TES TDS-55-P User manual

TDS-55-P standard version
TDS-55-P
Touch Monitor
User Manual
Version 2.0 2018/07

1
About This Document
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by any
means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or
otherwise without prior written permission of TES Touch Embedded Solutions Inc..
The information in this document is subject to change without notice. TES makes no
representations or warranties with respect to the contents herein, and specifically disclaims
any implied warranties of merchantability or fitness for a particular purpose. TES reserves
the right to revise this publication and to make changes from time to time in the content
hereof without obligation of TES to notify any person of such revisions or changes.
Windows is a registered trademark of Microsoft, Inc. Other brand or product names are
trademarks of their respective holders.

2
Compliance Information
For FCC (USA)
This equipment has been tested and fund to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. There limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
For IC (Canada)
CAN ICES-3(A)/NMB-3(A)
For CE (EU)
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive
2014/35/EU
Warning:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

3
Usage Notice
Precautions
Please follow all warnings, precautions and maintenance as recommended in this user’s
manual to maximize the life of your unit.
Do ：
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the product housing.
Use only the qualified power adapter that comes with your device.
Disconnect the power plug from AC outlet if the product is not going to be used for an
extended period of time.
Don’t ：
Do not use abrasive cleaners, waxes or solvents for your cleaning.
Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
! Warning - To prevent the risk of fire or shock hazards, and do not
expose the product to moisture.
! Warning - Please do not open or disassemble the product as this may
cause electric shock.

4
Table of Contents
Chapter 1......................................................................................................................5
1.1 Overview....................................................................................................................6
1.2 Feature.......................................................................................................................6
1.3 Specifications.............................................................................................................6
1.4 Block Diagram............................................................................................................7
1.5 Interface Connectors..................................................................................................7
1.5.1 Power Connector................................................................................................7
1.5.2 Video Signal Connector......................................................................................8
1.5.3 Signal Connector................................................................................................9
1.6 Package Overview...................................................................................................11
Chapter 2....................................................................................................................12
2.1 About VESA Mount ..................................................................................................13
2.1.1 Install the VESA screw.....................................................................................14
2.2 About General Mounting Information .......................................................................15
2.2.1 Landscape........................................................................................................15
2.2.2 Portrait..............................................................................................................15
2.3 On-Screen Display...................................................................................................16
2.3.1 OSD Function Description................................................................................17
2.3.2 Timing Table Chart...........................................................................................18
2.3.3 EDID Data........................................................................................................18
2.4 Dimension................................................................................................................19
2.4.1 Front View........................................................................................................19
2.4.2 Side View .........................................................................................................19
2.4.3 Rear View.........................................................................................................20
2.4.4 Back View.........................................................................................................20
Appendix....................................................................................................................21

5
Chapter 1
Product Introduction

6
1.1 Overview
The TDS-55A Series is a 55" large size thin-film transistor (TFT) liquid crystal display
(LCD).This unit is to be used as commercial and light industrial equipment only.
1.2 Feature
4K2K High Resolution Display
Dynamic Touch Sensitivity Technology Supports up to 6mm Thickness glass
Portrait and Landscape Display for All Solutions.
Touch Screen Support up to 40 Points Touch.
Supports 24/7 non-stop Operate Service.
1.3 Specifications
LCD Touch Panel
Size
55” TFT LCD
Brightness
500 cd/m2(Non-touch screen)
425 cd/m2 (P-CAP)
Number of Pixels
3840(H) x 2160(V)
Touch Type
P-CAP/ 40 points
Environment
Power Input
AC 100 ~ 240V, 50/60Hz
Operating Temperature
0C ~ 40C
Storage Temperature
-20C ~ 60C
Operating Humidity
20% ~ 80% RH, non-condensing
Mounting
VESA 400 mm x 400 mm
Dimension (W x H x D)
1247.6mm x 78.8mm x 732.4mm
Net Weight
30.75 kg
Gross Weight
37.21 kg

7
1.4 Block Diagram
This section describes the electrical requirements of the monitor. The block diagram in figure
1 illustrates the various electrical sub-systems.
1.5 Interface Connectors
1.5.1 Power Connector
The AC converter shall have an IEC320 type male power receptacle for connection to AC
mains power. The power cord, exact type to be supplied in the appropriate Option Kit, shall be
length of 1.8 0.05 meters, and PC99 compliant.

