The Handy THTS175 User manual

V1 21-05-2019
175LB (88L)
TOWED SPREADER
MODEL NO: THTS175 -- PRODUCT NO: 1938209001
EN - ORIGINAL INSTRUCTIONS
ASSEMBLY REQUIRED - MINIMUM TWO PERSONS
SAVE THESE INSTRUCTIONS
SPARES & SUPPORT: 01793 333212
FOR YOUR SAFETY
Please read & understand this manual, payingattention to the safety instructions, before use.
Incorrect use of the product could put the operator or machine in danger.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, our
policy of continuous improvement determines the right to make modifications without prior warning.
Images used are for illustration purposes only
INSTRUCTION MANUAL

Copyright Notice
Copyright © Handy Distribution
Permission is granted to reproduce this publication for personal & educational use only.
Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other form or means without
written permission from Handy Distribution.
In all cases this copyright notice must remain intact.

CONTENTS
SPECIFICATIONS
IMPORTANT INFORMATION
GENERAL SAFETY INSTRUCTIONS
ABOUT YOUR MACHINE
COMPONENTS
ASSEMBLY
OPERATION
MAINTENANCE
STORAGE
PARTS DIAGRAM & LIST
WARRANTY
CE DECLARATION OF CONFORMITY
ASSEMBLY IS REQUIRED - MINIMUM TWO PERSONS
This product requires assembly before use. See “Assembly” section for instructions. Because of the
weight and/or size of the trailer, it is recommended that another adult be present to assist with the
assembly. INSPECT ALL COMPONENTS closely upon receipt to make sure no components are missing or
damaged.
If you require assistance with regards to the contents or operation of the machine, please contact us:
TEL: [phone]
EMAIL: [e-mail]
(MON –FRI 8.00AM TO 5.30PM EXCL. BANK HOLIDAYS)

SPECIFICATIONS
The manufacturer reserves the right to change the product specification and livery according to continued
product improvements.
Model
THTS175
Product Number
1938209001
Weight
N.W 24kg
Spread Width
10-12” (305-366cm)
Load Capacity
175lb (88L)
Frame
Steel
Wheel Size
14” (35.5cm)
Hitch Type
Pin
Tyre Pressure
20PSI
(Inflate using manual foot or hand inflation device)
IMPORTANT INFORMATION
INTENDED USE
The product is intended for domestic gardens. This product is not intended for commercial use.
Generally acknowledged accident prevention regulations and enclosed safety instructions must be observed.
Only perform work described in these instructions for use, any other use is incorrect. The manufacturer will
not assume responsibility for damage resulting from such use.
GENERAL SAFETY INSTRUCTIONS
It is important that you read and understand the owner’s manual and labels affixed to the machine. Learn its
application and limitations as well as the specific potential hazards. Retain these instructions for future
reference. The operator is responsible for following the warnings & instructions in this manual and on the
product.
SAFETY SYMBOLS
Read & understand the
operator’s manual for the trailer
and the ride on product used to
pull the trailer before using the
machine. Failure to follow
instructions could result in death
or serious injury.
Risk of Slicing.
Keep hands out of the way of all
moving parts.
Wear gloves to protect your
hands. Wear foot protection at
all times. Wear eye protection to
protect against flying objects.
Safety alert symbol. Used to alert you
to potential personal injury hazards.
Obey all safety messages that follow
this symbol to avoid possible injury.
DANGER
Indicates an imminently
hazardous situation which, if not
avoided, will result in serious
injury.
WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in serious injury.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided,
may result in minor or moderate
injury.
CAUTION
Used without the safety alert symbol
indicates a potentially hazardous
situation which, if not avoided, may
result in property damage.

