in the opinion of the examiner could interfere with
the operator’s performance, may be sufficient cause for
disqualification. In such cases, specialized clinical or
medical judgements and tests may be required.
Evidence that an operator is subject to seizures or loss
of physical control shall be sufficient reason for disquali-
fication. Specialized medical tests may be required to
determine these conditions.
Operators and operator trainees should have normal
depth perception, field of vision, reaction time, manual
dexterity, coordination and no tendencies to dizziness
or similar characteristics.
In addition to the above listed requirements, the opera-
tor shall:
1. Demonstrate the ability to comprehend and in-
terpret all labels, operator manuals, safety codes
and other information pertinent to the operation
of the paver.
2. Possess knowledge of emergency procedures and
implementation of same.
3. Demonstrate to the employer the ability to operate
the specific equipment.
4. Be familiar with applicable safety regulations.
5. Understand responsibility for maintenance require-
ments.
6. Understand the operating procedures as outlined
by the manufacturer.
OPERATORCONDUCT
1. The operator shall not engage in any practice which
will divert his/her attention while actually engaged
in operating the machine.
2. Each operator shall be responsible for those opera-
tions under the operator’s direct control. Whenever
there is any doubt as to safety, the operator shall
consult with the supervisor.
3. If there is a warning sign on a switch, engine control
or paver component, the operator shall not close
the switch, start the engine or use the component
until the warning sign has been remove or acknowl-
edged by the appointed person.
4. Before operating the paver, the operator shall see
that all controls are in the “off” or neutral position
and that all personnel are in the clear.
5. In accordance with OSHA regulations 1928.51 and
1928.52, operating instructions must be provided
initially to operators/employees before allowing
them to operate the paver and should be reviewed
annually thereafter.
The most IMPORTANT safety device on this equipment
is a well trained and safe operator. It is his/her respon-
sibility to read and understand all safety and operating
instructions in this manual. A person who has not read
and understood all operating and safety instructions is
not qualified to operate the paver. An untrained opera-
tor exposes himself/herself and bystanders to possible
injury or death. All accidents can be avoided!!!
DO NOT modify the paver in any way without consult-
ing the factory. Unauthorized modification may impair
function and/or safety and affect the working life of the
equipment.
Terex Bid-Well assumes NO LIABILITY for accidents
or injury incurred through the improper use of this
equipment.
2450CARRIAGEFOGGER(1/2012)  PAGE1.3

4. Be sure to wear safe work clothing. It should be
well fitted and in good repair. Do not wear rings,
wrist watches or loose fitting clothing when work-
ing on machinery, they could catch on moving
parts causing serious injury. Wear sturdy, rough
soled work shoes, safety glasses and any other
protective gear that is warranted by the work en-
vironment.
5. Keep work area organized and clean. Wipe up oil
spills of any kind. Keep tools and parts off floor.
Eliminate the possibility of a fall which could result
in serious injury.
6. Be sure to reinstall safety devices, guards or
shields after adjusting and/or servicing the ma-
chine.
7. After servicing, be sure that all tools, parts or ser-
vicing equipment are removed from the vehicle
or engine.
8. Do not get into a rush! Use recommended hand
holds and steps with at least three points of sup-
port when getting on and off the paver. Keep steps,
floors, hand holds and controls clean and free of
grease. Face the machine when climbing up and
down and never jump off the paver or dismount
while it is in motion.
9. Keep all personnel clear of augers, rollers and car-
riage frame when operating the paver.
10. Do not permit riders on the paver.
HYDRAULICSYSTEMSPRECAUTIONS
1. Make sure that all components are in good work-
ing condition. Replace any worn, cut, abraded,
flattened or crimped hoses andmetal lines.
2. Do not attempt makeshift repairs using tape,
clamps or cements. The hydraulic system operates
under extremely high pressure and such repairs
could cause serious injury.
3. Wear proper hand and eye protection when search-
ing for a high pressure leak. Use a piece of wood
or cardboard as a back stop instead of hands to
isolate and identify leaks.
4. If injured by concentrated high pressure steam or
hydraulic fluid, seek medical attention imediately.
Serious infections or toxic reaction can develop
from hydraulic fluid penetrating the skin.
REFUELINGPRECAUTIONS
1. When refueling, keep the hose nozzle or the funnel
and container in contact with the metal of the fuel
tank to avoid the possibility of an electrical spark
igniting the fuel.
2. Do not overfill the fuel tank - overflow creates a
fire hazard.
3. DO NOT SMOKE when refueling and never refuel
when engine is running.
4. Prevent fires by keeping the machine clean of
debris, grease and spilled fuel.
SAFETY
The Safety Alert Symbol identifies important safety
messages written on the paver decals, as well as, in this
manual. When you see this symbol, be alert to possible
danger that could result in serious injury or death.
Note the use of key signal words in association with
the Safety Alert Symbol:
DANGER - An immediate and specific hazard which will
result in severe personal injury or death if the proper
precautions are not taken.
WARNING - A specific hazard or unsafe practice which
could result in severe personal injury or death if proper
precautions are not taken.
CAUTION - Unsafe practices which could result in per-
sonal injury if proper precautions are not taken and as
a reminder of good safety practices.
YOU are responsible for the safe operation and main-
tenance of your Terex Bid-Well Paver. You must ensure
that you and anyone else who is going to operate, main-
tain or work around the machine be familiar with the
operating and maintenance procedures and all related
safety information contained in this manual.
GENERALSAFETYPRECAUTIONS
1. Always read and fully understand the Operator’s
Manual and the Safety Decals on the machine
before trying to operate or service this equipment.
2. It is wise to have a first aid kit available and to be
familiar with its contents.
3. Keep a “charged” fire extinguisher within reach
whenever you work in area where fire may occur.
Also, be sure you have the correct type of extin-
guisher for your situation:
Type A: Wood, paper, textile and rubbish.
Type B: Flammable liquids.
Type C: Electrical equipment.
 SAFETYALERTSYMBOL
PAGE1.4  2450CARRIAGEFOGGER(1/2012)

