IOTA ILB CP20 HE AELR HV User manual

ILB CP20 HE AELR HV
“A” MOUNTING STYLE
BLUETOOTH-ENABLED EMERGENCY
LIGHTING EQUIPMENT FOR LED
P.O. BOX 11846 TUCSON, AZ 85734
[phone] • FAX [phone]
www.iotaengineering.com
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.
power is supplied to the unit.
2. CAUTION – This fixture provides more than one power supply output source. To reduce the risk of electrical
shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon-
necting the unit connector.
3. CAUTION – This is a sealed unit. Components are not replaceable. Replace the entire unit when necessary.
4. CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before
opening.
5. The ILB CP20 HE AELR HV is for use with grounded LED luminaires listed to UL standards. Not for use in
heated air outlets or hazardous locations.
6. The ILB CP20 HE AELR HV requires an unswitched A.C. power source of 120 to 277 volts AC, 50/60Hz.
7. The ILB CP20 HE AELR HV and A.C. driver must be on the same branch circuit.
8. Do not mount near gas or electric heaters.
9. The ILB CP20 HE AELR HV should be mounted in locations and at heights where it will not readily be sub-
jected to tampering by unauthorized personnel.
10. The ILB CP20 HE AELR HV will supply 50-200 VDC output at the individual rated specification for 90 minutes.
See individual units for output specifications.
11. The ILB CP20 HE AELR HV is certified in the CA Title 20 Modernized Appliance Efficiency Database System
(MAEDBS) as a small battery charger.
12. Suitable for use in damp locations and plenum spaces.
13. Suitable for luminaires, recessed Type IC (intended for insulation contact).
14. For use in 0° C minimum, 55° C maximum ambient temperatures.
15. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void
warranty, and result in non-compliance with UL specifications.
16. Do not use this equipment for other than intended use.
17. Install in accordance with the National Electrical Code and local regulations.
18. Lighting fixture manufacturers, electricians, and end-users need to ensure product system compatibility before
final installation. See addendum for compatibility and covered luminaire requirements.
SAVE THESE INSTRUCTIONS
INSTRUCTION MANUAL
HIGH EFFICIENCY PERFORMANCE
MEETS CA T20 BATTERY CHARGER
EFFICIENCY STANDARDS
EMERGENCY LED DRIVER FOR USE
WITH LED LUMINAIRES IDENTIFIED
IN THE MANUFACTURER’S
INSTALLATION INSTRUCTIONS
E99113

Page 2
LUMINAIRE HOUSING
TBTS NUT
CAUTION: Before installing, make certain A.C. power is o and the unit connector is disconnected.
STEP 2 - WIRING TO THE LED LOAD AND NORMAL DRIVER
STEP 1 - MOUNTING THE ILB CP20 HE AELR HV
STEP 3 - INSTALLING THE THREE-COLOR TEST SWITCH (TCTS)
The ILB CP20 HE AELR HV should be mounted on or nearby
the xture above the ceiling. The ex conduit marked “A”
should be wired into the driver/lamp compartment or to an
electrical junction box on the xture which allows access to the
xture connections.
The ILB CP20 HE AELR HV can be used with most LED loads that operate at 50-200 VDC. See the ILB Model Specication
Chart for output specications of the unit being installed.
1. The ILB CP20 HE AELR HV series has been evaluated to and found
compliant to UL standard 924. The as-installed performance of system
must meet or exceed all Federal, State, and Local code requirements.
2. Refer to Addendum 11042014 for detailed specications and methods to
calculate emergency light levels.
A. Cut a single gang switch box into the ceiling tile
adjacent to the xture within reach of the ILB
CP20 HE AELR HV ex conduit marked “B”.
After mounting the switch box, connect ex to the
box and route all leads inside the box.
B. Attach the switch box plate into
the switch box. Insert the TCTS
into the switch box plate hole
so that it is facing outside the
switch box. Secure the TCTS
against the plate by screwing
on the TCTS nut.