8
1.5.2 Video Signal Connector
The video signal input via HDMI female connector.
Connector Pin Assignment:
Pin
Signal
Pin
Signal
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock–
3
TMDS Data2–
13
CEC
4
TMDS Data1+
14
Reserved (N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1–
16
SDA
7
TMDS Data0+
17
DDC/CEC Ground
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0–
19
Hot Plug Detect
10
TMDS Clock+
The video signal input via DVI female connector.
Connector Pin Assignment:
Pin
Signal
Pin
Signal
1
TMDS Data 2-
16
Hot Plug Detect
2
TMDS Data 2+
17
TMDS Data 0-
3
TMDS Data 2/4 Shield
18
TMDS Data 0+
4
TMDS 4-
19
TMDS Data 0/5 Shield
5
TMDS 4+
20
TMDS Data 5-
6
DDC Clock
21
TMDS Data 5+
7
DDC Data
22
TMDS Clock Shield
8
Analog vertical sync
23
TMDS Clock+
9
TMDS Data 1-
24
TMDS Clock-C1
10
TMDS Data 1+
C1
Analog red
11
TMDS Data 1/3 Shield
C2
Analog green
12
TMDS 3-
C3
Analog blue
13
TMDS 3+
C4
Analog horizontal sync
14
+5V DDC Power
C5
Analog ground Return for R,G,B signals
15
Gnd (+5, Analog V/H Sync)

9
The video signal input via Display Port (1.2) connector.
Connector Pin Assignment:
Pin
Signal
1
ML_Lane 3(n) Data3 -
2
Signal ground
3
ML_Lane 3(p) Data3 +
4
ML_Lane 2(n) Data2 -
5
Signal ground
6
ML_Lane 2(p) Data2 +
7
ML_Lane 1(n) Data1 -
8
Signal ground
9
ML_Lane 1(p) Data1 +
10
ML_Lane 0(n) Data0 -
11
Signal ground
12
ML_Lane 0(p) Data0 +
13
Signal ground
14
Signal ground
15
AUX_CH(p) AUX + Signal for Auxiliary Channel
16
Signal ground
17
AUX_CH(n) AUX - Signal for Auxiliary Channel
18
Hot Plug
19
DP_PWR Return
20
DP_PWR
1.5.3 Signal Connector
USB Connector
Pin
Description
1
VCC
2
D-
3
D+
4
GND
RJ11 Connector (Remote Key)
Pin
Description
1
MENU
2
UP
3
DOWN
4
SELECT
5
POWER
6
GND

10
Audio Line in / Line out connector

11
1.6 Package Overview
LCD Display
Power Cord
Audio cable
USB Cable (A to B)
HDMI Cable
DVI to VGA cable
Quick Start Guide
CD
Screw (M4)
x 20 pcs
! Warming!
This product is intended to be supplied by a AC-in Power source, rated
100V~240V, 1.3~2.5A 50/60Hz minimum, Tma = 40 degree C minimum, and the
altitude of operation = 3048m minimum. If it needs further assistance with
purchasing the power source, please contact to TES for further information.

12
Chapter 2
Product Installation

13
2.1 About VESA Mount
The TDS-55 series conform to the “VESA Flat Display Mounting Interface Standard”which
defines a physical mounting interface for touch monitor and corresponding with the standards
of touch monitor mounting devices. The VESA mount is located on the back of this unit.
! Warming!
Please select the TES original screws!
The distance between the back cover surface and the bottom of the screw hole
is 6~7 mm. Please use M5 screws diameter with proper length to mount your
monitor.

14
2.1.1 Install the VESA screw
Note: Please install/ dismantle the product when the device is in the shutdown state.
Step 1: Fasten two M6 screws nut into the VESA hole
The length of screw nut is 30mm

15
2.2 About General Mounting Information
The following two mounting orientations are supported: Landscape and portrait mode. For
optimal touch performance, ensure that the monitor is supported fully and is as flat as
possible.
2.2.1 Landscape
2.2.2 Portrait

