The Wings Maker Handyman EP User manual

It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Warning ! This model is not a toy.
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
www thewingsmaker com. .
SpecificationsSpecifications
Before commencing assembly please read these instructions thoroughly, .
INSTRUCTION MANUAL
Wing Span: 36.5 in / 930 mm
Wing Area: 346 sq in / 22.3 sq dm
Flying Weight: 19-23 oz / 540-650 g
Fuselage Length: 41.5 in / 1055 mm
Requires: 4-channel radio w/ 4 micro servos. Outrunner
Motor KM0283010 w/ Propeller Adaptor HW2340100
20A Brushless ESC, 2 cells 7.4V 15C 1300 mAh
(indoor flying) to 3 cells 11.1V 15C 1800 mAh
(outdoor flying) Li-Po battery & charger.
GE039PO22591118
Handyman EP

INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.9
P.9
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
P.1
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
Handyman EP

P.2
Parts List
1.MAIN WING -- 1 pair
SCREW PB2x22mm -- 4 pcs
STRAPER PL4112106 -- 2 pcs
CLEVIS PL4112105 -- 2 pcs
HORN PL4113102 -- 2 sets
FUEL TUBE d2xD4x4mm -- 4 pcs
PUSHROD Ø1.4x60mm w/ Threads (ForAileron) -- 2 pcs
FIBRE TAPE 17x420mm -- 2 pcs
2.FUSELAGE -- 1 set
STABILIZER & ELEVATOR -- 1 set
FIBRE TAPE 17x300mm -- 1 pc.
3.VERTICAL FIN & RUDDER -- 1 set
FIBRE TAPE 17x200mm -- 1 pc.
4.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x10mm -- 2 pcs
5.MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
SCREW PA2x8mm -- 2 pcs
PLYWOOD 26x40x2.5mm (For Main Landing Gear) -- 1 pc.
6.SCREW PB2x18mm -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113102 -- 1 set
PUSHROD Ø1.4x50mm w/ Threads (For Elevator) -- 1 pc.
7.SCREW PB2x18mm -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113102 -- 1 set
PUSHROD Ø1.4x125mm w/ Threads (For Rudder) -- 1 pc.
8.SCREW PM3x6mm -- 4 pcs
SCREW PM2x12mm -- 2 pcs
SCREW PA2.6x8mm -- 2 pcs
WASHER d3xD7mm -- 4 pcs
SPINNER Ø45mm -- 1 pc.
FOLDING PROPELLER SET PL6314020 -- 1 set
9.WING TUBE Ø6x360mm -- 1 pc.
RUBBER BAND 1x30mm -- 2 pcs
10.BATTERY COVER -- 1 pc.
BATTERY TIE 200mm-- 1 pc.
SPONGE 10x50x150mm (For Radio Equipment) -- 1 pc.
DOUBLE-SIDED TAPE 30x35mm (For Brushless ESC) -- 1 pc.
11.DECALS: GE039 DEC -- 1 set

P.3
Bottom View Bottom View
Bottom View
Please do not overtighten PB2x22mm screw. Once the screw brings the horn
and backplate in contact with the foam, add 1/2 turn will do. Overtightening
will damage the foam.
√×
Ø1mm pilot holes for The Wings
Maker horn are pre-drilled. Please
look for pin-hole marks at under
side of control surfaces.
Aileron Servo
1
PB2x22mm Screw
4
Fibre Tape
17x420mm
Servo(For Aileron)
Aileron Servo Lead
Straper
PB2x22mm Clevis
Fuel Tube
Pushrod
Ø1.4x60mm
d2xD4x4mm
Horn
Fibre Tape
Bottom
TWM PL8210010
CLEVIS WRENCH

P.4
0
Vertical Fin & Rudder
3
Completed
0
Tail Landing Gear
4
Bottom View
PA2x10mm Screw
2
Fibre Tape
17x420mm
Fibre Tape
Plastic
Collar
Wheel Ø23mm
PA2x10mm
1.2mm
Bottom View
Stabilizer & Elevator
2
Fibre Tape
17x300mm
FibreTape
Bottom
Joining surfaces should
be clean and dry. Slightly
roughen surfaces with
sandpaper for best results.
Joining surfaces should be clean and dry. Slightly roughen
surfaces with sandpaper for best results.

Main Landing Gear
Elevator Pushrod
5
6
Bottom View
Bottom View
P.5
M3x3mm Set Screw
2.6mmCollar
Bottom View
Bottom View Bottom View
Wheel Ø40mm
PA2x8mm Screw
2
PA2x8mm
Plywood
Landing Gear
26x40x2.5mm
2.6mm Collar
2
PB2x18 mm Screw
2
Ø1mm pilot holes for The Wings Maker horn are
pre-drilled. Please look for pin-hole marks at under
side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
Please do not overtighten PB2x18mm screw. Once the screw brings the horn and backplate in
contact with the foam, add 1/2 turn will do. Overtightening will damage the foam.
√×
Fuel Tube
d2xD4x4mm
Horn
Pushrod
Ø1.4x50mm
Straper
Clevis
PB2x18mm
Elevator Servo

Outrunner Motor 28/ 30
KM0283010
PropellerAdaptor
(d3xD5) HW2340100
Rudder Pushrod
Outrunner Motor / Spinner
7
8
P.6
PB2x18 mm Screw
2
Ø1mm pilot holes for The Wings Maker horn are pre-drilled.
Please look for pin-hole marks at under side of control
surfaces.
PA2.6x8mm Screw
2
PM3x6mm Screw
4
PM2x12mm Screw
2
d3xD7mm Washer
4
Don’t over-tighten the PM2 screws, let the propeller
blades align themselves when spinning.
3
PM2x12mm
PM2x12mm
Make sure rotating motor casing is not in
contact with wirings or anything.
Optional Parts
TWM PL8210010
CLEVIS WRENCH
Please do not overtighten PB2x18mm screw. Once the screw brings the horn and backplate in
contact with the foam, add 1/2 turn will do. Overtightening will damage the foam.
√ ×
2
d3xD7mm Washer
PM3x6mm
Don't over-tighten the PM3 screws, too much
stress on the screws could split the firewall.
1
Brushless ESC
EZ Connector
Solder Solder
TWM
KP0011310
ESC Ducted Fan
Straper
Fuel Tube
d2xD4x4mm
PB2x18mm
Clevis
Horn
Pushrod
Ø1.4x125mm
Rudder Servo
4 5
M5 Nut
Ø45mm
PA2.6x8mm
TWM HW3111400
PROPELLER ADAPTOR WRENCH Completed

P.7
Main Wing
9
Rubber Band
Wing Tube
Aileron Servo Lead
Ø6x360mm
Radio Equipment
10
Battery
Install and arrange the equipment as shown in the picture.
Outrunner Motor
Battery Tie Sponge
Receiver
Front
Brushless
ESC
Double Sided Tape
Completed
Fuselage Bottom
Battery Cover
Completed

P.8
Bottom View
Top View
Control Throws
12
Elevator
Rudder
Ailerons
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
40mm
40mm
50mm
50mm
60mm
60mm
Decals
11

P.9
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by KM0283010 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your
hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
Warning!
Handyman EP
C.G.
13
The ideal C.G. position is 110mm (4.33in.) behind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G. specified, add weight to the fuselage or move the battery
position. Check the C.G. before flying.
110mm
4.33in
C.G.

Large Clevis
•
Small Clevis
•
Pl8210010

THE WINGS MAKER
www.thewingsmaker.com