IMPORTANT SAFETY WARNINGS
TO REDUCE RISK OF INJURY: Before any use be sure everyone using this product reads and understands all
safety instructions and other information contained in this manual.
GENERAL SAFETY
STAY ALERT
Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect
your ability to use it properly. Do not use this machine when you are tired or distracted from the job at hand.
Be aware of what you are doing at all times. Use common sense.
USERS
Do not at any time carry passengers sit or stand on the machine. Do not allow children to play on, stand upon
or climb in the machine. Never allow children or people unfamiliar with these instructions to use the machine.
Local regulations can restrict the age of the operator.
AVOID DANGEROUS CONDITIONS
Work in daylight or in good artificial light; always be sure of your footing on slopes; walk, never run with the
machine; exercise extreme caution when changing direction on slopes; do not work on excessively steep
slopes; use extreme caution when reversing or pulling the machine towards you; do not put hands or feet near
or under rotating or moving parts.
KEEP BYSTANDERS AND CHILDREN AWAY
Keep unauthorised persons a safe distance away from the machine. If approached, stop the machine
immediately. Do not allow children to handle, climb on or use the machine. Keep in mind the operator or user
is responsible for accidents or hazards occurring to other people or their property.
INSPECT YOUR MACHINE
Check all bolts, nuts, and screws for tightness before each use, especially those securing guards and drive
mechanisms. Vibration during use, may cause these to loosen.
Form a habit of checking to see that all other tools/equipment are removed from the working area before
turning it on. Replace damaged, missing or failed parts before using it. Warning labels carry important
information. Replace any missing or damaged warning labels.
DRESS PROPERLY
Do not wear loose clothing, gloves, scarfs, neckties or jewellery (rings, wrist watches), which can be caught in
moving parts. Always wear long trousers. Always wear substantial non slip, substantial or heavy-duty safety
footwear are highly recommended when working. Never operate barefoot or when wearing sandals. Wear a
face or dust mask if the operation is dusty. Always wear safety glasses/goggles and/or face shields. Everyday
eyeglasses have only impact resistant lenses; they are not safety glasses/goggles. Wear protective hair
covering to contain long hair, preventing it from getting caught in machinery.
DO NOT OVERREACH
Keep proper footing and balance at all times when using the machine. Use on slopes with great care. Never
stand on the machine. Serious injury could occur if the machine is tipped or if the moving parts are
unintentionally contacted. Do not store anything above or near the machine, where anyone might stand on
the machine to reach them.
AVOID INJURY FROM UNEXPECTED ACCIDENT
Keep hands & feet out of the way of all moving parts. Do not place any part of your body or any tool e.g. in the
machine during operation.
DO NOT FORCE TOOL
Always work within the rated capacity. Do not use machine for a purpose for which it was not intended. Before
operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner’s manual concerning safe
operation on slopes. Stay off steep slopes! Always operate at reduce speed in rough terrain, along creeks,
ditches and on hillsides. Do not operate close to creeks, ditches and public highways. To avoid personal injury
and/or equipment damage DO NOT EXCEED 5 MPH. Always use caution when loading and unloading the cart.
Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). Always secure and lock dump cart to
the vehicle hitch before operating.
NEVER LEAVE MACHINE RUNNING UNATTENDED
Do not leave the machine unattended until it has come to a complete stop.
TYRE INFLATION
Tyre pressures must always be inspected prior to each use. Do not over inflate and always use a manual foot

or hand pump. DO NOT EXCEED 20PSI.
INSPECT
Before using, always visually inspect to see that the tools are not worn or damaged. Replace worn or damaged
elements and bolts in sets, to preserve balance.
MAINTAIN YOUR MACHINE WITH CARE
Clean the machine immediately after use. Keep the machine clean to ensure it operates to it’s full and safest
performance. When maintaining this machine, only the manufacturer’s original replacement parts should be
used. The use of non-original manufacturer parts may invalidate your warranty.
PROTECT THE ENVIRONMENT
Take left over materials to an authorised collection point or follow the stipulations in the country where the
machine is used. Do not discharge into drains, soil or water.
STORE IDLE EQUIPMENT
When not in use, the machine should be stored in a dry location. Keep the machine away from children and
others not qualified to use it. Keep away from direct sunlight.
WARNING
The warnings, cautions, and instructions outlined in this instruction manual cannot cover all possible
conditions or situations that may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product and must be supplied by the operator.
ABOUT YOUR MACHINE
This heavy-duty tow-behind lawn spreader makes work a breeze. The steel and nylon construction are durable
and lightweight, making it wear and rust-resistant, easy to tow, and easy to clean. The tow-behind spreader
features a one-handed lever to adjust the spreading rate. It can be stored in a shed or garage with minimal
space. The large hopper makes loading and unloading fast and convenient.
1.
Hopper
Holds up to 175lb (88L)
3.
Tyres
Pneumatic tyres (DO NOT OVER INFLATE)
2.
Adjuster Plate Lever & Gauge
Adjusts the
4.
Hitch
Pin style; use only with approved vehicles.
1
4
3
2

