Tews Technologies TPMC917-10 User manual

The Embedded I/O Company
TPMC917
4 MB SRAM with Battery Backup
and 4 Channel RS232
Version 1.0
User Manual
Issue 1.0.7
November 2008
TEWS TECHNOLOGIES GmbH TEWS TECHNOLOGIES LLC
Am Bahnhof 7
25469 Halstenbek, Germany
www.tews.com
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
9190 Double Diamond Parkway,
Suite 127, Reno, NV 89521, USA
www.tews.com
Phone: [phone]
Fax: [phone]
e-mail: [email protected]

TPMC917 User Manual Issue 1.0.7 Page 2 of 26
TPMC917-10
4 MB SRAM module with battery backup and 4
channel RS232
TPMC917-20
4 MB SRAM module with battery backup
TPMC917-21
2 MB SRAM module with battery backup
This document contains information, which is
proprietary to TEWS TECHNOLOGIES GmbH. Any
reproduction without written permission is forbidden.
TEWS TECHNOLOGIES GmbH has made any
effort to ensure that this manual is accurate and
complete. However TEWS TECHNOLOGIES GmbH
reserves the right to change the product described
in this document at any time without notice.
TEWS TECHNOLOGIES GmbH is not liable for any
damage arising out of the application or use of the
device described herein.
Style Conventions
Hexadecimal characters are specified with prefix 0x,
i.e. 0x029E (that means hexadecimal value 029E).
For signals on hardware products, an ‘Active Low’ is
represented by the signal name with # following, i.e.
IP_RESET#.
Access terms are described as:
W Write Only
R Read Only
R/W Read/Write
R/C Read/Clear
R/S Read/Set
©2000-2008 by TEWS TECHNOLOGIES GmbH

TPMC917 User Manual Issue 1.0.7 Page 3 of 26
Issue Description Date
1.0 First Issue September 2000
1.1 General Revision May 2003
1.2 Added Security Warning (Lithium Battery) August 2004
1.3 TPMC917-20 added March 2005
1.4 PCI Class Code changed, PCI Header and EEPROM
Correction June 2005
1.5 New address TEWS LLC September 2006
1.6 TPMC917-21 added
Correction in “Interrupt Status Register” description July 2008
1.0.7 Changed / Corrected PCI9030 Configuration PROM settings
User Manual Issue Notation changed November 2008

TPMC917 User Manual Issue 1.0.7 Page 4 of 26
Table of Contents
1PRODUCT DESCRIPTION.........................................................................................6
2TECHNICAL SPECIFICATION...................................................................................7
3LOCAL SPACE ADDRESSING..................................................................................9
3.1 PCI9030 Local Space Configuration .............................................................................................9
3.2 Local I/O Space ...............................................................................................................................9
3.3 Local Memory Space ....................................................................................................................10
3.3.1 Register Set of each UART channel (TPMC917-10 only) .................................................11
3.3.2 Special Registers...............................................................................................................12
3.3.2.1 FIFO Ready Register Channel 0-3 (TPMC917-10 only)....................................12
3.3.2.2 Interrupt Status Register....................................................................................13
4PCI9030 TARGET CHIP...........................................................................................14
4.1 PCI Configuration Registers (PCR).............................................................................................14
4.1.1 PCI9030 Header TPMC917-10..........................................................................................14
4.1.2 PCI Base Address Initialization..........................................................................................15
4.2 Local Configuration Register (LCR)............................................................................................16
4.3 Configuration EEPROM................................................................................................................17
4.4 Local Software Reset....................................................................................................................18
5CONFIGURATION HINTS........................................................................................19
5.1 PCI Interrupt Control/Status ........................................................................................................19
5.2 Big / Little Endian..........................................................................................................................20
6INSTALLATION........................................................................................................22
6.1 Security Warning (Lithium Battery).............................................................................................22
6.2 Battery Backup Selection.............................................................................................................23
7PIN ASSIGNMENT – I/O CONNECTOR ..................................................................25
7.1 Mezzanine P14 I/O Connector......................................................................................................25
7.2 Front panel DB25 female Connector (TPMC917-10 only) .........................................................26

