The Wings Maker Wingsman II User manual

THE WINGS MAKER
FACTORYPRE-FABRICATED
ALMOST-READY-TO-FLY(ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
Warning ! This model is not a toy.
GA029PO22471205
www.thewingsmaker.com
INSTRUCTION MANUAL
Before commencing assembly, please read these instructions thoroughly.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine(electric) powered precision model. Operating this model without prior preparation may
cause injuries. Remember, safety is the most important thing. Always keep this instruction
manual at hand for quick reference.
Specifications
WingSpan:50in/1270mm
WingArea:484sqin/31.2sqdm
FlyingWeight:3.5lbs/1600g
FuselageLength:44.5in/1130mm
Requires:(Enginepowered)2-stroke0.40engine
4-channelradiow/4standardservos
(Electricpowered)450Wmotorsystem
4-channelradiow/3standardservos
40AESC,4cells14.8V3200mAhLi-Po
battery&charger

INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.11
P.11
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
Apply epoxy glue. Apply instant glue
(C.A.glue, super glue.)
Ensure smooth non-binding
movement while assembling.
Cut off shaded portion.
Must be purchased separately!Apply thread locker
Do not overlook this symbol!
Assemble left and right
sides the same way.
Pierce the shaded portion
covering film.
Peel off shaded portion
covering film.
Drill holes with the specified
diameter (here: 3mm)
Pay close attention here!
3mm
P.1

Parts List
P.2
COVERING:--
LIGHTEX SGX 201 BLACK
TOUGHLON STL100 WHITE
TOUGHLON STL 311 FERRARI RED
TOUGHLON STL 330 CADMINU YELLOW
TOUGHLON STL 540 PEARL GREEN
TOUGHLON STL GA029 RED/WHITE
TOOGHLON STL GA029 RED/YELLOW
TOUGHLON STL GA029 GREEN/WHITE
1. MAIN WING -- 1 pair
2. WING JOINER 6x18x180mm -- 1 pc.
3. FUELTUBE d2xD4x4mm -- 4 pcs
CLEVIS -- 2 pcs
STRAPER -- 2 pcs
RING Ø2.3mm -- 2 pcs
PUSHROD Ø1.4x110mm w/ Threads ( For Aileron) -- 2 pcs
PLYWOOD 2x8x22mm (ForAileron Servo) -- 1 pc.
PLYWOOD 4x8x22mm (ForAileron Servo) -- 1 pc.
4. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
5. VERTIACL FIN & RUDDER -- 1 set
SCREW PM3x60mm -- 2 pcs
WASHER d3xD7mm -- 2 pcs
6. MAIN LANDING GEAR -- 1 pair
COLLAR Ø3.1mm w/ set screw -- 4 sets
WHEEL Ø55mm -- 2 pcs
SCREW PA3x10mm -- 4 pcs
MOUNTING PLATE 12x20mm -- 2 pcs
7. TAIL LANDING GEAR -- 1 set
COLLAR Ø2.1mm w/ set screw -- 1 set
WHEEL Ø23mm -- 1 pc.
STEERING BRACKET -- 1 pc.
SCREW PA3x8mm -- 2 pcs
SCREW PM2x10mm -- 1 pc.
M2 NUT -- 1 pc.
8. SCREW PB2x10mm -- 2 pcs
FUEL TUBE d2xD4x4mm -- 1 pc.
CLEVIS -- 1 pc.
HORN -- 1 set
PUSHROD Ø1.4x655mm w/ Threads (For Elevator) -- 1 pc.
9. SCREW PB2x10mm -- 2 pcs
FUEL TUBE d2xD4x4mm -- 1 pc.
CLEVIS -- 1 pc.
HORN -- 1 set
PUSHROD Ø1.4x655mm w/ Threads (For Rudder) -- 1 pc.
10.SPINNER Ø52mm -- 1 pc.
11. STRAPER -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
SPONGE 10x80x200mm -- 2 pcs
12. SCREW PM2x10mm -- 2 pcs
WASHER d2xD5mm -- 2 pcs
M2 NYLON INSERT LOCK NUT -- 2 pcs
MOUNTING PLATE (PL4114015) -- 2 pcs
PLYWOOD 2x67.5x94.3mm -- 1 pc.
PLYWOOD 2x67.4x133mm -- 1 pc.
13. SCREW HM3x25mm -- 2 pcs
WASHER d3xD7mm -- 2 pcs
PLASTIC PLATE 1x15x80mm -- 1 pc.
14. CANOPY -- 1 pc.
SCREW PWA2.3x8mm -- 4 pcs
15. DECALS: GA029 DEC -- 1 set

