WB Mfg EPIC EP3082-FXO-RR6 User manual

1
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
Before you begin, please make sure all parts and proper quantities are included. (See Part Identier Key) Any parts damaged during shipment must be reported
within 24 hours of receipt. To report information regarding damages or if you have any questions, please call 800.242.2303.
EPIC Ingenuity Table
Assembly Instructions
Step 1:
• Place the EPIC frame leg with plate facing down on a
protected at surface.
Step 2:
• Align holes in the end plate of the cross bar with the
frame. Make sure the tabs on the cross bar are facing
down.
• Connect cross bar to the frame using ¼”-20 x 50mm joint
connector bolts and ¼”-20 joint connector nuts.
• Use a screw gun and a 4mm Hex bit to tighten the joint
connector bolts to the nut. We suggest using a 4mm Hex
wrench to hold the nut in place while tightening the bolt.
• Repeat for other frame leg.
Step 3:
• Place the EPIC Ingenuity top face down on a protected
at surface so threaded inserts and pre-drilled pilot holes
are facing up.
Step 4:
• Place frame leg/cross bar on the top and align with
threaded inserts & pre-drilled pilot holes.
• Using a screw gun and a 4mm Hex bit, secure both frame
legs to top with ¼”-20 x 15mm joint connector bolts. Use
eight bolts for each frame leg.
Step 5:
• Using a screw gun and a # S2 square bit, secure cross bar
to top with #10 x ¾”square pan screws. Use one screw
per tab with a total of six screws being used (3 per side).
EPIC frame leg
Step 1
Step 2Cross bar
Tab
Joint connector bolt
Joint connector nut
V022821 subject to change.
EP3082-FXO-RR6
Step 3
Step 4
Step 5

2
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
EPIC Ingenuity Table
Assembly Instructions
Step 6:
• Before placing caster in the bottom of the frame leg, lock the
caster by pushing down on the brake lever.
• Twist the stem of the caster into the hole on the bottom of
the leg frame. Applying thread locking adhesive can help
prevent unexpected loosening of the caster.
• Use ¾” wrench to tighten ¾”nut on stem of caster.
• Repeat for remaining casters.
Step 7:
• With someone’s help, turn table upright.
Step 8:
• Align pre-drilled holes in one of the long laminate rails with
the threaded inserts in the side of the top.
• Using a a ¼-20x40mm joint connector bolt, insert the bolt
through the pre-drilled hole in the rail into the threaded
insert of the top. Use a 4mm Allen wrench or a 4mm Hex bit
and and a screw gun to fasten bolt into place.
• After the rst bolt is fastened, proceed attaching the
remaining bolts in the long rail.
• Repeat Step 8 for the remaining three rails.
Step 6
Step 7
Step 8
Tools Required
• Screw gun
• # S2 square bit
• 4mm Hex bit
• 4mm Hex wrench
• ¾”Wrench
• Thread Locking
Adhesive (optional)

3
wibenchmfg.com 507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specications are subject to change. Product
images are for illustrative purposes only and may
dier from the actual product.
Part # Description Qty.
04067960 ¼”-20 x 50mm joint connector bolts 2 per leg frame (4 total)
04009022 ¼”-20 joint connector nuts
(Used to attach cross bar to leg frame) 2 per leg frame (4 total)
04009023 ¼”-20 x 15mm joint connector bolts
(Used to attach leg plates to top) 8 per leg plate (16 total)
0408231 #10 x ¾” Square pan screw
(Used to attach cross bar to top) 3 per side of the cross bar (6 total)
0400993 3” heavy duty locking casters 1 per leg (4 total)
0406526 ¼”-20 x 40mm joint connector bolts
(Used to attach rails to top) 16
Model # Sku # EPIC Frame Leg Descripon
EPC -FX 04067852 EPIC xed frame leg w/3” heavy duty locking casters
EPC -WFX 04067853 EPIC xed frame leg w/3” heavy duty locking casters
EPC -SFX 04067854 EPIC xed frame leg w/3” heavy duty locking casters
04067855 EPIC Frame Adj. Cross Bar 34”- 64”
EPIC Frame Legs and Adj Cross Bar
Standard Frame Color
G4
Smooth Silver
B
Blue
G
Green
Additional Colors
Orange
O
Red
R
Purple
P
Textured Black
09
Tools Required
• Screw gun
• # S2 square bit
• 4mm Hex bit
• 4mm Hex wrench
• ¾”Wrench
• Thread Locking
Adhesive (optional)
EPIC Ingenuity Table
Assembly Instructions
Part Identifier Key