Neilsen CT2215 User manual

80LB TOW-BEHIND SPREADER CT2215
ORIGINAL INSTRUCTIONS
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Ref no. SP31507

2
EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and
health requirements of the EC Directive based on its design and type, as brought
into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: TWO BEHIND SPREADER
Applicable EC Directives:
EC Machinery Directive 2006/42/EC
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2016-07-05
Model: CT2215 (Ref no. SP31507)
Harmonized standards
EN ISO 12100:2010, EN 349:1993+A1:2008,
EN ISO 14120:2015, EN ISO 13857:2008

3
ASSEMBLY AND OPERATION INSTRUCTION
2. Remove and identify loose parts from carton and bag.
1. SAFETY RULES READ THE DIRECTIONS BEFORE ASSEMBLY
Read the towing vehicle owners manual and towing vehicle safety rules. Know how to
operate your tractor before using the tow-behind spreader.
Read the chemical label instructions and cautions for handling and applying the chemicals
purchased for spreading.
Wear eye and hand protection when handling and when applying lawn or garden chemicals.
Never operate tractor and spreader attachment without wearing substantial footwear, and do
not allow anyone to ride or sit on spreader attachment frame.
Never allow children to operate the tractor or spreader attachment, and do not allow adults to
operate without proper instructions.
Always begin with the transmission in first (low) gear and with the engine at low speed, and
gradually increase speed as conditions permit.
When towing spreader do not drive too close to a creek or ditch and be alert for holes and
other hazards which could cause you to loose control of the spreader and tractor.
Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner’s
manual concerning safe operation on slopes. Stay off steep slopes!

4
STEP1：Install Impeller onto the Gear Box & AxleAssembly. Insert Round Head Bolt M4x20 through impeller
then through Gear Box Axle.

5
iQVHUWWZREROWV0[LQWRWKH)L[LQJ&RQQHFWLQJ5RGWKURXJK:KHHO$VVHPEO\)UDPH0DNHVXUHWKHKROHRQ
$[OHRI*HDU%R[LVWREHRQWKHULJKWVLGHZKHQDVVHPEO\DVVKRZQ$WWDFK:KHHO$VVHPEO\)UDPHVDQG
6XSSRUW/HJRQWR+RSSHUXVLQJEROWV0[ORFNQXWV0DQG%LJ)ODW:DVKHUV1RWH7KHEROWVDQGQXWV
QHHGQWEHWLJKWHQHG\HW
M6x35
STEP 2: $WWDFKWKH:KHHO$VVHPEO\)UDPHRQHDFKVLGHRIWKH*HDU%R[$[OHDQG)L[LQJ&RQQHFWLQJ5RG

6
STEP3：Install one end of the connecting plate on the wheel frame by Bolt M6x35 and Lock Nut M6. Then
install the connecting rod on the wheel frame by Bolt M6x55 and Lock Nut M6 and fixed the connecting plate
with connecting rod by Bolt M6x35. Note: The Bolt and Nuts needn’t be tightened.
Bolt M6x45
Bolt M6x55

7
STEP 4: Insert Inner Axle Bushing into Outer Axle Bushing and make sure they are tight neatly. Install right
Wheel Assembly to right Axle using inner hex bolt M5x45 and lock nut M5, and then install the Cap onto right
Axle using a wooden or rubber hammer. Now install left WheelAssembly to leftAxle, put a flat washer Ø16 and
install the Cap onto left Axle using a wooden or rubber hammer.

8
STEP5: Put the install tube assembly to hopper assembly using Bolt M6x40 and Lock Nut M6.NOW GO
BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT OVER TIGHTEN

9
STEP6: ADJUSTMENTS. When you finished all above steps, You don't need to do the following steps. If
they are not match neatly, you may need to do the following steps. To operate this spreader, push the handle to
the top position (upwards). You may move the position of Wing nut on Gauge & Lever to adjust the spacer of
three holes between hopper and adjustable plate as per your need when spreading.

10
PARTS DRAWING

11
PARTS LIST
Ref.No.
Drawing No.
Description
Qty
1
9114-06025-DG
Carriage Bolt M6x25
1
2
9315-08000-DG
Tooth Washer Ø8
1
3
N570-10000-DG
Gauge & Lever Assembly
1
4
N580-00005-DG
Adjust Handle Pole
1
5
N570-00014
Adjust Handle A
1
6
N570-00015
Adjust Handle B
1
7
9118-04018-DG
Screw M4x18
1
8
N511-00004
Hopper Screen
1
9
N510-00016
Spacer
1
10
N510-00019
Wing Nut M6
1
11
N580-00006
Hopper
1
12
N510-00004
Center Cover
1
13
N570-00017-DG
R Pin Ø2
1
14
9101-06040-DG
Bolt M6x40
4
15
N580-00019
Fixed Plate
1
16
9503-05012
Screw Ø5X12
4
17
N580-00020
Adjustable Plate
1
18
N580-00004
Wheel Frame Assembly (Left)
1
19
N510-00003
Impeller
1
20
N580-00008
Line Clamp Bottom Plate
1
21
9206-05000-DG
Lock Nut M5
5
22
T680-00003
Tube End Cap
5
23
9101-06035-DG
Hex Bolt M6x35
9
24
9110-05010-DG
Round Head Bolt M5x10
2
25
N390-00001-DG
Round Head Pin
1
26
N511-00003
Tow Bar Connect Plate
2
27
N511-00002-DG
Install Tube Assembly
1
28
9499-03000-DG
R Pin Ø3
1
29
9206-06000-DG
Lock Nut M6
18
30
9110-05012-DG
Screw M5X12
2
31
N570-00010-DG
Connect plate
2
32
9101-06055-DG
Bolt M6x55
2
33
N580-00003-DG
Wheel Frame Assembly (Right)
1
34
N511-00005
Pneumatic Wheel
2
35
N511-00001
Connect Rod
2

12
PARTS LIST
Ref.No.
Drawing No.
Description
Qty
36
9105-05045-DG
Inner Hex Bolt M5x45
1
37
N570-00018
Inner Axle Bushing
2
38
N570-00011
Outer Axle Bushing
2
39
N511-30000
Gear Box & Axle Assembly
1
40
9110-04020-DG
Screw M4x20
1
41
9302-06000-DG
Big Flat Washer Ø6
5
42
C130-00004
Nylon Washer
1
43
N580-00009
Line Clamp Press Plate
2
44
N511-20000
Control Rod
1
45
N510-00023
Rain Cover
1
46
N570-00002
Thin Washer
1
47
N580-00011
Big End Cap
1
48
N580-00010
Small End Cap
2
49
N511-40000
Axle End Cover
2
50
9301-16000-DG
Flat Washer Ø16
1
51
N580-00013-DG
Fixing Connecting Rod
1
52
9306-06000-DG
Spring Washer Ø6
1
53
9301-06045-DG
Hex Bolt M6x45
4
CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Made in China