The Handy THMLS Installation and maintenance instructions

2013-04-03
OPERATOR’S MANUALAND PARTS LIST
8 Ton Manual Logsplitter - THMLS
Spares & Support: 01793 333212
www.thehandy.co.uk
Before use please read & understand this manual, paying particular attention to the safety instructions.

2013-04-03
2
*** READ ALL WARNINGS BEFORE OPERATION!***
Always wear safety glasses when using this log splitter!
Tie back long hair, roll up sleeves and remove any loose clothing, jewellery or gloves to prevent
them getting caught in moving parts.
This log splitter is only intended to be used to split logs!
Serious injury may occur if this log splitter is used for any other purpose than its intended use.
PLEASE READ PRIOR TO OPERATION:
1. Read and understand this entire instruction manual before using this log splitter.
2. Always wear safety glasses when using this log splitter to avoid damage to your eyes from
flying wood pieces.
3. Never place your hands or other body parts on or near the log, wedge, hydraulic ram, or
splitter workbench while splitting the log.
4. Do not use this log splitter for any other purpose other than splitting logs. Do not use this log
splitter beyond its 8 ton capacity.
5. Never leave the log or splitter under pressure.
6. Keep the area around the log splitter clear of any bystanders to prevent injury from ejected
wood pieces.
7. Always clear away wood pieces from the log splitter and the area around it before starting on
another log.

2013-04-03
3
ASSEMBLY:
Place log splitter horizontal or vertical on floor in a clear and level area. Refer to the parts list for
the following steps:
Step 1: Attach The Handles
Attach handles (part #8) to the top of the log splitter. One handle on each side. Secure each
handle using a Lock Washer Ø10 (part #20) and M10 Hex Nut (part #21).
Step 2: Attach The Hydraulic Pump
Assemble the hydraulic pump (part #12) to the base by using two inner hex screws M8x16 (part
#14). Note you should use an inner hex wrench to assemble this pump.

2013-04-03
4
Step 3: Attach The Base Feet
Attach the Base Feet (part #22) to the bottom of the main post near the hydraulic pump as shown
in Step 3. One foot on each side. Secure each foot using two M10X25 Hex Bolts (part #19), two
Lock Washers Ø10 (part #20) and two M10 Hex Nuts (part #21).
NOW POSITION LOG SPLITTER VERTICALLY ONTO FEET
Step 4: Attach The Foot Pedal
Insert foot pedal (part #5) into hydraulic pump slot. Tighten hex bolt M6x10 (part #6) to secure
the foot peddle to the hydraulic pump. See parts illustration.

2013-04-03
5
Step 5: Attach The Pull Springs
Attach each pull spring (part #13) into the centre hole of the foot leg first. Then attach the
opposite end to the splitter workbench (part #11). Repeat Step 5 for each spring.
Step 6: Attach The Log Cradle
Attach the log cradle (part #29) to the main post by using a Hex Bolt M6x12 (part #31) and a
Lock Washer Ø6 (part #32).

2013-04-03
6
OPERATION:
1. Cut the logs for splitting to 23” or less to fit into the splitter.
2. To enable the hydraulic jack ram -- pump the foot pedal of the hydraulic pump to raise the
splitter workbench.
3. Pull both of the wedge release pins out of the holes in the post, and lower the wedge to a
height slightly more than the length of the log.
Note: Make sure the wedge release pins are firmly seated in the post holes before
continuing.
4. Place the log securely on the splitter workbench.
5. Keeping the log stable and your hands out of the way of the wedge, use the hydraulic foot
pedal to raise the log up tight against the wedge.
6. Keep your hands away from the log and log splitter, continue with even strokes of the
hydraulic foot pedal until the log is split.
7. Remove the wood pieces and clear the area of any debris.
8. To lower the splitter workbench first release the hydraulic pump by treading on the release
lever on the jack, then apply downward pressure to the workbench.

2013-04-03
7
STORAGE:
Store the log splitter in a dry location with the pressure released by treading the release lever.
MAINTENANCE:
Wipe down the log splitter to remove any tree sap or dirt after each use. Occasionally, you may
need to add hydraulic oil to maximise performance.
To add oil to the hydraulic pump:
Note: Refer to the Parts Breakdown to identify the parts named below.
1. Remove the pull spring, then separate the workbench from hydraulic pump.
2. Use a 6mm inner hex wrench to remove the two inner hex screws that hold the hydraulic pump
to the base.
3. Position the pump horizontally and remove the round rubber oil plug on the back of the pump
housing.
4. Add ISO VG15 hydraulic oil until the cylinder is approximately 3⁄4 full. (Oil weight is
approximately 0.7kg/1.543lbs)
5. Replace the rubber oil plug and reassemble the log splitter.

2013-04-03
8
8 TON MANUAL LOG SPLITTER
PARTS DIAGRAM

2013-04-03
9
PARTS LIST
NO. WEBB NO. DESCRIPTION QTY
1 TH196-1 Sleeve With Thread 2
2 TH196-2 Pin 2
3 TH196-3 Ring 2
4 TH196-4 Pressure Spring 2
5 TH196-5 Foot Pedal 1
6 TH196-6 Hex Bolt M6x10 1
7 TH196-7 Beam Frame 1
8 TH196-8 Handle 2
9 TH196-9 Inner Hex Screw M6x12 1
10 TH196-10 Wedge Assembly 1
11 TH196-11 Workbench 1
12 TH196-12 Hydraulic Pump 1
13 TH196-13 Pull Spring 2
14 TH196-14 Inner Hex Screw M8x16 2
15 TH196-15 Wheel 2
16 TH196-16 Spacer 2
17 TH196-17 Flat Washer Ø16 2
18 TH196-18 Back Ring Ø17 2
19 TH196-19 Hex Bolt M10x25 4
20 TH196-20 Lock Washer Ø10 6
21 TH196-21 Hex Nut M10 6
22 TH196-22 Base Feet 2
23 TH196-23 Torsional Spring Sleeve 1
24 TH196-24 Torsional Spring 1
25 TH196-25 Extension Rod 1
26 TH196-26 Thin Nut M16 1
27 TH196-27 Release Lever 1
28 TH196-28 Hex Nut M6 1
29 TH196-29 Crandle 2
30 TH196-30 Lock Washer Ø6 4
31 TH196-31 Hex Bolt M6x12 4
32 TH196-32 End Cover 2

2013-04-03
10
EC Declaration of Conformity
We, Importer
Handy Distribution
SN3 4NS
Declare that the product
Designation: Manual 8 Ton Logsplitter
Model: THMLS
Complies with the following directives:
2006/42/EC - Machinery Directive
The conformity assessment procedure followed was in accordance with
Directive 2006/42/EC
Name of the Notified Body: Ente Certificazione Macchine Srl.
Address: Via Mincio, 386 – 41056 Savignano s/P. (MO) – Italy – R.I. 48198
Standards and technical specifications referred to:
EN609-1+A2:2009, EN14121-1:2007, EN ISO 12100-1:2003/A1:2009,
EN ISO 12100-2:2003/A1:2009
Authorised signatory and technical file holder
Date: 03/04/2013
Signature:
Name / title: Mr. Simon Belcher / Managing Director
Hobley Drive, Stratton St Margaret, Swindon, Wiltshire, SN3 4NS.

2013-04-03
11

2013-04-03
12
To order spare parts and see the complete range of garden machinery
and garden equipment from Handy, visit:
www.thehandy.co.uk
Spares & Support: 01793 333212