STORAGEPRECAUTIONS
1. Store paver in an area away from human activity.
2. Do not permit children to play on or around the
stored paver.
3. Make sure the unit is stored in an area that is firm,
level and free of debris.
4. Store the paver inside a building or cover securely
with a weatherproof tarpaulin.
SAFETYDECALS
1. Keep Safety Decals and signs clean and legible
at all times.
2. Replace decals and signs that are missing or be-
come impossible to read.
3. When replacing parts that previously displayed a
safety decal, be sure to replace the decal as well.
4. Obtain Safety Decals or signs from the Terex Bid-
Well Parts and Service Department.
5. Become familiar with the content and the position
of each Safety Decal. Important information is
written on the decals.
BATTERYPRECAUTIONS
1. Keep all sparks and flames away from battery, as
gas given off by electrolyte is explosive.
2. If you come in contact with battery electrolyte solu-
tion wash off immediately.
3. Always disconnect the battery ground cable before
working on the electrical system.
4. Do not tip battery more than 45 degrees to avoid
electrolyte loss.
TRANSPORTPRECAUTIONS
1. Consult the Terex Bid-Well Operator’s Manual
beforeattempting to lift your paver. Use extreme
caution when lifting the machine. Make sure that
the lifting device has enough capacity to lift the
weight of the machine. Check all lifting cables,
chains, clevises, cable clamps and spreader beams
for any damage. Use ropes tied to the ends of the
machine to prevent the machine from spinning.
Keep all personnel away from the machine while
it is being lifted.
2. Always comply with local regulations regarding
moving equipment on public roads and high ways.
3. Make sure that all lights and reflectors comply with
state and local regulations. Make sure that they
are clean, in good working order and can be seen
clearly by all overtaking and on-coming traffic.
DECALS
2450CARRIAGEFOGGER(1/2012)  PAGE1.5
#20-08137
#20-08338
#20-08338
#20-08352
#20-08227