INSTALLATION INSTRUCTIONS
APPLICATION
Refer to the appropriate wiring diagram below. Make sure all connections are in accordance with NEC and any other
local requirements.
SWITCH BOX PLATE
TCTS NUT
ILB CP20 HE AELR HV 20 WATTS
ILB MODEL SPECIFICATION CHART
OUTPUT POWER (CONSTANT)
ILB CP HE CLS - WITH TCTS TEST ACCESSORY
ILB-CP-HE-CLS.EPS
TCTS
TEST ACCESSORY
RED OR RED/BLK
RED/BLK
WHT/RED
ORANGE
WHITE OR WHT/RED
ORANGE
ILB CP20 HE AELR HV
OPTIONAL T-BAR MOUNTING KIT
CEILING T-GRID
FIXTURE
FLEX “A” CONDUIT
FIXTURE
JUNCTION BOX
OR
WIRING
COMPARTMENT
SWITCH BOX FOR TBTS
(BOX NOT SUPPLIED)
FLEX “B” CONDUIT
TO TEST ACCESSORIES
OPTIONAL T-BAR MOUNTING KIT
CEILING T-GRID
FIXTURE
FLEX “A” CONDUIT
FIXTURE
JUNCTION BOX
OR
WIRING
COMPARTMENT
SWITCH BOX FOR TBTS
(BOX NOT SUPPLIED)
FLEX “B” CONDUIT
TO TEST ACCESSORIES
TCTS
TCTS
ILB CP20 HE AELR HV
ILB CP20 HE AELR HV
C. Connect the TCTS wires to the
ILB CP20 HE AELR HV per the
diagram above, matching similar
colored wire terminals if quick
disconnect terminal is present.
Attach the appropriate labels
adjacent to the TCTS. Annotate the
Replacement Label with identical
manufacturer part number(s).
ILB CP HE CLS - WITH TCTS TEST ACCESSORY
ILB-CP-HE-CLS.EPS
AC (NORMAL)
DRIVER
IOTA ILB CP HE AELR
EMERGENCY DRIVER
LED
LOAD
BLK/WHT
AC INPUT (120 TO 277V)
RED (+)
BLUE (-)
RED/WHT (+)
BLUE/WHT (-)
LED INPUT(+)
LED INPUT (-)
LED OUTPUT (+)
LED OUTPUT (-)
PRE-CONNECTED QUICK DISCONNECT
TERMINALS ARE ON SELECT MODELS
ONLY. MATE TERMINALS WITH SIMILAR
COLORED WIRES IF REPLACING A UNIT.
1
1
1

Page 3
STEP 4 - WIRING THE AC INPUT
The ILB CP20 HE AELR HV requires an unswitched AC input of 120-277 volts. Connect the BLACK/ORANGE wire to an
unswitched 120-277 Line, and the WHITE wire to the Neutral. The remaining BLACK/WHITE wire must be connected to
either an unswitched line, or a switched line input.
STEP 5 - LEDCODE CONNECTIONS
The ILB CP20 HE AELR HV is equipped with LEDCode wires that are used to interface with a Connected/LEDCode-enabled
normal driver. Cap the Yellow and Brown wires separately if LEDcode wires are not present on the normal driver.
COMPLETING INSTALLATION
STEP 6 - APPLY AC POWER AND MATE UNIT CONNECTOR
A. Apply continuous AC power to the unit and mate the ILB CP20 HE AELR HV unit connector. Allow the unit to
charge for at least 1 hour before performing a functional test.
B. Verify that the TCTS light is on. The TCTS LED will blink ashing Amber providing a visual indication that the battery is
being charged, or will be lit solid Green if the battery is fully charged.
C. Press and hold the TCTS button. The LED Module should be operating at a reduced light output. To complete the test,
release the TCTS button. If the LED Module in the xture returns to normal operation, the unit is ready for normal and
emergency service. If not, contact Customer Service.