TPMC917 User Manual Issue 1.0.7 Page 5 of 26
Table of Figures
FIGURE 1-1 : BLOCK DIAGRAM......................................................................................................................6
FIGURE 2-1 : TECHNICAL SPECIFICATION...................................................................................................8
FIGURE 3-1 : PCI9030 LOCAL SPACE CONFIGURATION............................................................................9
FIGURE 3-2 : SRAM MEMORY MAP.............................................................................................................10
FIGURE 3-3 : LOCAL REGISTER MEMORY MAP........................................................................................10
FIGURE 3-4 : REGISTER SET 1 ....................................................................................................................11
FIGURE 3-5 : REGISTER SET 2 ....................................................................................................................11
FIGURE 3-6 : SPECIAL REGISTER...............................................................................................................12
FIGURE 3-7 : FIFO READY REGISTER CHANNEL 0-3................................................................................12
FIGURE 3-8 : INTERRUPT STATUS REGISTER (ADDRESS 0X21)............................................................13
FIGURE 4-1 : PCI9030 HEADER....................................................................................................................14
FIGURE 4-2 : PCI9030 PCI BASE ADDRESS USAGE..................................................................................15
FIGURE 4-3 : PCI9030 LOCAL CONFIGURATION REGISTER FOR TPMC917-10.....................................16
FIGURE 4-4 : CONFIGURATION EEPROM TPMC917-10............................................................................17
FIGURE 5-1 : INTERRUPT CONTROL/STATUS REGISTER (INTCSR, 0X4C)............................................19
FIGURE 5-2 : LOCAL BUS LITTLE/BIG ENDIAN...........................................................................................20
FIGURE 6-1 : DIP SWITCH POSITION..........................................................................................................23
FIGURE 6-2 : DIP SWITCH SETTINGS FOR BATTERY BACKUP BY ON BOARD LITHIUM CELL ...........23
FIGURE 6-3 : DIP SWITCH SETTINGS FOR BATTERY BACKUP VIA P14 I/O CONNECTOR...................24
FIGURE 6-4 : DIP SWITCH SETTINGS FOR BATTERY BACKUP DISABLED............................................24
FIGURE 7-1 : MEZZANINE P14 I/O CONNECTOR.......................................................................................25
FIGURE 7-2 : P14 PIN ASSIGNMENT ...........................................................................................................25
FIGURE 7-3 : FRONT PANEL DB25 FEMALE CONNECTOR (TPMC917-10 ONLY)...................................26
FIGURE 7-4 : DB25 PIN ASSIGNMENT.........................................................................................................26

TPMC917 User Manual Issue 1.0.7 Page 6 of 26
1Product Description
The TPMC917 is a standard single-width 32 bit PMC module providing 4 Mbyte SRAM with battery
backup by an on board lithium cell for all SRAM devises and four ESD protected RS232 channels
(TPMC917-10 only).
The 4 Mbyte NV-SRAM is organized in two banks, each of them provides 512k x 32 bit memory.
During normal operation (standard 5V supply applied to the SRAM) the capacity of the lithium cell is
monitored every 24 hours by the battery monitor device and an interrupt can be generated, if the
battery voltage is too low. The monitor device switches the power supply of the SRAM from the
standard 5V to the battery if the 5V supply drops below the threshold level of the battery monitor
device. Any active access to the SRAM at this point is executed correctly within 1.5µs. After this time
any further accesses to the SRAM are not possible. A miniature DIP switch allows the selection of the
battery backup source either from the on board lithium cell or from an external battery via the P14 I/O
connector.
The TPMC917-10 provides four RS232 channels. Each channel has a programmable baud rate up to
115.2 Kbaud. The 4 channel UART16C654 provides 64 byte transmit FIFO and 64 byte receive FIFO
for each channel to significantly reduce the overhead required to provide data to and get data from the
transmitter and receiver. The FIFO trigger levels are programmable. The channels are ESD protected
up to +/-15kV according to the human body model and IEC1000-4-2.
For applications which do not need the UARTs of the TPMC917-10, the TPMC917-20 provides
4 MByte NV-SRAM and has no UARTs.
The TPMC917-21 has a reduced memory size. It provides 2 MByte NV-SRAM and has no UARTs.
Figure 1-1 : Block Diagram
CAUTION! - This system contains a lithium battery. Lithium batteries may explode if
mishandled.
Please refer to chapter “Security Warning (Lithium Battery)”.

