The Wings Maker ARF Ultimate EP User manual

It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Warning ! This model is not a toy.
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
www thewingsmaker com. .
SpecificationsSpecifications
Before commencing assembly please read these instructions thoroughly, .
INSTRUCTION MANUAL
Wing Span: 32.5 in / 825 mm
Wing Area: 357 sq in / 23 sq dm
Flying Weight: 24 oz / 680 g
Fuselage Length: 34 in / 870 mm
Requires: 4-channel radio w/ 3 micro servos. Outrunner
Motor KM0283011 w/ Propeller Adaptor HW2340100
20A Brushless ESC,3 cells 11.1V 1300 mAh Li-Po
battery & charger.
(GM052)
GM052XMPO28951303

INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.10
P.10
P.1
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer. For pre-assembled kits, please check proper
functions of all servos on the ground before flying. Servo gears could be damaged when
control surfaces are hit during transportation of models. The manufacturer will replace any
servos due to manufacturer`s defect, but will not cover plane crashes due to damaged
servos not detected before flying.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
GM052XMPO28951303

P.2
Parts List
1.MAIN WING -- 1 set
PLASTIC BRACKET -- 2 pcs
FIBRE TAPE 17x380mm -- 4 pcs
2.BALL JOINT CONTROLARM PL4203100 -- 2 sets
SCREW PM2.5x12mm -- 2 pcs
WASHER d2.5xD8mm -- 2 pcs
PUSHROD Ø1.4x92mm w/ Threads (ForAileron) -- 2 pcs
STRAPER PL4112106 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
3.FUSELAGE -- 1 set
STABILIZER & ELEVATOR -- 1 set
FIBRE TAPE 17x240mm -- 1 pc.
4.VERTICAL FIN & RUDDER -- 1 set
FIBRE TAPE 17x215mm -- 1 pc.
PLASTIC BRACKET -- 2 pcs
5.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x8mm -- 2 pcs
TAIL WHEEL Ø23mm PL3510230 -- 1 pc.
PLASTIC BRACKET -- 2 pcs
6.MAIN LANDING GEAR -- 1 set
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
PLYWOOD COLLAR Ø8x2mm -- 2 pcs
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
SCREW PA2.6x8mm -- 1 pc.
PLYWOOD 26x20.4x2.5mm (For Main Landing Gear) -- 1 pc.
MAIN LANDING GEAR COVER -- 1 pair
WHEEL PANT -- 1 pair
MOUNTING PLATE PL4114020 -- 2 pcs
SCREW PWA2x6mm -- 4 pcs
7.CLEVIS PL4112105 -- 1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x73mm w/ Threads (For Elevator) -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
8.CLEVIS PL4112105 -- 1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x133mm w/ Threads (For Rudder) -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
9.SOCKET HEAD SCREW M3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
SPINNER Ø36mm -- 1 set
PROPELLER PL6314050 -- 1 set
10.CANOPY -- 1 pc.
11.SIDE CABANE -- 2 pcs
CENTER CABANE -- 1 pc.
12.PUSHROD Ø1.4x125mm w/ Threads (For Elevator) -- 2 pcs
CLEVIS PL4112105 -- 4 pcs
HORN PL4113103 -- 4 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
13.BATTERY COVER -- 1 pc.
BATTERY TIE 160mm-- 1 pc.
BATTERY MAT 2x50x150mm -- 2 pcs
DOUBLE-SIDED TAPE 30x35mm (For Brushless ESC) -- 1 pc.
14.DECALS: GM052 DEC -- 1 set
GM052XMPO28951303

P.3
Main Wing
1
Aileron Servo Lower Wing
2
Fibre Tape Bottom
Bottom View
Bottom View
PM2.5x12mm
Washer
d2.5xD8mm
Straper
Ball Joint Control Arm
Pushrod
Ø1.4x92mm
Bottom View
Upper
Lower
PM2 . 5 x 12mm
d2.5xD8mm Washer
Screw
2
2
Fibre Tape 17x380 mm
Fibre Tape 17x380 mm
Fuel Tube
d2xD4x4mm
TWM PL8210010
CLEVIS WRENCH
Plastic Bracket
GM052XMPO28951303

P.4
0
Vertical Fin & Rudder
4
Completed
0
Tail Landing Gear
5
Bottom View
Fibre Tape
17x215mm
Fibre Tape
Bottom View
Stabilizer & Elevator
3
Fibre Tape 17x240 mm
FibreTape
Bottom
Joining surfaces should
be clean and dry. Slightly
roughen surfaces with
sandpaper for best results.
Joining surfaces should be clean and dry. Slightly roughen
surfaces with sandpaper for best results.
PA2x8mm Screw
2
Plastic
Collar
Wheel Ø23mm
PA2x8mm
1.2mm
Plastic Bracket
Plastic Bracket
GM052XMPO28951303