OPERATION
Normal Mode
A.C. power is present. The A.C. Driver operates the LED Module as intended. The ILB CP20 HE AELR HV is in the standby
charging mode. The TCTS will be lit providing a visual indication that the battery is being charged.
Emergency Mode
The A.C. power fails. The ILB CP20 HE AELR HV senses the A.C. power failure and automatically switches to the Emergen-
cy Mode. The LED Module is illuminated, at reduced output, for a minimum of 90 minutes. When the A.C. power is restored,
the ILB CP20 HE AELR HV switches the system back to the Normal Mode and resumes battery charging.
ILB CP HE CLSR - WITH TCTS TEST ACCESSORY
ILB-CP-HE-CLS.EPS
IOTA ILB CP HE AELR
EMERGENCY DRIVER
WHITE
BLK/WHT
COMMON
UNSWITCHED
24/7 LINE
BLK/ORG (120 TO 277V, 50/60HZ)
SWITCHED OR
UNSWITCHED LINE
PRE-CONNECTED QUICK DISCONNECT
TERMINAL IS ON SELECT MODELS ONLY.
MATE TERMINAL WITH SIMILAR COLORED
WIRES IF REPLACING A UNIT.
1
1
ILB CP HE CLS - WITH TCTS TEST ACCESSORY
ILB-CP-HE-CLS.EPS
IOTA ILB CP HE AELR
EMERGENCY DRIVER
YELLOW
BROWN
LEDCODE (+)
LEDCODE (-)
!Cap wires if unused
PRE-CONNECTED QUICK DISCONNECT
TERMINAL IS ON SELECT MODELS ONLY.
MATE TERMINAL WITH SIMILAR COLORED
WIRES IF REPLACING A UNIT.

Rev. 2108
68F10-109A Addendum Insert
Addendum: Finalizing Installation with Bluetooth Junction Box Models
ILB CP HE AELR models come equipped with a Bluetooth Module Junction Box to be used to pair with a connected emergency
lighting management platform. Note: The Bluetooth Module Components have been pre-installed by the factory; nothing
needs to be connected by the end user.
This step must be completed after the ILB CP HE AELR has been installed in the mounting location and connected to
the luminaire. DO NOT attempt to complete this step rst. See the ILB CP HE AELR instruction manual for full installa-
tion instructions.
1) Install the junction box in a suitable loca-
tion where the test switch is visible. Ensure
the test switch is facing down.
2) Remove the screws from the test switch
faceplate to lift it from the junction box.
3) Mate the unit connector inside the junc-
tion box after continuous AC power has been
applied to the unit.
UNIT CONNECTOR
To ensure proper Bluetooth operation, the Junction Box must be installed with the test
switch facing down.
COMPLETING INSTALLATION - MATE THE UNIT CONNECTOR
COMPLETE WIRING DIAGRAM - WITH BLUETOOTH JUNCTION BOX
ILB CP HE CLS - WITH BLUETOOTH JUNCTION BOX
ILB-CP-HE-CLS-WITH-BT-MODULE.EPS
IOTA ILB CP HE CLSR
EMERGENCY DRIVER
AC (NORMAL)
DRIVER LED
LOAD
BT
MODULE
WHITE
WHITE
BLK/WHT
BLK/WHT
UNSWITCHED
24/7 POWER BLK/ORG (120 TO 277V, 50/60HZ)
AC INPUT (120 TO 277V)
SWITCHED OR
UNSWITCHED
HOT
COMMON
RED (+)
BLUE (-)
RED/WHT (+)
BLUE/WHT (-)
LED OUTPUT(+) LED OUTPUT (-)
INPUT (+)
INPUT (-)
UNIT
CONNECTOR
FLEX
B
JUNCTION BOX
FLEX
A
RED/BLK
RED OR RED/BLK
WHT/RED
ORANGE
WHT OR WHT/RED
ORANGE
ATTENTION: DO NOT MATE UNIT CONNECTOR UNTIL
INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED.