COMPONENTS
This product must be assembled correctly before use. Carefully remove the product and any accessories from
the carton. Inspect the product carefully to make sure there are no breakages or damage occurred during
shipping. Do not discard the packing material and carton until you have carefully inspected and satisfactorily
operated the product.
Take all parts out of the shipping crate and inspect components to ensure there are no missing pieces before
starting to assemble the spreader.
If you require assistance with regards to the contents or operation of the machine, please contact us:
TEL: [phone]
EMAIL: [e-mail]
(MON –FRI 8.00AM TO 5.30PM EXCL. BANK HOLIDAYS)
WARNING
If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed
this warning could result in serious personal injury.
Do not attempt to modify this product or create accessories not recommended for use with this product.
Any such alteration or modification is misuse and could result in a hazardous condition leading to possible
serious personal injury.
Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment
could result in serious injury to the user or bystanders, or cause equipment damage.
Hex Bolt M6x20
x2
Hex Bolt M6x35
X1
Hex Bolt M6x45
X3
Hex Bolt M6x50
x7
Hex Bolt M8x45
X2
Nylock Nut
M6 x13
Nylock Nut
M8 x3
Large Flat
Washer Ø6 x9
Flat
Washer Ø8 x1
Flat Washer
Ø16 x6
Cotter Pin
Ø4x40 x2
R-Clip Ø3x75
x9
Wheel Spacer
x2
Drive Pin Ø6x45
x1
Drive Pin Ø9x60
x1

ASSEMBLY
Before assembling the towed spreader, lay out all of the parts and hardware as shown on the previous
pages.
STEP 1
In the following order put flat washer Ø16, wheel spacer, second flat washer Ø16, Tire, third flat washer Ø16
on the end of wheel axle. Insert the cotter pin Ø4x40 into the small hole on the axle and bend to secure.
Rotate the wheel so that the hole on the inside of the wheel is aligned with the hole on the axle, then Insert
drive pin Ø6x45 and lock it.
Chassis
x1
Hopper
x1
Gauge Assembly
x1
Hitch Arm
x1
Hitch Brace
X4
Support Rod
x1
Wheel & Tyre
Assembly x2
Hopper Screen
x1
Rain Cover
x1
Hitch Bracket
x1
Cotter Pin
Ø4x40
Chassis
Drive Pin Ø6x45
Wheel & Tyre
Assembly
Flat Washer
Ø16
Wheel Spacer
Flat Washer
Ø16

STEP 2
In the following order put flat washer Ø16, wheel spacer, second flat washer Ø16, Tire, third flat washer Ø16
on the end of wheel axle. Insert the cotter pin Ø4x40 into the small hole on the axle and bend to secure.
STEP 3
Insert the hex bolt M6x50 after aligning the hole on the flat end of hitch tongue (stay on top) with the one at
the middle of crossover tube. Connect using a large flat washer Ø6 and nylon lock nut M6 and don’t screw it up
moderately.
Cotter Pin Ø4x40
Wheel & Tyre
Assembly
Wheel Spacer
Flat Washer
Ø16
Hex Bolt
M6x50
Hitch
Arm
Large Flat
Washer Ø6
Nylock Nut
M6

