THE WORLD MODELS Super Sports Senior- 90 User manual

Super Sports Senior- 90
0.91 cubic inch displacement 4- stroke (glow)
Radio required: 4 channel 5 servos
- radio w/
Specifications
Wing Span
Wing Area
Flying Length
Fuselage Length
81 in / 2050mm
1020 sq in / 65.8 sq dm
9 lbs / 4100 g
61 in / 1560mm
Warning ! This model is not a toy.
It is designed for precision model. Please seek advice if one familiar this kind of
engine powered precision model. Operating this model without prior preparation
may cause injuries. Remember, safety is the most important thing. Always keep
this instruction manual at hand for quick reference.
* Specifications are subject to change without notice. *
INSTRUCTION MANUAL
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA

Super Sports Senior - 90
P. 1
I N D E X
P. 3 -10
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
3mm
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 10
BEFORE YOU BEGIN
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
1
2
3

P. 2
Parts List
1. MAIN WING -- 1 pair
2. SCREW PM2 X 20mm -- 2 pcs
SCREW PM2 X 25mm -- 4 pcs
PUSHER ROD Ø1.8 x 106mm w/ Threads (For Aileron) -- 2 pcs
TRI-HORN M3 X 14mm (L) -- 2 sets
CLEVIS -- 2 pcs
STRAPER -- 2 pcs
FUEL TUBE Ø6 X 5mm -- 4 pcs
3. MAIN LANDING GEAR -- 1 pair
MAIN LANDING GEAR COVER -- 1 set
MOUNTING PLATE 12 X 20mm -- 4 pcs
SCREW PA3 X 14mm -- 8 pcs
SCREW PM2 X 8mm -- 8 pcs
WASHER d2 X D5mm -- 16 pcs
M2 NUT -- 8 pcs
4. SCREW PA3 X 12mm -- 4 pcs
COLLAR Ø5.1mm w/ Set screw -- 4 sets
MAIN WHEEL Ø90mm -- 2 pcs
WHEEL PANTS -- 1 pair
MOUNTING PLATE 12 X 20mm -- 2pcs
5. WING TUBER Ø18 X 701mm -- 1 pc.
6. STABILIZER & ELEVATOR -- 1 set
SCREW PM3 X 25mm -- 1 pc.
WASHER d3 X D7mm -- 1 pc.
FUSELAGE -- 1 pc.
7. VERTICAL FIN & RUDDER -- 1 set
8. TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
SCREW PA3 X 12mm -- 2 pcs
COLLAR Ø2.1mm w/ Set screw -- 1 set
SCREW PM2 X 14mm -- 1 pc.
WASHER d2 X D5mm -- 2 pcs
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1 pc.
9. FUEL TANK 450CC -- 1 set
BALSA 8 x 10 x 116mm (For fixing fuel tank) -- 1 pc.
10. ENGINE MOUNT (PL5911120) -- 1 set
SOCKET HEAD SCREW M6 X 30mm -- 4 pcs
WASHER d6 X D15mm -- 4 pcs
11. THROTTLE PUSHWIRE Ø1.2 x 340mm
w/Plastic tube d2 x D3 x 185mm -- 1 set
ALUMINUM PLATE (For Engine Mount) – 1pc.
ANTI - VIBRATION MOUNT -- 1 set
INCLUDE: SCREW M4 X 35mm -- 4 pcs
SCREW KM3 X 20mm -- 8 pcs
WASHER d4 X D12mm -- 8 pcs
M3 NYLON INSERT LOCK NUT -- 8 pcs
M4 NYLON INSERT LOCK NUT -- 4 pcs
12. COWLING -- 1 set
TRANSPARENT DUMMY COWLING -- 1 set
PWA2.6 X 12mm -- 5 pcs
SILICON GROMMET d1.5 X D6.5mm -- 5 pcs
SPINNER Ø70mm -- 1 set
13. WIRE Ø1 x 900mm (For Rudder) -- 2 pcs
COPPER TUBE d2.5 X D3.2 X 8mm -- 2 pcs
RIGGING COUPLER Ø1.8 X 27mm w/ Threads (For Rudder) -- 2 pcs
SCREW PM2 X 16mm -- 3 pcs
M2 NUT -- 3 pcs
TRI-HORN M3 X 14mm (L) (w/ o - Base For Rudder) -- 2 sets
FUEL TUBE Ø6 X 5mm -- 2 pcs
CLEVIS -- 2 pcs
14. PUSHROD Ø1.8 x 660mm w/ Threads (For Elevator) -- 2 pcs
TRI-HORN M3 X 4mm (L) -- 2 sets
SCREW PM2 X 16mm -- 6 pcs
CLEVIS -- 2 pcs
FUEL TUBE Ø6 X 5mm -- 2 pcs
15. LINKAGE CONNECTOR Ø2.1mm -- 1 set
16. SPONGE 60 X 70 X 115mm -- 1 pc.
RIGGING Z BEND Ø1.8 x 27mm (For Rudder) -- 2 pcs
PUSHROD Ø1.8 x 170mm (For Elevator) -- 1 pc.
COPPER TUBE d2.5 X d3.2 X 8mm -- 2 pcs
STRAPER -- 1 pc.
FUEL TUBE Ø6 X 5mm -- 1 pc.
PLYWOOD 120 X 35 X 6mm (For Throttle Servo) -- 1 pc.
BALSA 6 x 6 x 35 (For Throttle Servo Stand) -- 2 pcs
PUSHROD CONNECTOR 8 X 9 X 20mm -- 1 set
17. CANOPY -- 1 set
SCREW PWA2.3 X 8mm -- 8 pcs
SILICON GROMMET d1.5 X 6.5mm -- 8 pcs
PILOT PL001085A/B -- 1 pc.
18. SCREW PM4 X 35mm -- 2 pcs
WASHER d4 X D15mm --2 pcs
PLYWOOD 2 x 30 x 120mm (Wing Protection) -- 1 pc.
19. DECALS -- 1 set
COVERING:
RED COLOR SCHEME:
TOUGHLON STL 312 BRIGHT RED
TOUGHLON STL 320 ORANGE
TOUGHLON STL 330 CADMIUM YELLOW
TOUGHLON STL 351 DARK BLUE
TOUGHLON STL 100 WHITE
PURPLE COLOR SCHEME:
TOUGHLON STL 351 DARK BLUE
TOUGHLON STL 360 VIOLET
TOUGHLON STL 361 PURPLE
TOUGHLON STL 241 TURQUOISE
TOUGHLON STL 100 WHITE