PAGE1.6  2450CARRIAGEFOGGER(1/2012)
 TerexBid-WellLOWPRESSURECARRIAGEFOGGERSYSTEM
PURPOSEOFCARRIAGEFOGGINGSYSTEM
The Terex Bid-Well low pressure carriage fogging system provides a means to add humidity and lower
temperatures to the surface of concrete and/or the surrounding area. The fog helps to eliminate
shrinkage cracks due to abnormal surface drying or dehydration. (Works exceptionally well with flyash,
silica fume additives and overlays).
OPERATIONOFCARRIAGEFOGGER
To operate the carriage fogger, start the engine and at full throttle or 3600 RPM’s, rotate the flow con-
trol valve marked “Fogger” clockwise to open the flow of oil to the fogger pump. The fogging system
is set up to run between 40 and 60 PSI. There is a pressure setting valve located next to the fogger
pump.
All the nozzles, except for the two for the burlap drag, are rated for one (1) gallon per hour; the two
nozzles for the burlap drag are rated for four (4) gallons per hour. The nozzles located above the
paving rollers can be adjusted vertically and can be turned to spray directly onto the paving rollers or
directly onto the paving surface. The amount of fog can be controlled by decreasing pressure or by
turning the fogger flow control valve down to slow the pump. A shut off valve, located at the end of
each pipe, allows you to shut off the nozzles on one or both sides of the carriage and still operate the
nozzles located at the drag pan(s) and burlap drag.
The nozzles located at the drag pan(s) can be adjusted vertically and angled to obtain the desired fog
pattern. Each nozzle has an individual shut off. It may be advantageous to shut one of the nozzles off,
depending on wind velocity and direction, to avoid filling the drag pan(s) with water.
The two nozzles positioned at the burlap drag work best when angled inward, spraying directly on the
inside of the burlap. This will keep the burlap wet throughout the pour.
The length of the pour, the nozzle size, wind, temperature and humidity are all factors that may require
operator adjustment before and during every pour.
#20-08562
#20-08332
#20-08525

© 2010 Terex Corporation All Rights Reserved
Terex® is a registered trademark of Terex Corporation in the United States of America and many other countries. Products and services
listed may be trademarks, service marks, or trade names of Terex Corporation and/or its subsidiaries in the United States of America
and other countries, and all rights are reserved.
No part of this manual may be reproduced in any way without the express prior written consent of Terex Corporation.
TABLEOFCONTENTS
2450CARRIAGEFOGGER(1/2012)  PAGE1.7
 A. FOGGERPOWERUNITASSEMBLY............................................................................................. 1.8  1.9
 B. FOGGER,PLUMBINGSCHEMATIC............................................................................................ 1.10  1.11
 C. FOGGER,CARRIAGEHYDRAULICSCHEMATIC.................................................................... 1.12  1.13
 D. FOGGER,CARRIAGEUNITPLUMBINGSCHEMATIC..........................................................1.14  1.15
 E. FOGGER,MOUNTINGBRACKETS.............................................................................................. 1.16  1.17
 F. ASSEMBLYPHOTOGRAPHS........................................................................................................1.18  1.21

PAGE1.8  2450CARRIAGEFOGGER(1/2012)
 ITEM PARTNUMBER QTY DESCRIPTION
  122290  2450SINGLECARRIAGEFOGGER2010
1 105506 1 CARRIAGE FOGGER FRAME
2 101222 2 MOUNTING CLIP
3 41-60632 2 BOLT, 1/2-13 UNC X 4
4 41-11008 2 LOCKWASHER, 1/2
5 41-22008 2 HEX NUT, 1/2-13 UNC
6 117257 1 PUMP MOUNTING PLATE
7 41-60408 4 BOLT, 3/8-16 UNC X 1
8 41-10006 8 FLAT WASHER, 3/8
9 41-11006 4 LOCKWASHER, 3/8
10 41-22006 4 HEX NUT, 3/8-16 UNC
11 117242 1 PUMP SPACER
12 41-60406 4 BOLT, 3/8-16 UNC X 3/4
13 41-11006 4 LOCKWASHER, 3/8
14 41-22006 4 HEX NUT, 3/8-16 UNC
15 117256 1 PUMP SHIELD
16 41-60410 2 BOLT, 3/8-16 UNC X 1-1/4
17 41-10006 2 FLAT WASHER, 3/8
18 41-11006 2 LOCKWASHER, 3/8
19 41-22006 2 HEX NUT, 3/8-16 UNC
20 117258 1 FOGGER TANK SPACER
21 41-60406 4 BOLT, 3/8-16 UNC X 3/4
22 41-10006 4 FLAT WASHER, 3/8
23 41-11006 4 LOCKWASHER, 3/8
24 41-22006 4 HEX NUT, 3/8-16 UNC