STEP 4
Attach the braces on each side of hitch tongue using bolt M6x45 and nylon lock nut M6. Loosely tighten.
STEP 5
Attach the gauge & lever assembly to the middle of Hitch Tongue using two hex bolts M8x45 and nylon lock
nuts.
Hitch Brace
Hex Bolt M6x45
Nylock Nut
M6
Gauge Assembly
Hex Bolt M8x45
Nylock Nut M8

STEP 6
1. Attach the two upper braces on each side of the gauge & lever assembly using hex bolt M6x45 and nylon
lock nut M6. Loosely tighten.
2. Connect other four end of the braces to the upper mounting tube using bolt M6x45 and nylon lock nut
M6.
3. Tighten all hardware.
STEP 7
1. Align all the six holes around inside of hopper and frame and attach using bolts M6x50, big flat washer Ø 6
on the top and secure with nylon lock nuts M6 on the bottom. Adjust parts the so the impeller moves
freely and tighten the hardware holding the hopper.
2. Insert the R pin Ø3x75 into the hole on the swivel axle.
Hex Bolt M6x45
Hex Bolt
M6x45
Nylock
Nut M6
Hitch Brace
Hex Bolt M6x35
Hex Bolt M6x35
Big Flat
Washer Ø6
Hopper
R Pin Ø3x75
Nylock
Nut M6

STEP 8
Install one flat washer Ø8 on the end of connection rod and insert into the hole on the rod base and secure
using a nylon lock nut M8.
STEP 9
Attach the support rods to the hopper using the hex bolts M6x20, big flat washers Ø6 and nylon lock nuts M6.
STEP 10
Insert the hopper screen into the bottom of the hopper.
Adjust
Connection
Rod
Flat Washer Ø8
Nylock Nut M8
Big Flat
Washer Ø6
Nylock
Nut M6
Hex Bolt M6x20
Support Rod
Hopper Screen

STEP 11
Connect hitch bracket to hitch tongue using the drive pin Ø9x60.
NOTE: Hitch Tongue is adjustable to different lengths.
STEP 12
Before operating the tow behind spreader make sure all hardware is securely tightened.
(*) Push the adjustable handle on Gauge & Lever assembly to the proper setting while spreading.
(*) Push the adjustable handle on Gauge & Lever assembly to the lowest position to stop spreading.
Drive Pin Ø9x60
Hitch Bracket
Hitch Tongue

OPERATION
WARNING
Before using the spreader, review the instructions below and safety information. Failure to follow these
instructions may result in property damage or injury to the operator or bystanders.
USING YOUR SPREADER
Exercise caution at all times when using power equipment.
•Read this owner’s manual carefully for operating and service instructions before attempting to assemble
or operate this equipment. Be thoroughly familiar with the proper use of this equipment.
•Read the vehicle owner’s manual and vehicle safety rules, and know how to operate the vehicle before
using this equipment.
•Never allow children to operate the tractor or lawn sweeper attachment, and do not allow adults to
operate without proper instructions.
•Always handle with care (wear gloves) and wear substantial footwear when operating this spreader.
•Do not allow anyone to ride or sit on spreader attachment frame or on towing vehicle.
•Keep the area of operation clear of all persons, particularly small children and also pets.
•Always begin with the transmission in first (low) gear and engine at low speed, and gradually increase
speed as conditions permit.
•The vehicle braking and stability may be affected with the attachment of this equipment. Be aware of
changing conditions on slopes. Refer to safety rules in the vehicle owner's manual concerning safe
operation on slopes. STAY OFF OF STEEP SLOPES.
•Do not exceed 5MPH
•Tyre pressures must always be inspected prior to each use. Do not over inflate and always use a manual
foot or hand pump. DO NOT EXCEED 20PSI.
•Always operate up and down a slope, never across the face of a slope.
•Always use caution when loading and unloading the hopper.
•Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs).
•Always refer to the vehicle owner’s manual for proper towing.
•Sweeper is not designed to be used with zero-turn mowers.
•Always secure and lock the spreader to the vehicle hitch before operating.
•This equipment should be operated at reduced speed on rough terrain, along creeks and ditches and on
hillsides, to prevent tipping and loss of control. Do not drive too close to a creek or a ditch.
•Do not tow this equipment on a highway or any other public thoroughfare.
•Follow the maintenance instructions as outlined in this owner’s manual.
ATTACH THE SPREADERR TO THE TOWING VEHICLE
On a level surface, line up the towing vehicle with the spreader. Use the hitch pin and insert the R Pin Ø3 to
secure the hitch pin.
TOWING THE SPREADER
Your sweeper is designed to work at speeds of 5mph and lower. You may damage the device or experience
sub-optimal results if exceeding 5mph. Your spreader will work best on flat, smooth surfaces. If operating on a
slope, always tow the sweeper up or down the surface of the hill, not sideways along the slope.