Pre-glued
PM2 x 20mm Screw
PM2 x 25mm Screw
2
4
PA3 x 14mm Screw
PM2 x 8mm Screw
d2 x 5mm Washer
M2 Nut
8
8
16
8
PA3 x 14mm
PM2 x 8mm
Straper
Pusher Rod
1.8 x 106mm
PM2 x 20mm
PM2 x 25mm
Fuel Tube
6 x 5mm
Tri-horn
M3 x 14mm
d x D5 Washer2 mm
M2 NUT
Plate
P. 3
Main Wing
1
Aileron Servo
2
Main Landing Gear
3
Bottom View
Bottom View
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.

P. 4
PA 3 x 12mm Screw
3mm Set Screw
5.1mm Collar
4
4
4
PA 3 x 12mm
3mm Set Screw
5.1mm Collar
Wheel 90mm
Completed
Wing Tuber
Ø18 x 701mm
Lead to aileron Servo.
Peel off shaded portion
covering film for lead to
another aileron servo.
Peel off shaded portion
covering film
PM3 x 25mm
d3 x D7mm
d3 x D7mm Washer
PM3 x 25mm Screw
1
1
Apply thread locker to screws.
Bottom View
Pre-glued
Main Landing Gear
4
Main Wing
5
Stabilizer / Elevator
6

P. 5
A = A'
A A'
d2 x D5mm Washer
Washer 2mm
3mm Set Screw
PA 3 x 12mm Screw
2.1mm Wheel Collar
3mm Set Screw
PM2 x 14mm Screw
d2 x D5mm Washer
M2 Nut
2
1
1
1
2
1
PM2 x 14mm Screw
PM2 x 14mm
PA3 x 12mm
Install Balsa 8 x 10 x 116mm
(For fixing fuel tank)
Fuel Tank 450cc
Fuel Tank
450cc
Vertical Fin / Rudder
7
Tail Landing Gear
8
Fuel Tank
9
2mm
Pre-glued