2450CARRIAGEFOGGER(1/2012)  PAGE1.9
4
5
13
14
17
18
19
2
1
3
11
12
15
16
21
20
22
23
7
8
9
8
10
6
24

PAGE1.10  2450CARRIAGEFOGGER(1/2012)
 ITEM PARTNUMBER QTY DESCRIPTION
  122290  2450SINGLECARRIAGEFOGGER2010
1 111216 1 50 GALLON POLY TANK
2 RF-15018 2 HOLDING STRAP
* 41-10006 4 FLAT WASHER, 3/8 (NOTSHOWN)
* 41-24006 4 LOCK NUT, 3/8-16 UNC (NOTSHOWN)
3 11-46479 2 BUNG, 3/4 PVC PLASTIC
4 11-77404 7 GALV NIPPLE, 3/4 X 2
5 11-76404 2 90 DEGREE GALV ELBOW, 3/4
6 31-57214 1 BRASS BALL VALVE, 3/4
7 11-40014 5 STRAIGHT HOSE BARB, 3/4
8 102894 1 HOSE, 3/4 X 16”
9 26-40612 1 STRAINER, 3/4 POLY “Y”
10 11-76043 2 BUSHING, 3/4 X 1/2, GALV
11 11-77304 3 NIPPLE, 1/2 X 2, GALV
12 11-76253 1 TEE, 1/2, GALV
13 11-76031 1 BUSHING, 1/2 X 1/4, GALV
14 11-77100 1 NIPPLE, 1/4, CLOSED, GALV
15 31-57206 1 BRASS BALL/BUTTERFLY VALVE, 1/4
16 31-19944 1 HYPRO TWIN PISTON PUMP ASSEMBLY
INCLUDES:
31-19944-1 HYDRAULIC MOTOR
31-19944-2 HAYES SHAFT COUPLER
31-19944-3 5/8 SHAFT, 3/16 KEYWAY COUPLER HALF
31-19944-4 1 SHAFT, 1/4 KEYWAY COUPLER HALF
31-19944-5 NEOPRENE INSERT
31-19944-6 L-BRACKET
31-19944-7 HYPRO TWIN PISTON PUMP
* 41-60410 2 BOLT, 3/6-16 UNC X 1-1/4
* 41-11006 2 LOCKWASHER, 3/8
* 41-22006 2 HEX NUT, 3/8-16 UNC
17 31-00001 1 PRESSURE GAUGE 0 - 100 PSI
18 117259 1 GALV TEE, 3/4
19 11-76254 2 GALV TEE, 3/4
20 31-56525 1 RELIEF VALVE, BRASS
21 106132 1 HOSE, 3/4 X 27”
22 31-57299 1 GATE VALVE, 3/4
23 11-77413 1 GALV NIPPLE, 3/4 X 7
24 26-35200 1 RUST/SEDIMENT FILTER
* 26-35201 1 REPLACEMENT FILTER
* 20-08332 1 DECAL, CAUTION-USE POTABLE WATER ONLY
25 11-11265 1 BUSHING, 3/4 X 3/8
26 11-54106 1 STRAIGHT FITTING, 3/8 MP X 3/8 BRASS BARB
27 107942 1 HOSE, 3/4 X 54”
28 11-44005 1 90 DEGREE HOSE BARB, 3/4
29 31-90270 1 GLEASON REEL
30 22-00800 1 KELLUM GRIP
* 41-95080 1 NARROW RIM FLAT WASHER
31 37-06025 1 QUICK CLAMP
* 111749 2 HOSE, 3/8 X 60 FT

2450CARRIAGEFOGGER(1/2012)  PAGE1.11
50 GALLON
POLY TANK
HOSE REEL
1
2
3
28
7
23
4
4
11
18
19
29
30
31
12
13
14
15
17
10
9
7
8
76
4
3
5
16
27
IN OUT
4
11
10
11
4
4
5
20
19
7
77
21
22
5
4
24
25
26
27