MATE UNIT CONNECTOR AFTER INSTALLATION IS
COMPLETE AND AC POWER IS SUPPLIED
YELLOW (LEDCODE +)
BROWN (LEDCODE -)
PRE-CONNECTED QUICK DISCONNECT TERMINALS.
MATE TERMINALS WITH SIMILAR COLORED
WIRES IF REPLACING A UNIT.
BT MODULE
(PRE-INSTALLED BY
THE FACTORY)
ILB CP HE AELR
EMERGENCY DRIVER

Page 4
“Written records of testing shall be kept by the owner for inspection by the authority having jurisdiction.”
SERVICING SHOULD BE PERFORMED BY QUALIFIED PERSONNEL.
Consult Customer Service or visit www.iotaengineering.com for current warranty information.
FULL WIRING DIAGRAM
Load Calibration
48 hours after the unit connector is joined, the ILB CP20 HE AELR HV will conduct a Load Calibration. Note: after the Load Calibration is
complete, any changes to the LED load that will a󰀨ect its nominal input voltage will necessitate a new Load Calibration. See Table 2 for the
sequence of button presses to conduct a manual Load Calibration.
ILB CP HE CLS - WITH TCTS TEST ACCESSORY
ILB-CP-HE-CLS.EPS
AC (NORMAL)
DRIVER
IOTA ILB CP HE AELR
EMERGENCY DRIVER
LED
LOAD
WHITE
WHITE
BLK/WHT
BLK/WHT
COMMON
UNSWITCHED
24/7 POWER BLK/ORG (120 TO 277V, 50/60HZ)
AC INPUT (120 TO 277V)
SWITCHED OR
UNSWITCHED
HOT
TCTS
TEST ACCESSORY
RED (+)
BLUE (-)
RED/WHT (+)
BLUE/WHT (-)
LED INPUT(+)
LED INPUT (-)
LED OUTPUT (+)
LED OUTPUT (-)
UNIT
CONNECTOR
RED OR RED/BLK
RED/BLK
WHT/RED
ORANGE
WHITE OR WHT/RED
ORANGE
ATTENTION: DO NOT MATE UNIT CONNECTOR UNTIL
INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED.
TEST ACCESSORY LEADS-OBSERVE
PROPER POLARITY WIRING.
PRE-CONNECTED QUICK DISCONNECT
TERMINALS ARE ON SELECT MODELS ONLY.
MATE TERMINALS WITH SIMILAR COLORED
WIRES IF REPLACING A UNIT.
CAP THE LEDCODE WIRES
IF NOT CONNECTED TO THE
LEDCODE BUS
YELLOW
BROWN
LEDCODE (+)
LEDCODE (-)
3
MATE UNIT CONNECTOR AFTER
INSTALLATION IS COMPLETE AND
AC POWER IS SUPPLIED
4
4
3
33
3
TESTING AND MAINTENANCE
Automatic Testing
The ILB CP20 HE AELR HV is designed to automatically test its emergency
function for 60 seconds monthly and 90 minutes annually. Automatic
testing will begin within 28 days after the unit is connected to A.C. Power
and the batteries have been installed.
If the ILB CP20 HE AELR HV detects a failure it will ash a status code
through the TCTS. See Table 1: TCTS Self Diagnostic Status Codes to identify
the fault state of the ILB CP20 HE AELR HV. Test results will also be acces-
sible in the connected emergency lighting system software application (if
connected).
Manual Testing
Manual Testing can be performed on the ILB CP20 HE AELR HV, provided
the unit is fully charged, by pressing and releasing the TCTS. Manual Testing
cannot be initiated until the unit has received a full 24 hour charge. Manual
Testing will not interfere with the automatic testing schedule of the ILB CP20
HE AELR HV and will display the same diagnosis indicators as automatic
testing.
Manual test sequences can be started by pressing the TCTS according to the
patterns listed in Table 2: Manual Test Sequences. A record of this manual test
will be accessible in the connected emergency lighting system software ap-
plication (if connected).