TPMC917 User Manual Issue 1.0.7 Page 7 of 26
2Technical Specification
PMC Interface
Mechanical Interface PCI Mezzanine Card (PMC) Interface
Single Size
Electrical Interface PCI Rev. 2.1 compliant
33 MHz / 32 bit PCI
3.3V and 5V PCI Signaling Voltage
On Board Devices
PCI Target Chip PCI9030 (PLX Technology)
RS232 Interface (TPMC917-10 only)
UART Controller ST16C654 (4 channel UART)
Number of RS232 Channels 4
FIFO 64 byte transmit FIFO
64 byte receive FIFO per channel
Interrupts PCI INTA for all channels, on board Interrupt Status Register
I/O Signals/Channel TX, RX, RTS, CTS, GND
Maximum Transfer Rate Up to 115.2 kbps @2.5nF and 3kohm load impedance
ESD Protection +/-15kV Human Body Model, +/-6kV IEC1000-4-2 model
SRAM Interface
Memory Capacity TPMC917-10/20: 4 Mbyte, 2 banks organized as 512k x 32
TPMC917-21: 2 Mbyte, 1 bank organized as 512k x 32
On Board Battery Type CR2430 Lithium Cell (285mA h capacity)
Battery Fault Voltage 2.6V typical
Battery Lifetime @+25°C: approx. 8 years
@+45°C: approx. 4 years
Caused by self discharching effects
Data Retention Time @+25°C 5 years typical (with a fresh on board CR2430 Lithium Cell)
Minimum Data Retention
Voltage 2.0V minimum
5V Power Failure Threshold 4.37V typical
Max./Min. External Battery
Voltage via P14 I/O 5.5V maximum / 3.0V minimum
I/O Interface
I/O Connector DB25 female connector (TPMC917-10 only)
64 pin Mezzanine P14 I/O

TPMC917 User Manual Issue 1.0.7 Page 8 of 26
Physical Data
+3.3V 177mA typical
+5V 456mA typical (TPMC917-10)
450mA typical (TPMC917-20/21)
+12V 360µA max (no load on serial ports,
TPMC917-10 only)
-12V 360µA typical (no load on serial ports,
TPMC917-10 only)
Power Requirements
Battery
backup 1.6µA typical @+25°C
Temperature Range Operating
Storage 0 °C to +70 °C -55°C to +125°C
MTBF TPMC917-10: 236646 h
TPMC917-20: 238000 h
TPMC917-21: 289000 h
Humidity 5 – 95 % non-condensing
Weight 75 g
Figure 2-1 : Technical Specification

TPMC917 User Manual Issue 1.0.7 Page 9 of 26
3 Local Space Addressing
3.1PCI9030 Local Space Configuration
The local on board addressable regions are accessed from the PCI side by using the PCI9030 local
spaces:
PCI9030
Local
Space
PCI9030
PCI Base Address
(Offset in PCI
Configuration
Space)
PCI
Space
Mapping
Size
(Byte) Port
Width
(Bit)
Endian
Mode Description
0 0x18 MEM 4 MByte
(2 MByte*) 32 Battery Backup
Memory
1 0x1C MEM 64 8 Local Register
Figure 3-1 : PCI9030 Local Space Configuration
* TPMC917-21 has only 2 MByte Battery Backup Memory
3.2Local I/O Space
Not used by the TPMC917