PAGE1.12  2450CARRIAGEFOGGER(1/2012)
 ITEM PARTNUMBER QTY DESCRIPTION
  122290  2450SINGLECARRIAGEFOGGER2010
1 31-19944 1 HYPRO TWIN PISTON PUMP ASSEMBLY
2 11-20810 2 STRAIGHT ADAPTER, 8MJ-10MB
3 110602 2 HOSE ASSY, 1/2 X 18
4 11-55533 4 QUICK DISCONNECT, FEMALE, 1/2
* 11-55501 4 QUICK DISCONNECT, DUST PLUG
5 11-55535 4 QUICK DISCONNECT, MALE, 1/2
* 11-55506 4 QUICK DISCONNECT DUST CAP
6 107701 2 HOSE ASSY, 1/2 x 576
7 11-20803 2 BULKHEAD ADAPTER, 8MJ-8MJ
* 41-12012 2 FLAT WASHER, 3/4, SAE
8 108087 2 HOSE ASSY, 1/2 x 20”
9 107416 1 HOSE ASSY, 1/2 x 26”
10 11-20930 1 TEE ADAPTER, 8MJ-10MB-8MJ
* OF-202030 1 HANDLE, SPEED CONTROL
* 41-60310 1 BOLT, GR8 5/16 X 1 1/4
* 28-00200 1 KNOB
11 11-20928 2 SWIVEL TEE ADAPTER, 8MJ-8FJX-8MJ
12 31-51210 1 FCR VALVE, 2000 PSI
* 41-60220 2 BOLT, 1/4-20 UNC X 2-1/2
* 41-11004 2 LOCKWASHER, 1/4
* 41-22004 2 HEX NUT, 1/4-20 UNC
13 11-20510 2 90 DEGREE ELBOW ADAPTER, 8MJ-10MB
14 108184 1 HOSE ASSY, 1/2 x 24”
15 107685 1 HOSE ASSY, 1/2 x 108”
16 31-57150 1 SELECTOR PUSH/PULL VALVE
* 41-60314 2 BOLT, 5/16-18 UNC X 1-3/4
* 41-10005 2 FLAT WASHER, 5/16
* 41-11005 2 LOCKWASHER, 5/16
* 41-22005 2 HEX NUT, 5/16-18 UNC
17 11-20802 3 STRAIGHT ADAPTER, 8MJ-8MB
18 107279 1 HOSE ASSY, 1/2 x 24”
19 31-10421 1 HYDRAULIC PUMP
* 40-30008 1 COUPLING KIT
20 1120802 1 STRAIGHT ADAPTER, 8MJ8MB
21 1120813 1 STRAIGHT ADAPTER, 12MJ10MB
22 108889 1 HOSE ASSY, 3/4 X 60”
* OF-202030 1 HANDLE, SPEED CONTROL
HYDRAULICFITTINGSMAYVARYPERUNIT

2450CARRIAGEFOGGER(1/2012)  PAGE1.13
EX
IN
CF
TO HYD TANK
ON/OFF VALVE
CONTROL VALVE
FOGGER
PUMP
PUMP
IN
1
11
16
17
17
IN OUT
22
334
4 5 5
66
7 7
4
5
4
5
8
9
10 TO MANIFOLD
13
12
14
8
15
17
18
13
19
20
21
22

PAGE1.14  2450CARRIAGEFOGGER(1/2012)
 ITEM PARTNUMBER QTY DESCRIPTION
  122290  2450SINGLECARRIAGEFOGGER2010
1 28-00305 1 HOSE CLAMP
2 11-50041 1 1/4 MP X 3/8 BRASS HOSE BARB
3 31-57206 7 BALL VALVE, 1/4 FEMALE NPT
4 11-55490 3 BRASS MALE PLUG 1/4 NPT
5 11-55491 3 BRASS SOC. FEMALE 1/4 NPT
6 11-77100 3 NIPPLE, 1/4 NPT CLOSE
7 116768 1 DISCONNECT PLATE
8 11-55480 1 FEMALE BULKHEAD UNION, 3/8 X 1/4 NPT
9 11-55465 1 MALE CONNECTOR, 3/8 X 1/4 NPT
10 116927 2 TUBE, 3/8 X 36”
11 11-55470 2 UNION CROSS, 3/8 X 1/4 NPT
12 116928 2 TUBE, 3/8 X 25”
13 11-76021 2 BUSHING, 3/8 X 1/4 GALV.
14 11-76152 2 REDUCER, 1 X 3/8
15 105660 2 SPRAYBAR, 4 FT, 3-HOLE
16 32-00551 6 SPRAY BODY
17 26-50100 6 100 MESH SCREEN
18 40-32005 6 SEAL
19 32-00554 6 SPRAY CAP
* 45-92001 6 NOZZLE, 1 GAL
20 11-78016 2 GALV CAP, 1”
21 116926 1 TUBE, 3/8 X 4”
22 120012 4 TUBE, 3/8 X 25” (DUALPANQTY=6)
23 11-55460 4 MALE ELBOW, 3/8 X 1/4 NPT BRASS
24 117807 4 SPRAY NIPPLE MOUNT
25 11-55475 1 UNION TEE, 3/8 X 1/4 NPT
26 32-00553 4 SIDE SPRAY BODY
27 26-50100 4 100 MESH SCREEN
28 40-32005 4 SEAL
29 32-00554 4 SPRAY CAP
* 45-92001 2 NOZZLE, 1 GAL
* 45-92004 2 NOZZLE, 4 GAL
HYDRAULICFITTINGSMAYVARYPERUNIT

