THE WORLD MODELS Hall Cherokee II User manual

Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
Wing Span
Wing Area
Flying Weight
Fuselage Length
130.7 in / 3320 mm
1190 sq in / 76.8 sq dm
8.33 Ib / 3780 g
64.5 in / 1637 mm
Specifications
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
Requires: 5-channel radio w/ 7 Standard servos.
(G336)
1/4 SCALE HALL CHEROKEE II1/4 SCALE HALL CHEROKEE II
G336PO29441308

INDEX
BEFORE YOU BEGIN
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.9
P.9
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CAor Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
Read through the manual before you begin, so you will have an overall idea of what to do.
1
2
3
P.1
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Pay close attention here!
Apply epoxy glue.
Must be purchased separately !
Drill holes with the specified
diameter (here: 3mm). Pierce the shaded portion
covering film.
3mm
Do not overlook this symbol !
Warning!
Apply thread locker
1/4 SCALE HALL CHEROKEE II1/4 SCALE HALL CHEROKEE II
G336PO29441308

Parts List
P.2
COVERING:--
LIGHTEX SGX 311 FERRARI RED
LIGHTEX SGX 201 BLACK
TOUGHLON STL 100 WHITE
Wing Bag: --
Wing Bag -- 1 pc.
Plastic Stand -- 3 pcs
1. MAIN WING -- 1 pair
2. PUSHROD Ø1.8x60mm w/ Threads (For Aileron) -- 2 pcs
PUSHROD Ø1.8x50mm (For Spoiler) -- 2 pcs
SCREW PB2x22mm -- 4 pcs
SCREW PWA2x8mm -- 16 pcs
HORN PL4113101 -- 2 sets
STRAPER PL4112102 -- 4 pcs
CLEVIS PL4112103 -- 2 pcs
FUEL TUBE D6x5mm -- 6 pcs
SERVO MOUNTING PANEL 58x64x2mm -- 2 pairs
BALSA 21x18x8mm (For Servo Mounting Panel) -- 8 pcs
LINKAGE CONNECTOR Ø2.1xD6mm w/ set screw -- 2 set
WIRE Ø3x45mm -- 2 pcs
ALUMINIUM PLATE -- 2 pcs
3. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
SCREW PM3x40mm -- 2 pcs
WASHER d3.2xD12mm -- 2 pcs
4. VERTICAL FIN & RUDDER -- 1 set
5. PUSHROD Ø1.8x165mm w/ Threads (For Rudder)) -- 1 pc.
SCREW PB2x30mm -- 2 pcs
HORN PL4113101 -- 1 set
CLEVIS PL4112103 -- 1 pc.
FUEL TUBE D6x5mm -- 2 pcs
STRAPER PL4112102 -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
SERVO MOUNTING PANEL 58x64x2mm -- 1 pc.
BALSA 21x18x8mm (For Servo Mounting Panel) -- 2 pcs
6. PUSHROD Ø1.8x145mm w/ Threads (For Elevator) -- 1 pc.
SCREW PB2x25mm -- 2 pcs
HORN PL4113101 -- 1 set
CLEVIS PL4112103 -- 1 pc.
FUEL TUBE D6x5mm -- 2 pcs
STRAPER PL4112102 -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
SERVO MOUNTING PANEL 58x64x2mm -- 1 pc.
BALSA 21x18x8mm (For Servo Mounting Panel) -- 2 pcs
7. TAIL LANDING GEAR -- 1 pc.
SCREW PA2.5x12mm -- 2 pcs
LANDING WIRE STRAPS PL4114030 -- 1 pc.
8. SOCKET HEAD SCREW M4x60mm -- 1 pc.
WHEEL Ø76mm -- 1 pc.
M4 NYLON INSERT LOCK NUT -- 1pc.
COLLAR Ø4.1mm w/ Set Screw -- 1 set
PLASTIC COLLAR Ø4.1mm -- 1 pc.
9. CABLE TIE 4x200mm -- 2 pcs
IRON 500g -- 1 pc.
AEROTOW RELEASE PUSHROD Ø2x267mm -- 1 pc.
STRAPER PL4112102 -- 1 pc.
FUEL TUBE D6x5mm -- 1 pc.
SPONGE 70x105x60mm -- 1 pc.
PVC STAND 0.5mm --pc.
PLYWOOD 70x14x8mm -- 1 pc.
PLYWOOD 70x11x8mm -- 1 pc.
10. WING TUBE Ø22x989mm -- 1 pc.
11. CANOPY -- 1 pc.
SCRATCH GUARD (OPTIONAL)-- 1 pc.
SCREW PWA2.3x8mm -- 8 pcs
SOCKET HEAD SCREW M3x10mm -- 2 pcs
WASHER d3.5xD8mm -- 2 pcs
SILICON GROMMETS PL1265035 d1.5xD6.5mm -- 8 pcs
12. DECALS: G336DEC -- 1 set
G336PO29441308

P.3
Main Wing
1
Aileron & Spoiler Servos
2
Bottom View
Apply instant type CA glue to both sides of each hinge.
Bottom View
Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole
marks at under side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
PB2x22mm Screw
4
2
16
Wire Ø3x45mm
PWA2x8mm
Pushrod
Ø1.8x50mm
3mm
2mm
2mm
2mm
Pushrod
Ø1.8x50mm
Straper
Fuel Tube
D6x5mm
Top View
Straper
Fuel Tube
D6x5mm
PWA2x8mm
PB2x22mm
Fuel Tube
D6x5mm
Clevis
Pushrod
Ø1.8x60mm
Horn
Aileron Servo & Spoiler Servo Lead
PWA2x8mm Screw
Linkage Connector
5
2
2
3
3
4
4
1
1
G336PO29441308