TPMC917 User Manual Issue 1.0.7 Page 10 of 26
3.3 Local Memory Space
The complete SRAM of the TPMC917 is accessible in the memory space of the PMC module.
Address range: PCI Base Address 2 for Local Address Space 0 + (0x00000 to 0x3FFFFF)
PCI Base Address 2+ Description Size (byte) Comment
0x00000 to 0x3FFFFF
0x00000 to 0x1FFFFF Battery backup memory 4M
2M TPMC917-10/20 TPMC917-21
Figure 3-2 : SRAM Memory Map
All local registers of the TPMC917 are accessible in the memory space of the PMC module.
Address range: PCI Base Address 3 for Local Address Space 1 + (0x00 to 0x21)
PCI Base Address 3+ Description Size (byte) Comment
0x00 to 0x07 UART controller channel 0 8
0x08 to 0x0F UART controller channel 1 8
0x10 to 0x17 UART controller channel 2 8
0x18 to 0x1F UART controller channel 3 8
0x20 FIFO Ready Register CH0-CH3 1
TPMC917-10 only
0x21 Interrupt Status Register 1 -
Figure 3-3 : Local Register Memory Map

TPMC917 User Manual Issue 1.0.7 Page 11 of 26
3.3.1 Register Set of each UART channel (TPMC917-10 only)
Each of the four serial channels of the TPMC917-10 is accessed in the PCI memory space by two sets
of registers. Both register sets have a common register, the Line Control Register (LCR). Bit 7 of the
LCR is used to switch between the two register sets of a channel.
Register Set 1 is only accessible if bit 7 of the LCR (PCI Base Address 3 + Channel Offset + 0x03) is
set to ‘0’. After reset Register Set 1 is accessible.
PCI Base Address +
Channel Offset + Read Mode Write Mode Size (bit)
0x00 Receive Holding Register Transmit Holding Register 8
0x01 Interrupt Enable Register Interrupt Enable Register 8
0x02 Interrupt Status Register FIFO Control Register 8
0x03 Line Control Register Line Control Register 8
0x04 Modem Control Register Modem Control Register 8
0x05 Line Status Register (LCR) - 8
0x06 Modem Status Register - 8
0x07 Scratchpad Register Scratchpad Register 8
Figure 3-4 : Register Set 1
To get access to Register Set 2 of the serial channels bit 7 of the LCR must be set to ‘1’. The
Enhanced Feature Registers, Xon-1/2 and Xoff-1/2 registers are only accessible if the LCR is set to
‘0xBF’.
PCI Base Address +
Channel Offset + READ/WRITE Size (bit) Comment
0x00 LSB of Divisor Latch 8 LCR bit 7 set to ‘1’
0x01 MSB of Divisor Latch 8 LCR bit 7 set to ‘1’
0x02 Enhanced Feature Register 8 LCR is set to ‘0xBF’
0x03 Line Control Register (LCR) 8 Always accessible
0x04 Xon-1 Word 8 LCR is set to ‘0xBF’
0x05 Xon-2 Word 8 LCR is set to ‘0xBF’
0x06 Xoff-1 Word 8 LCR is set to ‘0xBF’
0x07 Xoff-2 Word 8 LCR is set to ‘0xBF’
Figure 3-5 : Register Set 2
The TPMC917-20/21 has no UARTs. Write access to these registers of a TPMC917-20/21 has no
effect. Reading these registers of a TPMC917-20/21 returns random data.