Main Wing
Main Wing
Aileron Servo
Apply instant type CA glue to both sides of each hinge.
Please dry fit wing joiner into left and right wing to make sure they fit with the proper
dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to both sides of
all surfaces in contact. Use a stick to apply the glue to inner side of wing joiner
sleeve, and apply the glue to wing joiner before putting them together. Wing joiner
not glued properly will lead to wing failure and plane crash.
Wing Joiner
Ring
Plywood
4x8x22mm Plywood
2x8x22mm
Straper
Clevis
Fuel Tube
d2xD4x4mm
1.5mm
Completed
Completed
P.3
2
3
1
TWM PL8210010
CLEVIS WRENCH

Vertical Fin & Rudder
Stabilizer & Elevator
Completed
Apply instant type CA
glue to both sides of
each hinge.
Apply instant type CA glue
to both sides of each hinge.
Temporary install the main wing,
adjust leveling of the stabilizer
to make is as parallel to the main
wing as possible.
(Stabilizer)
(Main Wing)
B
B=B
B
A=A
A A
C=C
CC
PM3x60mmScrew
PM3x60mm
2
d3xD7mmWasher
d3xD7mm
Washer
2
Main Landing Gear
PA3x10mmScrew
PA3x10mm
MountingPlate
4
3.1mmCollar 4
Bottom View
1.5mm
6
3.1mm Collar
3mm Set Screw
Completed
P.4
5
4

Tail Landing Gear
PM2x12mmScrew 1
M2Nut 1
PA3x12mmScrew
PA3x12mm
2
2.1mmCollar 1
1.5mm
Elevator Pushrod
PB2x10mm Screw
2
Ø1mm pilot holes for The Wings Maker horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
≈175mm
≈40mm
8
Clevis
Horn
PB2x10mm Fuel Tube
d2xD4x4mm
Pushrod
Ø1.4x655mm
Rudder Pushrod
Clevis
Fuel Tube
d2xD4x4mm PB2x10mm
Pushrod
Ø1.4x655mm Horn
Ø1mm pilot holes for The Wings Maker horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
≈175mm
≈40mm
9
PB2x10mm Screw
2
P.5
7
PM2x8mm
M2Nut
SteeringBracket
Ø2.1mmCollar
3mmSetScrew
TWM PL8210010
CLEVIS WRENCH
TWM PL8210010
CLEVIS WRENCH

UP
Engine
d3xD7mm
Washer
EngineMount
PL5111030
M3x20mm
Blind nuts are off-centered to keep the
spinner at the fuselge axis.
Apply thread locker to screws.
Installed Engine Position
3.2mm
Fuel Tank
320cc
Fuel Tank
320cc
Install Balsa 8x8x76mm
(For Fuel Tank Position Fixing)
M3x25mm
PlasticTube
d2xD3x180mm
Pushwire
Ø1.2x370mm
d3xD7mm
Washer
d3xD7mm
Washer
M3Nut
Spinner
Ø52mm
105mm
3.94in
Bottom View
Bottom View
Throttle Pushwire
Ø1.4x655mm
Throttle Servo
Plastic Tube
d2xD3x240mm
This step is for engine powered. Please
follow step 10B if your model is electric
powered.
To complete your Wingman ll (nitro powered),
you need to purchase The Wings Maker
GA029GPTS.
Optional parts for nitro powered
Wingman lI, GA029GPTS.
GA029GPTS
P.6
10A

