Shredder Capacit :
The CD1912 will shred 12 sheets of A4 70g paper at once, 1 Credit Card or 1 CD/DVD and
will accept paper width up to 220mm.When shredding smaller items like envelopes or credit
card receipts/, insert them through the middle of the feed slot. Please note there Is a
separate slot for Credit Cards and CD/DVD’s.
The paper sensor is located in the centre of the main feed slot. When paper is inserted, the
sensor starts the cutters. When the paper has gone through the shredder, the sensor will
switch the cutters off.
Operating the Shredder:
1. Prepare the paper to be shredded b removing paper clips and an other objects that
ma jam in the feed slot.
2. Onl feed 12 sheets of 70g A4 paper at an one time or 1 Credit Card or 1 CD/DVD.
3. Set the select switch on top of the shredder to AUTO, OFF or REV position for the
desired operation
AUTO
: Activates the auto shred function, the shredder will start automaticall when an item
is inserted into the paper feed slot and will stop once the paper has been shredded.
OFF
: This position is recommended when empt ing the shredder bin or when the shredder
is not in use for a prolonged period of time.
REV
: Reverses the shredding direction and backs items out of the shredder in the event of a
paper jam.
Paper Jams:
The CD1912 is equipped with a motor overload protection device, the normal dut c cle for
continuous shredding at maximum capacit , is 2 minutes on & 30 minutes off. The power
ma terminate automaticall in case of the following situations:
1. Operating the shredder at maximum capacit continuousl for a prolonged period of
time, e.g. more than 2 minutes without stopping.
2. Exceeding the shredding capacit e.g. inserting more than 12 sheets at one time, or if
the paper is not fed squarel into the feed slot.
Both of these operations ma result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs, ou should:
1. Unplug the power cord from the AC outlet and wait at least 30 minutes for the overload
protection to reset.
2. Plug the power cord back into the AC outlet and place the switch in REV. Pull the
remaining paper out of the cutters. Place the switch back to the AUTO position if
necessar .
3. With the switch in the AUTO position and the feed slot clear, ou are now read to
resume normal shredding.
If the shredder overheats, the red overheat light will come on and it will automaticall shut
down, it will restart again after 30 minutes, once the shredder has cooled down
Clearing the Blades of Paper Jams
If paper becomes jammed during shredding, move the switch to reverse and remove an
excess paper from the feed slot. Move the switch back to auto and see if this clears the jam,
If not move the switch alternatel between REV and Auto 2-3 times, this should clear the
paper jam. Put the switch back to Auto and carr on shredding.
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.
DO NOT, UNDER ANY CIRCUMSTANCES, INSERT METAL OBJECTS INTO THE ENTRY
FEED SLOT OR THE BLADES, TO REMOVE THE JAMMED PAPER.
Maintenance
Warning:
When ou want to maintain the shredder, please make sure ou have switched off the
shredder and removed the plug from its socket.
Use a dr soft cloth when ou want to clean the shredder.
The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinners to avoid fading or scratches.
Do not allow water to enter the shredder head when cleaning.
To maintain the qualit of our shredder blades please use Texet LB12 lubricating
sheets once a month.
Waste Empt ing:
1. When ou empt the waste bin, please make sure the shredder is switched off and
unplugged.
2. Place the shredder head back onto the bin correctl .