TPMC917 User Manual Issue 1.0.7 Page 12 of 26
3.3.2 Special Registers
The TMPC917 provides two special registers. For fast status detection there is a FIFO Status Register
for channel 0 to channel 3, and an Interrupt Status Register for all four channels and the battery
interrupts.
For TPMC917-20/21, only the battery interrupt bits of the Interrupt Status Register carry valid data.
Offset to PCI Base Address 3 Register Name Size (bit)
0x20 FIFO Ready Register CH0-CH3 8
0x21 Interrupt Status Register 8
Figure 3-6 : Special Register
3.3.2.1 FIFO Ready Register Channel 0-3 (TPMC917-10 only)
The FIFO Ready Register FIFORDY1 is a byte wide read only register. The FIFO Ready Register
provides the status of the transmit and receive FIFOs of channel 0 to channel 3. Each TX and RX
channel (0-3) has its own 64 byte FIFO. If any of the TX/RX FIFOs become empty/full, the status bit
associated with the TX/RX function of channel 0-3 is set in the FIFO Ready Register.
For TPMC917-20/21, this register carries random data.
Bit Symbol Description Access Reset
Value
7 RXRDY
Channel 3
6 RXRDY
Channel 2
5 RXRDY
Channel 1
4 RXRDY
Channel 0
RX Ready Bit for channel 0-3
1 = the receiver is ready and is below the programmed trigger
level
0 = the corresponding receive FIFO is above the programmed
trigger level or a time-out has occurred
R
3 TXRDY
Channel 3
2 TXRDY
Channel 2
1 TXRDY
Channel 1
0 TXRDY
Channel 0
TX Ready Bit for channel 0-3
1 = one or more empty locations exist in the corresponding
FIFO
0 = the corresponding transmit FIFO is full. This channel will not
accept any more transmit data.
R
Figure 3-7 : FIFO Ready Register Channel 0-3

TPMC917 User Manual Issue 1.0.7 Page 13 of 26
3.3.2.2 Interrupt Status Register
The Interrupt Status Register is a byte wide read / write register located in the PCI Memory Space
(PCI Base Address 3 + 0x21) and is useful for fast interrupt source detection.
It reflects the interrupt status of the four UART channels and the two Battery Status Interrupts.
The battery interrupts can be enabled and disabled.
Bit Symbol Description Access Reset
Value
7
0
6 Enable
Battery INT
Enable the Battery Monitor Interrupt
00 = Interrupt from battery monitor is disabled.
Any other value enables the Battery Monitor Interrupt.
After reset both battery interrupts are disabled.
Both battery monitor devices generate interrupts on the local
interrupt 2 of the PCI target chip if the monitored battery voltage
(on board Lithium Cell or external battery) is lower than the
specified battery fault voltage.
R/W
0
5 INT Status
Bat2 0
4 INT Status
Bat1
Interrupt Status Battery 1/2
1 = indicates interrupt is pending on corresponding battery
monitor
(TPMC917-21: only “INT Status BAT 1” carries valid data)
R 0
3 Interrupt
Channel 3
2 Interrupt
Channel 2
1 Interrupt
Channel 1
0 Interrupt
Channel 0
Interrupt Status of Channel 0-3
1 = indicates interrupt is pending on channel 0-3
0 = no interrupt on channel 0-3
Each of the four serial channels generates interrupts on the
local interrupt 1 of the PCI target chip.
If the “PCI Interrupt Enable” of the PCI target chip is disabled
(Interrupt Control/Status Register bit 6 is set to ‘0’). This register
can be used as a polling register for interrupts of the four serial
controllers.
Interrupts from the four serial channels can be individual
enabled by the ST16C654 serial controller. After reset all UART
interrupts are disabled.
For TPMC917-20/21, these bits carry random data.
R 0
Figure 3-8 : Interrupt Status Register (Address 0x21)

