The Wings Maker Blue Bird EP User manual

Before commencing assembly, please read these instructions thoroughly.
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric power precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Warning ! This model is not a toy.
Wing Span: 78 in /1980mm
Wing Area: 665 sq in / 42.9 sq dm
Flying Weight: 39 oz / 1100g
Fuselage Length: 40 in / 1020mm
Required : speed 550 motor, 3-channel radio
w/ 2 mini servos, 25A speed controller
with brake and 7 cells 1800 mAh battery
Specifications
INSTRUCTION MANUAL
Specifications
GE020
www.thewingsmaker.com

Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer .
I N D E X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.1
P.2
P.3-9
P.9
Apply epoxy glue.
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Drill holes with the specified
diameter(here:3mm)
Pay close attention here!
Pierce the shaded portion
covering film.
Apply instant glue
(C.A. glue, super glue.)
Ensure smooth non-binding
movement while assembling.
Cut off shaded portion.
Must be purchased separately!
Do not overlook this symbol!
3 mm
P.1

C OVERING:
L IGHTEX S GX 0 50 T ransparent B lue
L IGHTEX SGX 100 White
L IGHTEX SGX 310 Red
LIGHTEX SGX 550 Pearl Blue
TOUGHLON STL 451 Checker Blue/White
Parts list
P.2
1. MAIN WING--1 set
WING JOINER Ø6x226mm--1 pc.
2. STABILIZER & ELEVATOR--1 set
3. VERTICAL FIN & RUDDER--1 set
4. PUSHROD Ø1.4x695mm w / Threads(For Elevator)--1 pc.
SCREW PM2x10mm--2 pcs
FUEL TUBE d2xD4x4mm--1 pc.
CLEVIS--1 pc.
HORN--1set
5. PUSHROD Ø1.4x630mm w / Threads(For Rudder)--1 pc.
SCREW PM2x10mm--2 pcs
FUEL TUBE d2xD4x4mm--1 pc.
CLEVIS--1 pc.
HORN--1set
6. SPEED 550 MOTOR--1 set
COWLING--1 pc.
SCREW PWA2x8mm--4 pcs
GEARBOX--1 set
FOLDING PROPELLER SET 1 set
SPINNER Ø45mm 1 set
(12x7)--
--
.
7 SPONGE 10x50x150mm--1 pc.
DOUBLE-SIDED TAPE(30x35mm)--1 pc.
BATTERY TIE--1 pc.
STRAPER--2 pcs
FUEL TUBE d2xD4x4mm--2 pcs
8. PVC PLATE 0.8x25x55mm(Wing Protection)--1 pc.
WASHER d2.5xD8mm--2 pcs
SCREW PM2.5x16mm--2 pcs
9. CANOPY--1 set
10. DECALS--1 set

Main Wing
P.3
1
Stabilizer & Elevator
2
Apply instant type CA glue to both sides of each hinge.
Completed
Wing joiner
Ø6x 226mm
Completed
Bottom View
(Stabilizer)
(Main Wing)
AA'
B B'
B=B'
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
*Also refer to step 10 Wing Setting

P.4
Vertical Fin & Rudder
3
Completed
Apply instant type CA glue to both sides of each hinge.
C=
CC
C
Peel off shaded
portion covering
film.

P.5
7
PM2 x 10mm Screw
2
7
Rudder Pushrod
5
Elevator Pushrod
4
PM2 x 10mm Screw
2
PM2 x 10mm
2mm
PM2 x 10mm
Clevis
Fuel Tube
d2xD4 x 4mm
Horn
2mm
PM2 x 10mm
Fuel Tube
d2 x D4x4mm
Clevis
Horn
2mm
Pushrod
Ø1.4 x 695mm
Pushrod
D1.4 x 630mm
Pushrod
D1.4 x 630mm
210mm
Ø1mm pilot holes for The Wings Maker tri-horn are
pre-driled. Please look for pin-hole marks at under
side of control surfaces.
Ø1mm pilot holes for The Wings Maker tri-horn are pre-driled.
Please look for pin-hole marks at side of control surfaces.

6
45
6
Motor / Cowling Setting
P.6
TO ALLOW FOR
BACKLASH OF
MATCHING GEAR,
PUT A PIECE OF
THIN PAPER
BETWEEN THE
GEARS AND
THEN TIGHTEN
THE M2.6X7mm
SCREWS. REMOVE
THE PAPER
BEFORE FLYING.
3
Ø1.2x41mm
7
3mm Set Screw
2
M3 x 8mm
PM x 1 mm2 6
PM x 1 mm2 6
8
PA2.6 x 8mm
PWA2 x 8mm
Spinner
1mm
PWA2 x 8mm Screw
4
2
M3 x 8mm Socket Head Screw
1
3mm Set Screw
PM x 12mm Screw2.5
2
2
PA2.6 x 8mm Screw
M2.5 Nut
2
d2.5 x D8mm Washer
4
1
PM x 1 mm Screw2 6
2
d3 x D7mm Washer
2
d3 x D7mm Washer
M2.5 Nut
d2.5 x D8mm Washer
PM x 12mm2.5

P.7
C a nopy
9
Completed
Main Wing
8
d2.5 x D8mm Washer
PM2.5 x 16mm Screw
2
2
Radio Equipment
Install and arrange the servo as shown in the diagram.
7
PM2.5 x 16mm
Wing Protection
0.8 x 25 x 61mm
2.5mm
d2.5 x D8mm PM2.5 x 16mm
Peel off shaded portion covering film.
Bottom View
Rudder Servo Rudder Pushrod
Straper
Elevator Pushrod
Elevator Servo
Battery Tie
Fuel Tube
Ø4 x 4mm
Receiver Sponge
25A Speed Controller
Speed 550 Motor Front
Battery
Double-Side Tape
d2.5 x D8mm Washer

P.8
Wing Setting
10
A=A' B=B' C=C'
AA'
BB' C'C

Elevator
Important Safety Precautions
#First time flyer should never fly by himself/herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by geared .
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
speed 550 motor
Warning!
P.9
Control Throws
C.G.
12
The ideal C.G. position is 75mm (2.95 in.) Behind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G.specified, add weight to the fuselage or move the battery
position. Check the C.G. Before flying.
Rudder
30mm
30mm
15mm
15mm
11
75mm
C.G.
2.95in.

P.10
GE0200611
www.thewingsmaker.com
THE WINGS MAKER