RATE SETTINGS
Our spreaders are designed to spread dry, powdered or granulated materials thinly and evenly over
reasonably smooth surfaces.
•Check the material to be spread packaging for correct spreader settings and application rate.
•Before filling the spreader, ensure the control lever is back to the stop bolt, with the feed-gate closed.
•Ensure that the material is dry and free-running. If in doubt pass it through a sieve with 3mm mesh to
remove lumps.
•When the gauge handle is at 0, the hopper is completely closed. Moving the handle towards 30, the
hopper will gradually open. At 30, the hopper is completely open.
TO GAIN YOUR IDEAL SETTING
•Set rate-setting dial to No 15.
•Fill the hopper approximately 3/4 full.
•Pull the spreader forward on a flat surface (e.g. driveway) and pull the control lever back to the Stop bolt.
If the spread is uneven or inadequate, close the feed-gate and reset the dial to a higher number.
Always move off BEFORE opening the feed-gate and close the gate BEFORE stopping.
•Maximum towing speed 5 MPH.
CAUTION
The rate settings are guidelines only. Even branded materials may vary in grain size, humidity, density etc. If
in any doubt choose a lower setting than that suggested or start at setting no. 2 and adjust as necessary,
until an even spread is achieved.
WARNING
Do not over apply spreading material. Follow the recommended coverage rate for each product. Over
application will lead to damage and contamination. If spreading material accidentally deposits too heavily,
soak the area thoroughly with a garden hose or sprinkler to prevent burning.
CAUTION
DO NOT USE WITH ROCK SALT.
Using rock salt in this spreader will damage the mechanism and shorten the life of the product. Refined ice
melting salt can be used but the user should be aware that this is not a specialised salt spreader and using
salt may corrode the spreader and reduce the life of the machine. Clean the spread thoroughly after using
refined de-icing salt.

CONSISTENT COVERAGE
To ensure consistent coverage, ensure each broadcast pattern slightly overlaps the previous, as shown below.
N.B. ALWAYS MOVE OFF BEFORE OPENING FEED-GATE.ALWAYS CLOSE FEED-GATE BEFORE STOPPING
SUGGESTED SPREADING PATTERNS
MAINTENANCE
WARNING
Improper maintenance and storage of the spreader may void your warranty.
•After each use clean material out of hopper.
•Rinse/dry inside and outside of the spreader after each use.
•Periodically check all fasteners for tightness and replace any damaged fasteners.
•Annually clean and lightly lubricate all moving parts.
•Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.
•Never exceed the hopper load capacity rating.
•Regularly grease axle and wheel bearing area or when needed.
IMPORTANT:
If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement parts
that do not meet specifications may result in a safety hazard or poor operation.
STORAGE
•Be sure to completely empty, clean and dry the spreader hopper before storage.
•Failure to properly clean the spreader & hopper may cause deterioration such as rust or mold.
•Lightly lubricate all moving parts to protect components and prevent rust.
•Store indoors or in a protected area during severe weather and winter months.

PARTS DIAGRAM –THTS175 (1938209001)
NOTE: Parts Lists are
supplied for information
purposes only, not all
parts are stocked
individually & we
recommend you contact
our Spares Team on
01793 333212 for expert
advice.

