Tot Mate TM2321R User manual

1
#0964-3150
3594.TM2321/TM2325.9/25/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
NOTE: ASSEMBLY INSTRUCTIONS REFERENCE
ILLUSTRATIONS AND PART NUMBERS FOR THE TM2325R.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TM2321R
TM2325R
TM2321R
Mobile Desk
TM2325R
Mobile Desk
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;


'(6&5,37,21
6XSSRUW
(QG5
7RS
(QG/
)URQW
6KHOI
6FUHZ&RQQ+['F1LPP[PP
&VWU8PP7ZLQ:%LQ6HW
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;


'(6&5,37,21
(QG/
(QG5
6XSSRUW
7RS
)URQW
6KHOI
6FUHZ&RQQ+['F1LPP[PP
&VWU8PP7ZLQ:%LQ6HW

TM2321R – TM2325R
STEP-BY-STEP ASSEMBLY
2#0964-3150
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2321/TM2325.9/25/18
ILLUSTRATIONS AND PART NUMBERS ARE FOR TM2325R.
BASIC ASSEMBLY INSTRUCTIONS ARE THE SAME FOR BOTH MODELS.
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (7)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
Caster (8)
(Cstr U 50mm Twin W/B 3/4in Set)
wire cutouts
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
TM2325R
3$5747<,7(0
;;
;;
;;
;;
;;
;;


'(6&5,37,21
(QG/
(QG5
6XSSRUW
7RS
)URQW
6KHOI
6FUHZ&RQQ+['F1LPP[PP
&VWU8PP7ZLQ:%LQ6HW
(Phillips screwdriver required but not included.)

TM2321R – TM2325R
STEP-BY-STEP ASSEMBLY
3
#0964-3150
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2321/TM2325.9/25/18
Position Right End (2) on top of assembly, so
dowels on Front (5), Top (4), Support (3) and
Shelf (6) align with holes on Right End (2). Press
firmly into place.
STEP
3
Secure Right End (2) to Front (5), Top (4),
Support (3) and Shelf (6) with five Confirmat
Bolts (7), using the included Hex Wrench.
STEP
4
Lay Left End (1) flat on floor, with side having the
most holes facing up.
STEP
1
Insert dowels on Front (5), Top (4), Support (3)
and Shelf (6) into holes on Left End (1).Make
sure raw edges are not exposed, and wire cutouts
are oriented correctly, as shown. Make sure four
holes on face of Front (5) align with holes on edge
of Top (4), and four holes on face of Support (3)
align with holes on edge of Shelf (6) (reference
DETAILS A & B). Press all parts firmly into place.
STEP
2
wire cutouts
NOTE: Wire cutouts on
Support (3) are not visible
– reference exploded view
on page 2.
DETAIL B
DETAIL A

TM2321R – TM2325R
STEP-BY-STEP ASSEMBLY
4#0964-3150
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2321/TM2325.9/25/18
Carefully turn assembly over, so Left End (1) is
facing up.
STEP
5
Repeat Step 4 to secure Left End (1) to Front (5),
Top (4), Support (3) and Shelf (6).
STEP
6
Secure Support (3) to Shelf (6) with four
Confirmat Bolts (7) through the aligned holes.
STEP
8
Secure Front (5) to Top (4) with four Confirmat
Bolts (7) through the aligned holes.
STEP
7

TM2321R – TM2325R
STEP-BY-STEP ASSEMBLY
5
#0964-3150
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2321/TM2325.9/25/18
Carefully position the assembly with the bottom
edge facing up.
STEP
9
Mount Casters (8) to Ends (1 & 2) by securing
screws through aligned holes on mounting
brackets and Ends (1 & 2) from outside to inside.
(Phillips screwdriver not included.)
STEP
11
Ensure that all joints, bolts and screws are tight.
STEP
13
This completes the assembly.
Carefully stand unit upright onto casters.
STEP
12
Align mounting bracket holes on Casters (8) with
holes along bottom edge of Ends (1 & 2).
STEP
10
Caster Screw