TPMC917 User Manual Issue 1.0.7 Page 14 of 26
4PCI9030 Target Chip
4.1 PCI Configuration Registers (PCR)
4.1.1 PCI9030 Header TPMC917-10
Write ‘0’ to all unused (Reserved) bitsPCI CFG
Register
Address 31 24 23 16 15 8 7 0
PCI
writeable Initial Values (Hex Values)
0x00 Device ID Vendor ID N 0395 1498
0x04 Status Command Y 0280 0000
0x08 Class Code Revision ID N 088000 0A
0x0C BIST Header Type
PCI Latency
Timer Cache Line Size Y[7:0] 00 00 00 00
0x10 PCI Base Address 0 for MEM Mapped Config. Registers Y FFFFFFE0
0x14 PCI Base Address 1 for I/O Mapped Config. Registers Y 00000000
0x18 PCI Base Address 2 for Local Address Space 0 Y FFC00000
0x1C PCI Base Address 3 for Local Address Space 1 Y s.b.
0x20 PCI Base Address 4 for Local Address Space 2 Y 00000000
0x24 PCI Base Address 5 for Local Address Space 3 Y 00000000
0x28 PCI CardBus Information Structure Pointer N 00000000
0x2C Subsystem ID Subsystem Vendor ID N s.b. 1498
0x30 PCI Base Address for Local Expansion ROM Y 00000000
0x34 Reserved New Cap. Ptr. N 000000 40
0x38 Reserved N 00000000
0x3C Max_Lat Min_Gnt Interrupt Pin Interrupt Line Y[7:0] 00 00 01 00
0x40 PM Cap. PM Nxt Cap. PM Cap. ID N 4801 48 01
0x44 PM Data PM CSR EXT PM CSR Y 00 00 0000
0x48 Reserved HS CSR HS Nxt Cap. HS Cap. ID Y[23:16] 00 00 00 06
0x4C VPD Address VPD Nxt Cap. VPD Cap. ID Y[31:16] 0000 00 03
0x50 VPD Data Y 00000000
Figure 4-1 : PCI9030 Header
PCI Base Address 3 for Local Address Space 1:
0xFFFFFFC0 = TPMC917-10/20
0xFFFFFFE0 = TPMC917-21
Subsystem-ID:
0x000A = TPMC917-10
0x0014 = TPMC917-20
0x0015 = TPMC917-21

TPMC917 User Manual Issue 1.0.7 Page 15 of 26
4.1.2 PCI Base Address Initialization
PCI Base Address Initialization is scope of the PCI host software.
PCI9030 PCI Base Address Initialization:
1. Write 0xFFFF_FFFF to the PCI9030 PCI Base Address Register.
2. Read back the PCI9030 PCI Base Address Register.
3. For PCI Base Address Registers 0:5, check bit 0 for PCI Address Space.
Bit 0 = '0' requires PCI Memory Space mapping
Bit 0 = '1' requires PCI I/O Space mapping
For the PCI Expansion ROM Base Address Register, check bit 0 for usage.
Bit 0 = ‘0’: Expansion ROM not used
Bit 0 = ‘1’: Expansion ROM used
4. For PCI I/O Space mapping, starting at bit location 2, the first bit set determines the size of the
required PCI I/O Space size.
For PCI Memory Space mapping, starting at bit location 4, the first bit set to '1' determines the size
of the required PCI Memory Space size.
For PCI Expansion ROM mapping, starting at bit location 11, the first bit set to '1' determines the
required PCI Expansion ROM size.
For example, if bit 5 of a PCI Base Address Register is detected as the first bit set to ‘1’, the
PCI9030 is requesting a 32 byte space (address bits 4:0 are not part of base address decoding).
5. Determine the base address and write the base address to the PCI9030 PCI Base Address
Register. For PCI Memory Space mapping the mapped address region must comply with the
definition of bits 3:1 of the PCI9030 PCI Base Address Register.
After programming the PCI9030 PCI Base Address Registers, the software must enable the
PCI9030 for PCI I/O and/or PCI Memory Space access in the PCI9030 PCI Command Register
(Offset 0x04). To enable PCI I/O Space access to the PCI9030, set bit 0 to '1'. To enable PCI
Memory Space access to the PCI9030, set bit 1 to '1'.
Offset in Config. Description Usage
0x10 PCI9030 LCR’s MEM Used
0x14 PCI9030 LCR’s I/O Not used
0x18 PCI9030 Local Space 0 Used
0x1C PCI9030 Local Space 1 Used
0x30 Expansion ROM Not used
Figure 4-2 : PCI9030 PCI Base Address Usage