P. 6
Engine Mount
Pl5911120
Apply thread locker to screws.
Illustration is for inverted mounting.
You can mount the engine upright
or sideways simply by rotation the
engine mount. Thrust angles will
not be affected.
Make sure the rounded edges
are facing the shock absorbing
SILICON PAD.
KM3 x 20mm
3mm Install Engine position
142mm
5.6in.
Spinner
70mm
M4 Nylon
Insert Lock Nut
d4 x D12mm
Washer
M4x35mm
SOCKET HEAD SCREW
Throttle Push wire
1.2 x 340mm
Plastic Tube
d2 x D3 x 185mm
d6 x D15mm
M6 x 30mm
Blind nuts are off-centered to keep
the spinner at the fuselage axis.
M6 x 30mm Socket Head Screw
d6 x D15mm Washer
4
4
Engine Mount
10
Engine
11
M4 Nylon Insert Lock Nut
4
8
4
8
d4 x D12mm Washer
KM3x20mm Screw
M3 Nylon Insert Lock Nut
8
M4x35mm SOCKET HEAD SCREW
d4 x D12mm
Washer

P. 7
PWA2.6 x 12mm
Silicon Grommet
d1.5 x 6.5mm
5
5
PWA2.6 x 12mm Screw
d1.5 x D6.5mm Silicon Grommet
Spinner
Cowling
12
PM2 x 16mm Screw
M2 Nut
3
3
Tri-horn
PM2 x 16mm
M2 Nut
Rudder Pullwire
13
Wire Ø1 X 900mm
Elevator Pushrod
14
PM2 X 16mm Screw
6
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Pushrod Ø1.8 X 660mm
w/Threads
PM2 X 16mm
Clevis
Fuel Tube
235mm
135mm
First insert the grommet to the cowling then apply screw.

P. 8
Please refer to attached sheet for linkage connector installation.
LINKAGE CONNECTOR
Linkage Connector
3 x 3mm Set Screw
2mm Nut
2mm Washer
1
1
1
2
Throttle Rod
2mm
2mm
Included with the Radio Set.
Throttle Servo.
3mm
Servo Set
15
Bottom View
Install and arrange the servo as shown in the diagram.
Radio Equipment
16
Elevator Servo
Pushrod 1.8 X 170mm
Pushrod Connector
8 X 9 X 20mm
Balsa 6 x 6 x 35mm
Balsa 6 x 6 x 35mm
Throttle
Servo
Plywood
35 x 6 x 120mm
Spong 60 X 70 X 115mm Rudder Servo
Rigging Z Bend
Ø1.8 x 27mm
Copper Tube
Front
Fuel Tube
Wire Ø1 X 900mm
Straper
Press down the center
1/3 portion
Copper Tube
Elevator Servo
Bottom View
KM 2x8mm
M2 Nut
Elevator Pushrod
Ø1.8x170mm

Pilot Silicon Grommet
d1.5 x 6.5mm
PWA2.3 x 8mm
P. 9
Bottom View
PM4 x 35mm
d4 x D15mm
PM4 x 35mm Screw
d4 x D15 Washer
2
2
A A'
A = A'
B = B'
C = C'
B B'
C C'
Adjust the wing and fuselage configuration
as in the diagrams.
0
2.5
1.5
Main Wing
18
Wing Setting
19
Canopy
17
8
8
d1.5 x D6.5mm Silicon Grommet
PWA2.3 x 8mm Screw
First insert the grommet to the canopy then apply screw.
4mm

P. 10
108mm
The ideal C.G. Position is 108mm (4.25 in) behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
Super Sports Senior - 90 is specially designed to be powered by 0.91 4 stroke
glow engine, using a more powerful engine does not mean better performance. In fact,
over powered engine may cause severe damage and injuries.
Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
Check and re-tighten up all factory assembled screws, use thread locker if applicable.
Important Safety Precautions
A119R0610
C.G
21
20mm
Elevator
Rudder
Aileron
20mm
44mm
44mm
9mm
9mm
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
Control Throws
20

A119R0610
The World Models
Manufacturing Co., LTD.
www.theworld model s.com
Warbirds
Scale
Sports
Trainer
DuctedFan Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)