Electric
d3xD7mm
Washer
M2.5x12mm
M3x8mm
Completed
10B
GA029EPTS
If you want to use electric powered, please follw this step.
To Complete your
Wingman lI (electric
powered), you need
to purchase The
Wings Maker
GA029EPTS.
d3xD7mm
Washer
M3x12mm
Battery Tie
Spinner
Ø52mm
M6NUT
40A Brushless ESC
Double-Sided
Tape
Bottom View
P.7

Install and arrange the servos as shown in the diagram.
P.8
Radio Equipment
11
Front
A
B
Fuel Tube
d2xD4x4mm
Fuel Tube
d2xD4x4mm
Front
Throttle Pushwire
Ø1.4x655mm
w/ Plastic Tube
d2xD3x240mm
Receiver
Rudder Servo
Rudder Servo
Throttle Servo
Elevator Servo
Elevator Servo
Straper
Straper
Sponge
Sponge
Battery
Receiver
Battery
Bottom View
Bottom View
Engine Powered
Electric Powered
Fuselage Cover
12
PM2x10mmScrew
PM2x10mm PM2x10mm
d2xD5mmWasher
d2xD5mm
Washer d2xD5mm Washer
2
2
2
2mm
Plywood2x67.5x94.3mm
Mounting Plate Mounting Plate
M2NylonInsertLockNut
M2NylonInsertLockNut
Bottom View
Plywood2x67.4x133mm
2mm
M2NylonInsertLockNut
Charge Receptacles
KP0041300

P.9
Main Wing
13
HM3x25mmScrew
HM3x25mm
PlasticPlate1x15x80mm
d3xD7mmWasher
d3xD7mm
Washer
2
2
Bottom View
PM3x25mm
d3xD7mm
Washer
14Canopy
PWA2.3x8mmScrew
4
1mm
3mm

P.10
Wing Setting
15
Adjust the wing and fuselage configuration as shown in the diagrams.
A=A' B=B' C=C' D=D'
B B’
A A’
D
C C’
D’
Control Throws
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
Rudder 20mm
20mm
15mm
15mm
Elevator
6mm
6mm
Ailerons
16

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by 2C 0.40 engine or 450W motor system.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue
and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
Wingman ll
C.G.
The ideal C.G. position is 76mm (3 in.) behind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G. specified, add weight to the fuselage or move the battery
position. Check the C.G. before flying.
76mm
76mm
C.G.
3 in
3 in
P.11
17
Warning!
Important Safety Precautions

LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn. Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.

Optional Parts
Clevis Wrench
Code No. Size Package
PL8210010 1 set
Special tool for clevis installation.
Suitable for standard and small
(EP) clevis.
Small Clevis Large Clevis
Field Stand
Code No. Size Package
MS9111430 600 x 240 x 310mm 1 pc
( ACCESSORIES)
Fuel Filler
Code No. Size Package
PL8110030 15 x 22 x 49mm 1 x 1 pc
Charge Receptacles
Code No. Size Package
KP0041300
Speed : 0.17 sec / 60° @4.8V
0.14 sec / 60° @6.0V
Torque : 3.2kg.cm / 44.8 oz - in @4.8V
4.1kg.cm / 57.4 oz - in @6.0V
Size : 40.6 x 20 x 37mm /
1.60 x 0.79 x 1.46 in
Weight : 39.4 g / 1.39 oz
Code No SV4031
Standard Servo
13860
770
KM0374810
37/ 48 Deluxe
450
8.5-18
30
38 34
37.2
48.5
172 5
21 (Front) and M2.5 (Back)
25mm (Front) and 15.5mm (Back)
40A Brushless ESC
6 ~ 21V
40 55
33
3
KC2040A02 55x28x12mm

THE WINGS MAKER
www. thewingsmaker.com