TPMC917 User Manual Issue 1.0.7 Page 16 of 26
4.2 Local Configuration Register (LCR)
After reset, the PCI9030 Local Configuration Registers are loaded from the on board serial
configuration EEPROM.
The PCI base address for the PCI9030 Local Configuration Registers is PCI9030 PCI Base Address 0
(PCI Memory Space) (Offset 0x10 in the PCI9030 PCI Configuration Register Space) or PCI9030 PCI
Base Address 1 (PCI I/O Space) (Offset 0x14 in the PCI9030 PCI Configuration Register Space).
Do not change hardware dependent bit settings in the PCI9030 Local Configuration Registers.
Offset from
PCI Base
Address
Register Value Description
0x00 Local Address Space 0 Range s.b. 4 MB / 2 MB Local memory space
0x04 Local Address Space 1 Range 0x0FFF_FC00 Local register space
0x08 Local Address Space 2 Range 0x0000_0000 Not used
0x0C Local Address Space 3 Range 0x0000_0000 Not used
0x10 Local Exp. ROM Range 0x0000_0000 Not used
0x14 Local Re-map Register Space 0 0x0000_0001 Address offset for memory
0x18 Local Re-map Register Space 1 0x0040_0001 Address offset for registers
0x1C Local Re-map Register Space 2 0x0000_0000 Not used
0x20 Local Re-map Register Space 3 0x0000_0000 Not used
0x24 Local Re-map Register ROM 0x0000_0000 Not used
0x28 Local Address Space 0 Descriptor 0x0082_0100 Local timing address space 0
0x2C Local Address Space 1 Descriptor 0x5401_A0E0 Local timing address space 1
0x30 Local Address Space 2 Descriptor 0x0000_0000 Not used
0x34 Local Address Space 3 Descriptor 0x0000_0000 Not used
0x38 Local Exp. ROM Descriptor 0x0000_0000 Not used
0x3C Chip Select 0 Base Address 0x0010_0001 Chip select lower 2 MB memory bank
0x40 Chip Select 1 Base Address 0x0030_0001 Chip select upper 2 MB memory bank
0x44 Chip Select 2 Base Address 0x0040_0011 UART registers
0x48 Chip Select 3 Base Address 0x0040_0023 Special registers
0x4C Interrupt Control/Status s.b. Interrupt configuration
0x4E EEPROM Write Protect Boundary 0x0000_0000 No write protection
0x50 Miscellaneous Control Register 0x807C_5000 Retry delay = maximum
0x54 General Purpose I/O Control 0x0249_06D3 GP4 is input, all others are outputs
0x70 Hidden1 Power Management data select 0x0000_0000 Not used
0x74 Hidden 2 Power Management data scale 0x0000_0000 Not used
Figure 4-3 : PCI9030 Local Configuration Register for TPMC917-10
Interrupt Control/Status: 0x0000_005B = TPMC917-10
0x0000_005A = TPMC917-20/21
Local Address Space 0 Range: 0xFFFFFFC0 = TPMC917-10/20
0xFFFFFFE0 = TPMC917-21

TPMC917 User Manual Issue 1.0.7 Page 17 of 26
4.3 Configuration EEPROM
After power-on or PCI reset, the PCI9030 loads initial configuration register data from the on board
configuration EEPROM.
The configuration EEPROM contains the following configuration data:
•Address 0x00 to 0x27 : PCI9030 PCI Configuration Register Values
•Address 0x28 to 0x87 : PCI9030 Local Configuration Register Values
See the PCI9030 Manual for more information.
Address Offset
0x00 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0E
0x00 0x0395 0x1498 0x0281 0x0000 0x0880 0x000A s.b. 0x1498
0x10 0x0000 0x0040 0x0000 0x0100 0x4801 0x4801 0x0000 0x0000
0x20 0x0000 0x0006 0x0000 0x0003 s.b. 0x0000 0x0FFF 0xFFC0
0x30 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0001
0x40 0x0040 0x0001 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x50 0x4082 0x0100 0x5401 0xA0E0 0x0000 0x0000 0x0000 0x0000
0x60 0x0000 0x0000 0x0010 0x0001 0x0030 0x0001 0x0040 0x0011
0x70 0x0040 0x0023 0x0000 s.b. 0x807C 0x5000 0x0249 0x06D3
0x80 0x0000 0x0000 0x0000 0x0000 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0x90 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xA0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xB0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xC0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xD0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xE0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
0xF0 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF 0xFFFF
Figure 4-4 : Configuration EEPROM TPMC917-10
TPMC917-10: 0x0C = 0x000A, 0x76 = 0x005B 0x28 = 0x0FC0
TPMC917-20: 0x0C = 0x0014, 0x76 = 0x005A 0x28 = 0x0FC0
TPMC917-21: 0x0C = 0x0015, 0x76 = 0x005A 0x28 = 0x0FE0