16
2.3 On-Screen Display
The TDS-55 Lite series provide side panel controls. And the following is OSD function table:
OSD
Key
Menu off status
Menu on status
MENU
Menu appear
Menu disappear/ return to main item
▲
Brightness
Main item select up/ Adjust up
▼
Contrast
Main item select down/ Adjust down
SELECT
Auto Adjusting
Enter/Select sub-item function
Power On/Off
1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down”
button to select among the five functions in the main menu.
2. Press “SELECT” to enter the sub menu, and then use “Up” or “Down” button to select
the adjustable functions.
3. Choose the adjustment items in the sub menu by pressing the “SELECT” button.
4. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.
5. With the OSD menu on screen, press “Menu” button to return main menu or exit OSD.
6. The OSD menu will automatically close, if you have left it idle for a pre-set time.
7. To Lock the OSD / Power menu buttons, please follow the instructions below.
(Please note: the monitor has to be turned ON with a valid signal pre-set)
a. Without the OSD menu on screen, press and hold “Menu” key, and press “POWER”
once then release “MENU” key. The “Lock/Unlock” menu will appear for 5 seconds.
b. Use the "UP” and “DOWN key to select OSD or Power setting then set at “Lock” (or
“Unlock” ) by pushing the "ENTER" button.
c. When pressing “MENU” button, the previous setting will be saved and exit the
“Lock/Unlock” menu automatically.
Please note:
1. When the OSD Lock function is selected, this indicates that all the buttons except “power”
button are now disabled.
2. When the Power Lock function is selected, this indicates that the power key is disabled;
user can not to turn off the monitor by "Power" key.
3. How to enter factory OSD menu, please follow the instructions below.

17
a. Without the OSD menu on screen, press and hold “Menu” key ,and press “UP”
once then release “MENU”key. The factory menu will appear on the screen.
d. Use the "UP”and “DOWN key to select main functions, then press “SELECT”to
enter sub menu for adjusting (or setting) those values.
c. Select “GoTo Main”and press “SELECT”to exit factory OSD menu, it will
automatically switch to user menu for normal OSD operation.
4. In power saving status, to press “Menu”button can wake up OSD for selecting video port.
2.3.1 OSD Function Description
ITEM
CONTENT
Default
Contrast
The monitor luminance level control.
50
Brightness
The monitor backlight level control.
50
Auto Adjust
Automatically adjusts the screen image of VGA signal,
affecting the H-position, V-position, Frequency, and
Phase menu.
NA
Left/Right
Moving screen image horizontal position to left or right.
NA
Up/Down
Moving screen image vertical position to up or down.
NA
Horizontal size
The screen image horizontal dot clock adjustment.
NA
Fine
The screen image pixel phase adjustment.
NA
OSD Left/Right
Moving OSD menu horizontal position to left or right.
50
OSD Up/Down
Moving OSD menu vertical position to up or down.
50
OSD Time out
OSD auto-disappear time selection.
15
OSD Language
OSD menu language selection.
( English, French, Deutsch, Italian, Spanish, Japanese
, Simplified Chinese and Korean )
English
Factory Reset
Factory default value restored.
NA
Color
Temperature
Color temperature selection.
(5500K, 6500K, 7500K, 9300K, User; default: User )
USER
Red
Red gain of selected color temperature.
(only User mode can be adjusted)
97
Green
Green gain of selected color temperature.
(only User mode can be adjusted)
100
Blue
Blue gain of selected color temperature.
(only User mode can be adjusted)
97

18
2.3.2 Timing Table Chart
Mode
Resolution
H-Freq.
(KHz)
Bandwidth
(MHz)
Polarity
H
V
1
VGA 640x480 60Hz
31.47
25.175
-
-
2
VESA 800x600 60Hz
37.88
40
+
+
3
VESA 1024x768 60Hz
48.36
65
-
-
4
VESA 1280x720 60Hz
44.772
74.5
-
+
5
VESA 1280x768 60Hz
47.776
79.5
-
+
6
VESA 1280x1024 60Hz
64
108
+
+
7
VESA 1280x960 60Hz
60
108
+
+
8
VESA 1440x900 60Hz
56
106.5
-
+
9
VESA 1360x768 60Hz
47.712
85.5
+
+
10
VESA 1680x1050 60Hz
65.2
146
-
+
11
FHD 1920x1080 60Hz
67.5
148.5
+
+
12
WQHD 2560x1440 60Hz(RB)
88.787
241.5
+
-
13
UHD 3840x2160 30Hz
67.5
297
+
+
14
UHD 3840x2160 60Hz
135
594
+
+
2.3.3 EDID Data
The monitor assembly shall provide a display communications channel that conforms to
VESA DDC2B hardware requirements. This configuration shall contain the 128-byte EDID file
as specified by VESA EDID Standard.

19
2.4 Dimension
2.4.1 Front View
2.4.2 Side View