P.4
Stabilizer & Elevator
3
C C'
C=C'
B B'
B=B'
(Stabilizer)
(Main Wing)
A A'
A=A'
Apply instant type CA glue to both sides of
each hinge.
Completed
2
2
PM3x40mm Screw
d3.2xD12mm Washer
Temporary install the main wing, adjust leveling of the stabilizer
to make it as parallel to the main wing as possible.
PM3x40mm
Washer d3.2xD12mm
Vertical Fin & Rudder
4
Completed
G336PO29441308

P.5
Elevator Pushrod
6
Tail Landing Gear
7
Bottom View
Bottom View
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
PB2x25mm Screw
2
PA2.5x12mm
Screw
2
Rudder Pushrod
5
Bottom View
Ø1mm pilot holes for World Models horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
TWM PL8210010
CLEVIS WRENCH
PB2x30mm Screw
2
PWA2x8mm Screw
4
Clevis
Horn
Fuel Tube
D6x5mm
Pushrod
Ø1.8x165mm
PB2x30mm
TWM PL8210010
CLEVIS WRENCH
PB2x25mm
Fuel Tube
D6x5mm
Clevis
Pushrod
Ø1.8x145mm
Horn
1
Straper Fuel Tube
D6x5mm
Straper Fuel Tube
D6x5mm
PWA2x8mm
PWA2x8mm
PWA2x8mm Screw
4
PA2.5x12mm
Landing wire straps
2mm
2
2
3 4
1
2
3 4
1
G336PO29441308

P.6
Radio Equipment
9
Front
Front
Aerotow Release Servo
Aerotow Release Pushrod
Ø2x267mm
Plywood 70x14x8mm
Plywood 70x11x8mm
PVC Stand
Aerotow
Release Pushrod
Ø2x267mm
Straper Fuel Tube D6x5mm
Receiver
Sponge
Iron
Switch
Cable Tie 4x200mm
Wheel
8
Bottom View
1
1
M4x60mm Socket Head Screw
M4 Nylon Insert Lock Nut
1
4.1mm Collar
1
4.1mm Plastic Collar
M4x60 mm
4.1mm Collar
M4
Nylon Insert
Lock Nut
4.1mm
Plastic Collar
3mm
Set Screw Wheel Ø76mm
G336PO29441308

P.7
Main Wings
10
Canopy & Scratch Guard (Optional)
11
PWA2.3x8mm Screw
8
8
d1.5xD6.5mm Silicon Grommet
M3x10mm M3x10mm
Wing Tube
D22x989mm
Lead to Aileron Servo & Spoiler Servo
Tape
Completed
Completed
Bottom View
2
M3x10mm Socket Head Screw
Silicon Grommet
d1.5xD6.5mm
PWA2.3x8mm
Scratch Guard
(Optional)
Fuselage
d1.5x6.5mm
Silicon Grommet
PWA2.3x8mm
d3.5xD8mm Washer
2
G336PO29441308

P.8
Wing Seting
12
Adjust the wing and fuselage configuration as shown in the diagrams.
A=A' B=B' C=C'
C'
B'B
C
A'
A
G336PO29441308

P.9
Control Throws
13
C.G.
14
The ideal C.G. position is 116mm ( 4.57 in. ) behind the leading
edge measured at where the wing meets the fuselage. In order
to obtain the C.G. specified, add weight to the fuselage or move
the battery position. Check the C.G. before flying.
116mm
C.G.
38mm
38mm
Elevator
80mm
80mm
Rudder
20mm
20mm
Ailerons
Adjust the control throws as shown in the diagram. These throws are good for general
flying. You can adjust according to your personal preference.
4.57 in
http://www.theworldmodels.com/para/instruction/instructionManuals.php
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
Important Safety Precautions
Warning!
G336PO29441308

LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn. Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and
send toAirBorne Models, 4749-K,Bennett Drive, Livermore, CA94551 USA.
1. Name:______________________________________________
2.Address:____________________________________________
3. Phone #:____________________ E-mail:__________________
4. Model:______________________________________________
Wing QC#__________ Fuselage QC# _______________________
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:_____________________________________
6. Store Name: _________________________________________
Please callAirBorne Models at 925 3710922 for any assistance in filling this
form.Thank you very much for purchasing our product.
G336PO29441308

1/4 Scale Hall Cherokee II Wing Bag

Optional Parts
Clevis Wrench
Code No. Size Package
PL8210010 1 set
Small Clevis Large Clevis
Field Stand
Code No. Size Package
Code No. Size Package
MS9111450 600 x 240 x 350mm 1 pc
( ACCESSORIES)
180mm Extension
Code No. Size Package
KW0011800 180mm 1 set
Charge Receptacles
Code No. Size Package
KP0041300
180mm Y-Cord
Code No. Size Package
KW0021800 180mm 1 pc
Special tool for clevis installation.
Suitable for standard and small
(EP) clevis.
SV4031 40.6 x 20 x 37mm 1 set
Speed : 0.17 sec / 60° @4.8V
0.14 sec / 60° @6.0V
Torque : 3.2kg.cm / 44.8 oz - in @4.8V
4.1kg.cm / 57.4 oz - in @6.0V
Size : 40.6 x 20 x 37mm /
1.60 x 0.79 x 1.46 in
Weight : 39.4 g / 1.39 oz
Standard Servo

The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
G336PO29441308