PARTS LIST –THTS175 (1938209001)
Item
No.
Handy Part
Number
Description
QTY
Item
No.
Handy Part
Number
Description
QTY
1
TH251-930116000
Flat Washer Ø16
6
34
TH251-930206000
Big Flat Washer Ø6
16
2
TH251-N77080000
Pneumatic Tyre
2
35
TH251-C13000004
Nylon Washer
1
3
TH251-N77000006
Wheel Spacer
2
36
TH251-N51200014
Handle Grip
1
4
TH251-N77000007
Bushing
2
37
TH251-N76000012
Adjustable Handle
1
5
TH251-N77000008
Wheel Axle
1
38
TH251-N51000019
Wing Nut
1
6
TH251-N57040002
Gearbox Lower
Cover
1
39
TH251-N51000016
Spacer
1
7
TH251-N57050001
Big Gear
1
40
TH251-N51200027
Connect Plate
1
8
TH251-N57051002
Pinion
1
41
TH251-931508000
Tooth Washer
1
9
TH251-N77000005
Pinion Shaft
1
42
TH251-911406025
Carriage Bolt M6x25
1
10
TH251-N57040001
Gearbox Upper
Cover
1
43
TH251-930108000
Flat Washer Ø8
2
11
TH251-911004020
Screw M4x20
1
44
TH251-N51200009
Swivel Axle Bushing
2
12
TH251-N51200010
Impeller
1
45
TH251-N76010000
Fixed Adjustable
Plate
1
13
TH251-940404040
Cotter Pin Ø4x40
2
46
TH251-N51200022
Active Adjustable
Plate
1
14
TH251-911805015
Screw M5x15
6
47
TH251-N51200024
Fix Plate for Control
Rod
1
15
TH251-T68030000
Drive Pin Ø6x45
1
48
TH251-N51200025
Torsion Spring
1
16
TH251-N51200004
Hitch Support
4
49
TH251-N51200023
Base for Torsion
Spring
1
17
TH251-910106045
Hex Bolt M6x45
3
50
TH251-N77000003
Screen
1
18
TH251-N76000006
Hitch Tongue
1
51
TH251-N77000002
Support Rod
1
19
TH251-N76000007
Support Rod
1
52
TH251-950405013
Rivet
6
20
TH251-910106045
Hex Bolt M8x45
4
53
TH251-910106050
Hex Bolt M6x50
7
21
TH251-920608000
Nylon Lock Nut M8
8
54
TH251-N77000001
Hopper
1
22
TH251-N76000008
Hitch Bracket
1
55
TH251-N76000019
Hopper Frame
1
23
TH251-N51200026
R Pin
2
56
TH251-N76000018
Crossover Tube
1
24
TH251-N10000014
Hitch Plate
1
57
TH251-N57000019
Bushing
1
25
TH251-N77000004
Hitch Pin
1
58
TH251-910106040
Hex Bolt M6x40
2
26
TH251-910108030
Hex Bolt M8x30
2
59
TH251-N77200002
Rain Cover
1
27
TH251-T68020000
Drive Ø9x60
1
60
TH251-N57500014
Thin washer
1
28
TH251-920606000
Nylon Lock Nut M6
19
61
TH251-911804018
Screw M4x18
2
29
TH251-T68000003
End Cap
1
62
TH251-N57540002
Gear Box Top Cover
1
30
TH251-910106035
Hex Bolt M6x35
1
63
TH251-N57040006
Pinion Gland
1
31
TH251-N76000014
Control Rod
1
64
TH251-940203016FH
Elastic Pin
1
32
TH251-910106020
Hex Bolt M6x20
5
65
TH251-911005035
Screw M5x35
1
33
TH251-N57500006
Gauge Plate
1
66
TH251-920605000
Nylon Lock Nut M5
1

