texet CC612N User manual

SPECIFICATION
Model: CC612N
Voltage: 220-240VAC,50Hz
Current: 1.0 Amp
Paper entr width: 220mm
Shred size: 4mm x 33mm
Shred paper capacit : 6 x A4 Sheets 70gsm/1 Credit Card
Shred speed: 2.9m/Min
Waste bin Volume: 12L
Noise level: 72 dB
Dut c cle: 2 Mins On/30 Mins Off
Net weight: 3.05Kgs
Dimension: (L x H X D) 290mm x 385 x 140mm
T pe designation:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Test Standards:EN55014-1:2006
EN55014-2:1997+A1:2001
EN61000-3-2:2006
EN61000-3-3:2008
Visit www.texet.com for details on other Texet products.
UK: Waste Electrical products/batteries should not be disposed of with household waste.
Separate disposal facilities exist, for our nearest facilities, see www.rec cle-more.co.uk
or in store for details.
Made in China
Instruction manual
CROSS CUT SHREDDER
CC612N
Please read the following Instructions carefull before use, and keep for future reference.

http://www.texet.com
Thank ou for purchasing the TEXET Cross Cut Shredder, CC612N, with normal use and
maintenance, our shredder will provide ears of satisfactor performance. Please read the
instruction manual carefull and retain for future reference.
To protect this Shredder correctl and avoid an damage, please
ensure ou understand the following Icons:-
Please do not spra an flammable gas, water or oil onto this Shredder.
Please keep children awa from the Shredder, the sharp blades ma harm
them.
Please keep cloths, ties and the like awa from the paper entr slot.
To prevent damage to the cutters remove paper clips, and other
fasteners before shredding.
Please keep our hands out of the paper entr slot as the sharp blades
ma cause injur .
Please keep our hair awa from the shredder/paper entr slot.
The incorrect operation of this appliance ma cause personal injur or damage the
shredder. The Plug Socket outlet should be easil accessible.
BS Plug Fuse – 3A Fitted
GENERAL SAFETY
When using electrical appliance, basic precautions should alwa s be followed to reduce the
risk of fire, electrical shock and injur to persons including the following;
The Shredder is onl intended for private/domestic and small office use. An other uses not
recommended b the manufacture, ma result in the warrant being void. Do not use the
shredder to shred film, OHP Pouches, adhesive stickers, cloths or an plastics, other that
credit cards, as these ma cause damage.
Remove the Shredder from its packaging and check to make sure it is in good condition
before using. Keep the packaging for storage and transportation.
This Shredder is not intended for use b persons, including children, with reduced ph sical,
sensor or mental capabilities, or lack of experience and knowledge, unless the have been
given supervision or instruction concerning the use of the Shredder b a person responsible
for their safet .
Extreme caution is necessar where children or persons with reduced ph sical, sensor or
mental capabilities ma come into contact with the Shredder when in use.
Do not let children pla with parts of the packaging, such as plastic bags.
Ensure the power suppl to the socket into which the Shredder is plugged, is in accordance
with the rating label on the shredder and that the socket is earthed.
Do not use the Shredder if the Power Cord is damaged. If the Power Cord is damaged it
must be replaced b a recognized service agenc or other qualified person.
Alwa s turn the Power off before unplugging the Shredder and make sure our hands are
dr to prevent electric shock.
Do not use outdoors.
Alwa s unplug the Shredder when not in use.