2450CARRIAGEFOGGER(1/2012)  PAGE1.15
SINGLE FOGGER
DRAG PAN
BURLAP DRAG
FROM TANK
DRAG PAN
BURLAP DRAG
1
2
3
4
5
6
7
8
9
10
11 12
12
9
5
4
3
6
13
14
15
9
5
4
3
6
13
14
15
16
17
18
19
20 20
21
11
22 22
24
3
23
24
3
23
23
3
24
22 25 22 23
3
24
26
27
28
29

PAGE1.16  2450CARRIAGEFOGGER(1/2012)
 ITEM PARTNUMBER QTY DESCRIPTION
  122290  2450SINGLECARRIAGEFOGGER2010
1 105718 4 FOGGER BAR MOUNTING BRACKET
2 105659 4 FOGGER BAR BRACKET MOUNT
3 41-60410 8 BOLT, 3/8-16 UNC X 1-1/4
4 41-11006 8 LOCKWASHER, 3/8
5 41-22006 8 HEX NUT, 3/8-16 UNC
6 41-60408 8 BOLT, 3/8-16 UNC X 1
7 41-11006 8 LOCKWASHER, 3/8
8 41-22006 8 HEX NUT, 3/8-16 UNC
9 105660 2 SPRAY BAR PIPE, 4 FT, 3-HOLE
10 28-00805 4 U-BOLT, 5/16
11 41-11005 8 LOCKWASHER, 5/16
12 41-22005 8 HEX NUT, 5/16-18 UNC
13 117802 2 DRAG PAN & BURLAP SPRAY HOSE MOUNT
14 117805 4 HORIZONTAL NOZZLE SLIDE TUBE
15 117807 4 SPRAYER NIPPLE MOUNT
16 114747 8 WING BOLT
17 106383 2 BACK PLATE
18 41-11006 4 LOCKWASHER, 3/8
19 41-22006 4 HEX NUT, 3/8-16 UNC
20 116768 1 DISCONNECT PLATE
21 28-00858 1 U-BOLT, 3/8
22 41-11006 2 LOCKWASHER, 3/8
23 41-22006 2 HEX NUT, 3/8-16 UNC
24 107853 1 HOSE REEL SPRAYER MOUNT
25 41-60612 4 BOLT, 1/2-13 UNC X 1-1/2
* 41-10008 8 FLAT WASHER, 1/2
26 41-11008 4 LOCKWASHER, 1/2
27 41-22008 4 HEX NUT, 1/2-13 UNC
28 102501 1 3-WIRE MOUNTING CHANNEL
29 41-60424 2 BOLT, 3/8-16 UNC X 3
30 41-11006 2 LOCKWASHER, 3/8
31 41-22006 2 HEX NUT, 3/8-16 UNC
32 41-60632 4 BOLT, 1/2-13 UNC X 4
33 41-11008 4 LOCKWASHER, 1/2
34 41-22008 4 HEX NUT, 1/2-13 UNC
35 31-90270 1 GLEASON REEL
36 RF-22545 1 HOSE SUPPORT TUBE
37 41-34612 1 SCREW, 1/2-13 UNC X 1-1/2, SQ HD
* 41-23008 1 JAM NUT, 1/2-13 UNC
38 RF-15022 1 HOSE SUPPORT TUBE MOUNT
39 41-60628 2 BOLT, 1/2-13 UNC X 3-1/2
* 41-10008 2 FLAT WASHER, 1/2
* 41-11008 2 LOCKWASHER, 1/2
* 41-22008 2 HEX NUT, 1/2-13 UNC
40 41-78003 1 EYEBOLT
* 41-11006 1 LOCKWASHER, 3/8
* 41-22006 1 HEX NUT, 3/8-16 UNC
41 37-06025 1 QUICK CLAMP
* 22-00800 1 KELLUM GRIP
36
20
21
38
39
40
41
37

2450CARRIAGEFOGGER(1/2012)  PAGE1.17
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15
16
16
13
16
15
15
17
17
18
18
19
19
20
21
22
23
1
2
24
25
26
27
28
29
30
31
32
33
34
35

PAGE1.18  2450CARRIAGEFOGGER(1/2012)

2450CARRIAGEFOGGER(1/2012)  PAGE1.19

PAGE1.20  2450CARRIAGEFOGGER(1/2012)