Hubbell Litecontrol 22L Series User manual

2.500
2.750
2.750
2.500
2.750 .500
2.500
LPA CROSS SECTION
2.750 .500
2.500
7.000
2.874
.875 .425
5.124
3.280
R.219
R.117
PENDANT MOUNT
STD CROSS SECTION
LPA CROSS SECTION
WALL MOUNT
NOTES:
READ ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 1.
FIXTURES ARE SUPPLIED WITH FACTORY INSTALLED BRANCH CIRCUIT WIRING. REFER TO 2.
SUPPLEMENTAL INSTRUCTION SHEET FOR MAKING CONNECTIONS.
AIRCRAFT CABLES AND/OR WALL BOX ASSEMBLIES, AND ENDCAP KITS ARE SHIPPED 3.
SEPARATELY.
STD CROSS SECTION
litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN. IF
YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 22L
MOUNTING TYPE: PENDANT/WALL
REV / DATE: 0 / 10/19/18
PAGE: 1 OF 3
SUPPLIED BY INSTALLER
TOOLS REQUIRED
DRAWING: 510688
7/16" SOCKET/WRENCH (WALL MOUNT ONLY)
11/32" WRENCH/SOCKET OR PLIERS

1 2 3 4
5 6 7
A
D
INSERT HERE AND ROTATE UP
B
C
IF INSTALLING A ROW, JOIN FIXTURES
TOGETHER USING SCREWS IN HARDWARE KIT.
WIRING CONNECTIONS CAN GO THROUGH
BOTTOM HOLES IN END HEADERS
F
H
REMOVE LED ASSEMBLY BY REMOVING
(6) #8 SHEET METAL SCREWS
G
REPEAT STEP 3 AND INSTALL END
OF ROW END CAP
RE-INSTALL LED
ASSEMBLY
LOCATE AIRCRAFT CABLES ALONG A STRAIGHT LINE
IN CEILING PER DIMENSIONS SHOWN ON PAGE 1
(REFER TO INSTRUCTION SHEET 510481)
ON BOTH SIDES OF FIRST FIXTURE IN ROW (OR INDIVIDUAL) INSTALL
SWAGES ON YOKES BY INSERTING INTO HOLES IN END HEADER
ALONG FIXTURE AXIS AND ROTATING UPWARDS
INSTALL END CAP ON BEGINNING
OF ROW SIDE (OR BOTH SIDES OF
INDIVIDUAL FIXTURE) BY
INSERTING WELD STUDS INTO
PROPER HOLES (BE CAUTIOUS OF
LEFT HAND VS RIGHT HAND) AND
SECURING WITH #8-32 NUTS
PROVIDED IN END CAP KIT
(SHIPPED SEPARATELY)
RAISE FIXTURE UP AND INSTALL CABLE
HANGERS ONTO AIRCRAFT CABLE AND
MAKE WIRING CONNECTIONS
litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN. IF
YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 22L
MOUNTING TYPE: PENDANT
REV / DATE: 0 / 10/19/18
PAGE: 2 OF 3
DRAWING: 510688

1
2
3
4
5
6 7
FIXTURE LENGTH
6.000 6.000
BACK VIEW
E
J
N
REMOVE LED ASSEMBLY BY REMOVING
(6) #8 SHEET METAL SCREWS
K
K
RAISE FIXTURE ONTO WALL BRACKET STUDS AND SECURE 1/4-20
NUTS FROM INSIDE. DO NOT FULLY TIGHTEN AT THIS TIME.
L
M
LOCATE WALL BOX LOCATIONS
ACCORDING TO BACK VIEW ABOVE
INSTALL END CAP ON
BEGINNING OF ROW SIDE (OR
BOTH SIDES OF INDIVIDUAL
FIXTURE) BY INSERTING WELD
STUDS INTO PROPER HOLES
(BE CAUTIOUS OF LEFT HAND
VS RIGHT HAND) AND
SECURING WITH #8-32 NUTS
PROVIDED IN END CAP KIT
(SHIPPED SEPARATELY)
IF INSTALLING A ROW, JOIN FIXTURES
TOGETHER USING SCREWS IN HARDWARE KIT.
WIRING CONNECTIONS CAN GO THROUGH
BOTTOM HOLES IN END HEADERS. TIGHTEN
WALL MOUNT BRACKET NUTS.
RE-INSTALL LED
ASSEMBLY
REPEAT STEP 3 AND INSTALL END
OF ROW END CAP
litecontrol.com
DO NOT MODIFY OR ALTER THIS PRODUCT IN ANY WAY, OR INSTALL IN ANY FASHION WHICH IS CONTRARY TO THE INSTRUCTIONS CONTAINED HEREIN. IF
YOU HAVE ANY QUESTIONS REGARDING THIS PRODUCT OR THE INSTALLATION OF IT, PLEASE CALL LITECONTROL ENGINEERING AT 781-294-0100.
INSTALLATION INSTRUCTIONS
FIXTURE SERIES: 22L
MOUNTING TYPE: WALL
REV / DATE: 0 / 10/19/18
PAGE: 3 OF 3
DRAWING: 510688