TCTS Color
Flashing Amber Battery is charging
Green Battery is fully charged
O Emergency mode
Flashing Green Unit is performing a test
Flashing Red (Continuous) Electronics failure
Flashing Red (Slow) Battery Failure
Double Flashing RedLoad Failure
Status
Test Type
Quick Test Press and Hold
60-Second Test 2 X Press and Release
90-Minute Test 3 X Press and Release
Load Calibration 4 X Press and Release
Cancel 90-Minute Test 1 X Press and Release
TCTS Button Sequence
Table 1: TCTS Self Diagnostic Status Codes
Table 2: TCTS Manual Test Sequences
Rev. 2108
68E20-109
In case of multiple failures only the highest priority failure will be
indicated. Charge Failure is the highest priority failure, followed by
Battery Failure, followed by Load Failure.
Replacement
Disconnect the unit connector and ensure that AC power is o󰀨 before replacing an ILB CP20 HE AELR. If the model features quick
disconnect terminals, mate similar colored wire terminals to install replacement.

Addendum Insert
CP Series Compatibility and Suitability of Use Guidelines
Addendum (Rev.11042014)
The purpose of this addendum is to su󰀩ciently identify electrical compatibility and predictable emergency light output of
the LED luminaire when used with the IOTA ILB CP Series LED emergency drivers. Verication of these operating traits
does not constitute a code-compliant, as-installed emergency egress system. It is still the responsibility of the Designer/
Specier to assure appropriate light levels are achieved during emergency operation of the luminaire in accordance with
Federal, state and local municipal codes regarding path of egress illumination.
1. Determining Electrical Compatibility
1.1 Verify Class 2 compliant driver per driver manufacture specications.
1.2 Verify that the Emergency Driver (ILB CP Series) selected does not exceed the power delivered to the LED
array (voltage and current) of the normal driver.
2. Calculating Lumen Output During Emergency Operation
2.1 Assess luminaire/xture data.
2.1.1 DESIGNLIGHTS CONSORTIUM
- Log onto the DesignLights Consortium website (www.designlights.org).
- Click on “search the DLC Qualied Product List” button on the DLC homepage.
- In the “search by keyword” text window enter: luminaire manufacturer name and part number.
- Click on “Search” tab to open the “Qualied Products List.”
- Determine per “RATED DATA” e󰀩cacy shown in lumens per watt - (lm/w).
- Multiply lumens per watt by ILB-CP rated output (example: lm/w x 5 watts). Refer to table “ILB
MODEL SPECIFICATION CHART” below for the wattage of the specic ILB CP model to be
used in the luminaire. (lm/w) x (ILB CP Watts) = Minimum emergency lumens of xture.
- Determine per “RATED DATA” the “wattage of the luminaire”.
3. Determining Adequacy of Means-of-Egress Lighting Levels
3.1 Follow industry standards by utilizing available .ies les and lighting design software for your dedicated
emergency luminaires, with the above calculated emergency lumens, and validate your as-installed
plans in accordance with the applicable life safety codes governing your project.
While the ILB-CP series has been found compliant with the requirements of UL Standard 924, it is
ultimately the responsibility of the Designer/Specier to assure the as-installed system delivers code-
compliant path of egress illumination in accordance with Federal, State or local municipal requirements.
ILB CP05
ILB CP07
ILB CP10
5 WATTS
7 WATTS
10 WATTS
ILB MODEL SPECIFICATION CHART
OUTPUT POWER (CONSTANT)
ILB CP12 12 WATTS
ILBSL CP05
ILBSL CP07
ILBSL CP10
5 WATTS
7 WATTS
10 WATTS
ILBSL CP12 12 WATTS
ILB CP20 20 WATTS
ILB CP30 30 WATTS
ILB CP18 18 WATTS
ILBSL CP08 8 WATTS
Rev. 2108
68E20-109