Setup:
1. Remove the shredder from the outer carton.
2. Place the shredder head onto the bin. If the shredder head does not make complete
contact with the basket, then the device will not operate.
Shredder Capacit :
The CC612N will shred 6 sheets of A4 70g paper at once or 1 Credit Card, and will accept
paper width up to 220mm.When shredding smaller items like envelopes or credit card
receipts, insert them through the middle of the feed slot, there is a separate slot for Credit
Cards.
The paper sensor is located in the centre of the main feed slot. When paper is inserted, the
sensor starts the cutters. When the paper has gone through the shredder, the sensor will
switch the cutters off.
Operating the Shredder:
1. Prepare the paper to be shredded b removing paper clips, staples and an other
objects that ma jam in the feed slot
2. Onl feed 6 sheets of 70g A4 paper at an one time or 1 Credit Card.
3. Set the select switch on top of the shredder to AUTO, OFF or REV position for the
desired operation
AUTO : Activates the auto shred function, the shredder will start automaticall when an item
is inserted into the paper feed slot and will stop once the paper has been shredded.
REV : Reverses the shredding direction and backs the paper out of the shredder, in the event
of a paper jam.
OFF : This position is recommended when empt ing the shredder bin or when the shredder
is not in use for a prolonged period of time.
The Waste Bin has a Stabilit Lever on the bottom of the Waste Bin, (at the back), pull this
out to give the Waste Bin extra stabilit .
Paper Jams:
The CC612N is equipped with a motor overload protection device - the normal short dut
c cle for continuous shredding at maximum capacit , is 2 minutes on & 30 minutes off. The
power ma terminate automaticall in case of the following situations:
1. Operating the shredder at maximum capacit continuousl for a prolonged period of
time, e.g. more than 2 minutes without stopping.
2. Exceeding the shredding capacit e.g. inserting more than 6 sheets at one time, or if the
paper is not fed squarel into the feed slot.
Both of these operations ma result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs, ou should:
1. Unplug the power cord from the AC outlet and wait at least 30 minutes for the overload
protection to reset. Tear or cut off an excess paper from the top of the shredder.
2. Plug the power cord back into the AC outlet and place the switch in REV. Pull the
remaining paper out of the cutters. Place the switch back to the AUTO position if
necessar .
3. With the switch in the AUTO position and the feed slot clear, ou are now read to
resume normal shredding.
If the shredder overheats a red light will appear and the shredder will automaticall shut off, it
will restart once the motor has cooled down, this normall takes at least 30 minutes.
Clearing the Blades of Paper Jams
If paper becomes jammed during shredding, move the switch to reverse, this will back out
the jammed paper. Move the switch to off then pull out the jammed paper from the feed slot.
Move the switch across to REV for approx.5-10 secs, this should ensure an paper still in the
blades is completel shredded. Move the switch back to Auto, ou are now read to continue
shredding
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.
DO NOT, UNDER ANY CIRCUMSTANCES, INSERT METAL OBJECTS INTO THE ENTRY
FEED SLOT OR THE BLADES, TO REMOVE THE JAMMED PAPER.
Maintenance
Warning:
When ou want to maintain the shredder, please make sure ou have switched off the
shredder and removed the plug from its socket.
 Use a dr soft cloth when ou want to clean the shredder.
 The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinners to avoid fading or scratches.
 Do not allow water to enter the shredder head when cleaning.
 To maintain the qualit of our shredder blades please use Texet LB12 lubricating
sheets once a month.
 Waste Empt ing:
1. When ou empt the waste bin, please make sure the unit is switched off and unplugged
2 Place the shredder head back onto the bin correctl .
Paper is easil wrapped around the shredder head if the waste bin is allowed to get
too full, therefore please empt the waste bin after shredding 60 A4 Sheets.
Disposal:
Please dispose of this product responsibl at an approved disposal site or rec cling facilit .
Do not dispose of this product in household waste.

TROUBLE SHOOTING
Troubles Reason Solution
Shredder does
not work after
paper is
inserted.
1. The power cord ma not be
properl connected.
2. The motor has been over
heated
.
3. The paper feed ma be
jammed.
4. Shredder head is not placed
properl on basket.
1. Check the power cord is correctl
plugged in both the plug socket and the
shredder.
2. Wait for about 30 minutes and tr the
shredder again.
3. Put switch in reverse, back paper out,
switch off. Remove excess paper, switch
to reverse for 5-10secs, to clear an
jammed paper then switch to Auto and
carr on shredding
4. Place shredder head securel on
basket, correctl front facing, ensuring
contact with the basket is made.
Shredder does
not stop after
shredding has
finished
1. The mechanical sensor ma
be jammed b paper
1. Clean the paper entr and tr again,
ensuring ou remove the plug from the
socket first.
Shredder makes
a high noise
1. The shredder ma not be
placed on a flat/stable surface.
1.Replace the shredder onto a flat/stable
surface.
Shredder does
not shred paper
1. Too much paper is inserted.
2. The paper size inserted ma
be larger than the paper entr .
3. The paper ma be inclined
when placed into the paper
entr .
1. Check to see if ou have exceeded
the rated capacit of paper (6 sheets of
70 g).
2. Reverse the shredder and take out
the paper, fold in half and tr again.
3. Re-insert the paper verticall .