TPMC917 User Manual Issue 1.0.7 Page 18 of 26
4.4 Local Software Reset
The PCI9030 Local Reset Output LRESETo# is used to reset the on board local logic.
The PCI9030 local reset is active during PCI reset or if the PCI Adapter Software Reset bit is set in the
PCI9030 local configuration register CNTRL (offset 0x50).
CNTRL[30] PCI Adapter Software Reset:
Value of ‘1’ resets the PCI9030 and issues a reset to the Local Bus (LRESETo# asserted). The
PCI9030 remains in this reset condition until the PCI Host clears this bit. The contents of the PCI9030
PCI and Local Configuration Registers are not reset. The PCI9030 PCI Interface is not reset.

TPMC917 User Manual Issue 1.0.7 Page 19 of 26
5 Configuration Hints
5.1PCI Interrupt Control/Status
The UART and battery status generate interrupts on pin INTA# of the PCI bus. The interrupt status
can be read at the Interrupt Status Register INTCSR of the PCI Controller PCI9030.
Bit Description Access Reset Value
31:8 Not used R 0
7 Software Interrupt R/W 0
6 PCI Interrupt Enable R/W 1
5 Battery Interrupt Status R 0
4 Local Interrupt 2 Polarity R/W 1
3 Local Interrupt 2 Enable R/W 1
2 UART Interrupt Status R 0
1 Local Interrupt 1 Polarity R/W 1
0 Local Interrupt 1 Enable R/W 1 (TPMC917-10)
0 (TPMC917-20/21)
Figure 5-1 : Interrupt Control/Status Register (INTCSR, 0x4C)
The local interrupt 1 reflects the four channel UART interrupts (TPMC917-10 only). Bit 2 will be set if
bit 1 is set and an interrupt is generated on one or more UART channels. For more information see
chapter “Interrupt Status Register”.
The local interrupt 2 reflects the status of the backup battery supply voltage (either on board Lithium
Cell or external battery via P14 mezzanine connector). This register will be initialized from the on
board EEPROM after power-on the TPMC917 with the above shown initial values.

TPMC917 User Manual Issue 1.0.7 Page 20 of 26
5.2Big / Little Endian
•PCI – Bus (Little Endian)
Byte 0 AD[7..0]
Byte 1 AD[15..8]
Byte 2 AD[23..16]
Byte 3 AD[31..24]
•Every Local Address Space (0...3) and the Expansion ROM Space can be programmed to operate
in Big or Little Endian Mode.
Big Endian Little Endian
32 Bit 32 Bit
Byte 0 D[31..24] Byte 0 D[7..0]
Byte 1 D[23..16] Byte 1 D[15..8]
Byte 2 D[15..8] Byte 2 D[23..16]
Byte 3 D[7..0] Byte 3 D[31..24]
16 Bit upper lane 16 Bit
Byte 0 D[31..24] Byte 0 D[7..0]
Byte 1 D[23..16] Byte 1 D[15..8]
16 Bit lower lane
Byte 0 D[15..8]
Byte 1 D[7..0]
8 Bit upper lane 8 Bit
Byte 0 D[31..24] Byte 0 D[7..0]
8 Bit lower lane
Byte 0 D[7..0]
Figure 5-2 : Local Bus Little/Big Endian
Standard use of the TPMC917:
Local Address Space 0 32 bit bus in Little Endian Mode
Local Address Space 1 8 bit bus in Little Endian Mode
Local Address Space 2 not used
Local Address Space 3 not used
Expansion ROM Space not used