GJ HANDY & CO LTD USER WARRANTY POLICY
Users Statement of Warranty
Each new machine is warranted against defective material or assembly of material under normal usage. The
warranty applies to the original purchaser and covers faulty parts and the labour involved in replacing and
repairing those parts, which are of original manufacture.
Period of Warranty
Webb (excludes Electric Handheld, Dynamic, Heritage, Legacy), Webb Pro, Sanli Engine
a) 2 years from the original date of sale to the first domestic user.
b) 90 days from the original date of sale to the professional/commercial user.
c) 90 days from the original date of sale when used for hire.
d) A reduced warranty period of 90 days applies to those items which are subject to normal wear and
tear (e.g. but not limited to wheels, tyres, cutter bars, cylinders, cutting blades, blade boss, belts,
cables, nylon line & spool, collection bags, spark plugs).
e) Engines are supplied with a separate warranty to the machine. The engine manufacturers warranty
statement which will be supplied within the engine instruction manual. All enquiries and warranty
repairs should be discussed with the engine manufacturer or approved warranty repair dealer.
f) 90 days from the original date of purchase for Replacement Spare Parts (unless normal wear & tear
component, which are covered for 30 days).
g) All machines’ must be serviced within the first 12 months from the original date of purchase to
comply with the warranty, failure to do so will invalidate the 2nd year of the warranty.
Webb Electric Handheld, Webb Dynamic, Heritage & Legacy, Handy, Mowerland, Q-Garden
a) 1 year from the original date of sale to the first domestic user.
b) 90 days from the original date of sale to the professional/commercial user.
c) 90 days from the original date of sale when used for hire.
d) A reduced warranty period of 90 days applies to those items which are subject to normal wear and
tear (e.g. but not limited to wheels, tyres, cutter bars, cylinders, cutting blades, blade boss, belts,
cables, nylon line & spool, collection bags, spark plugs).
e) Engines are supplied with a separate warranty to the machine. The engine manufacturers warranty
statement which will be supplied within the engine instruction manual. All enquiries and warranty
repairs should be discussed with the engine manufacturer or approved warranty repair dealer.
f) 90 days from the original date of purchase for Replacement Spare Parts (unless normal wear & tear
component, which are covered for 30 days).
All warranty repairs must be undertaken by an authorised service dealer. These dealers have been accredited
by GJ Handy & Co Ltd and agree to only use genuine parts and follow our repair procedures.
Not covered by this warranty
a) The warranty policy does not cover any depreciation or damages caused by ordinary wear, rusting or
corrosion, lack of correct maintenance or operation, misuse, abuse, lack of transportation or accident.
b) The warranty policy does not cover any costs necessary for the standard periodic maintenance
services instructed by the operator’s manual, or service parts replacement which would include oil,
filters, tyres, belts, brake linings, fuses, blades, seals and other service parts unless it can be proven
that the item has evidence of faulty manufacture.
c) The warranty policy will not cover failure or damage caused as a result of parts or accessories being
modified without the written approval of GJ Handy & Co Ltd.
d) The warranty policy will not cover the unit if non-genuine parts have been fitted and as a result
damage has occurred to the unit.
e) The warranty policy is non-transferable and is only applicable to the original purchaser.

Disclaimer
a) This warranty is only a remedy for defect of products. GJ Handy & Co Ltd will never warranty in terms
of the merchantability or the fitness for a particular purpose.
b) No person is authorised to make any warranties, representations or promises, expressed or implied,
on behalf of GJ Handy & Co Ltd, or to modify the terms conditions or limitation of this warranty policy
in any way.
c) Neither GJ Handy & Co Ltd nor any company affiliated with GJ Handy & Co Ltd shall be liable in any
event or manner whatsoever for incidental or consequential damages or injuries, including, but not
limited to, loss of crops, loss of profit, out of pocket expenses or profits, rental of substitute
equipment or other commercial losses.
General
a) Most warrantable failures show up within the first few weeks of use. These failures are usually
straightforward and warranty assessment is relatively easy.
b) Failures relating to cutter decks and belts need careful investigation, as the cause may not always be
straightforward. Look for damage to blades and pulleys especially when the cutter belt or blade boss
have snapped or cracked as this could be due to impact damage.
c) Customers should always refer to the operator/instruction manual when any disputed problem arises,
you will find most areas covered within the manual.