Thrane&Thrane tt-3022d User manual

Thrane & Thrane
Thrane & ThraneThrane & Thrane
Thrane & Thrane
Fishery CapsatTransceiver
TT-3022D
Installation Manual
CopyrightThrane & Thrane A/S
ALL RIGHTS RESERVED

Information in this document is subject to change without notice
and does not represent a commitment on the part of Thrane &
Thrane A/S.
© 2000 Thrane & Thrane A/S. All right reserved. Printed in Den-
mark.
Document Number TT98-107310-D.
Release Date: 25. July 2000

Safety Summary
Safety SummarySafety Summary
Safety Summary
The following general safety precautions must be observed during all phases of
operation, service and repair of this equipment. Failure to comply with these
precautions or with specific warnings elsewhere in this manual violates safety
standards of design, manufacture and intended use of the equipment.
Thrane & Thrane A/S assumes no liability for the customers failure to comply with
these requirements.
GROUND THE EQUIPMENT
GROUND THE EQUIPMENTGROUND THE EQUIPMENT
GROUND THE EQUIPMENT
To minimise shock hazard, the equipment chassis and cabinet must be connected to
an electrical ground
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHEREDO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the equipment in the presence of flammable gases or fumes. Opera-
tion of any electrical equipment in such an environment constitutes a definite safety
hazard.
KEEP AWAY FROM LIVE CIRCUITS
KEEP AWAY FROM LIVE CIRCUITSKEEP AWAY FROM LIVE CIRCUITS
KEEP AWAY FROM LIVE CIRCUITS
Operating personnel must not remove equipment covers. Component replacement
and internal adjustment must be made by qualified maintenance personnel. Do not
replace components with the power cable connected. Under certain conditions,
dangerous voltages may exist even with the power cable removed. To avoid injuries,
always disconnect power and discharge circuits before touching them.
DO NOT SERVICE OR ADJUST ALONE
DO NOT SERVICE OR ADJUST ALONEDO NOT SERVICE OR ADJUST ALONE
DO NOT SERVICE OR ADJUST ALONE
Do not attempt internal service or adjustments unless another person, capable of
rendering first aid resuscitation, is present.
DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT
DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENTDO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT
DO NOT SUBSTITUTE PARTS OR MODIFY EQUIPMENT
Because of the danger of introducing additional hazards, do not substitute parts or
perform any unauthorized modification to the equipment.
SAFETY DISTANCE FOR THE ANTENNA UNIT
SAFETY DISTANCE FOR THE ANTENNA UNITSAFETY DISTANCE FOR THE ANTENNA UNIT
SAFETY DISTANCE FOR THE ANTENNA UNIT
Minimum safety distance of 2 feet (61 cm) from the Antenna.
Radiated intensity at 0.56m is 10 W/m2
Radiated intensity at 0.36m is 25 W/m2
Radiated intensity at 0.18m is 100 W/m2
COMPASS SAFE DISTANCE
COMPASS SAFE DISTANCECOMPASS SAFE DISTANCE
COMPASS SAFE DISTANCE
Minimum safety distance of 50 cm from the System.

This page is intentionally left blank

Table of Contents
Table of ContentsTable of Contents
Table of Contents
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page i
ii
i
Table of Contents
1 Introduction....................................................................................... 1-1
1.1 Initial inspection ....................................................................... 1-1
1.2 Storage ..................................................................................... 1-2
1.3 Repackaging for shipment........................................................ 1-2
2 Installation - TT-3022D....................................................................... 2-1
2.1 Technical specifications............................................................ 2-1
2.2 Compass Safe Distance............................................................. 2-3
2.3 Power requirements ................................................................. 2-4
2.3.1 Fuse ............................................................................ 2-4
2.4 Functional description .............................................................. 2-5
2.4.1 On/Off features ........................................................... 2-5
2.4.2 Sleep mode ................................................................. 2-5
2.4.3 Front indicators and buttons........................................ 2-6
2.5 Connectors ............................................................................... 2-8
2.5.1 Power connector ......................................................... 2-8
2.5.2 DTE Communication port .......................................... 2-10
2.5.3 I/O Connector........................................................... 2-12
2.5.4 Printer port................................................................ 2-16
2.5.5 Grounding ................................................................ 2-17
2.6 Built-in GPS (optional) ............................................................ 2-17
2.6.1 GPS specifications..................................................... 2-18
2.7 Mounting bracket ................................................................... 2-19
3 System Installation............................................................................. 3-1
3.1 Power requirements ................................................................. 3-1
3.1.1 Fuses........................................................................... 3-3
3.2 Compass Safe Distance............................................................. 3-4
3.3 Antennas................................................................................... 3-6
3.3.1 TT-3005M Maritime Antenna ....................................... 3-6
3.3.2 TT-3005B Landmobile/Fishery Antenna .................... 3-12
3.3.3 TT-3001B Option 001 Maritime Antenna.................... 3-18
3.3.4 Antenna Mounting Considerations ............................ 3-21
3.3.5 Safety Distance for Antenna Units.............................. 3-24
3.4 TT-3606C Message Terminal .................................................. 3-26
3.4.1 PCMCIA Card ........................................................... 3-26
3.4.2 ARCNET interface ..................................................... 3-26
3.4.3 AUX I/O..................................................................... 3-27

Table of Contents
Table of ContentsTable of Contents
Table of Contents
Page
PagePage
Page ii
iiii
ii 25Jul00
25Jul0025Jul00
25Jul00
3.4.4 Connector interface ...................................................3-27
3.4.5 Specifications.............................................................3-28
3.4.6 Mounting ...................................................................3-29
3.5 TT-3616A Interconnection Box (optional) ................................3-30
3.5.1 Connector interface ...................................................3-31
3.5.2 Specifications.............................................................3-34
3.5.3 Mounting ...................................................................3-35
3.6 TT-3680B Power Supply (optional) ..........................................3-36
3.6.1 Mounting ...................................................................3-37
3.7 TT-3608A Hard Copy Printer (optional)...................................3-38
3.7.1 Mounting plate...........................................................3-39
3.7.2 Roll Paper Stand.........................................................3-39
3.7.3 Mounting ...................................................................3-41
3.8 TT-3608G Printer Unit..............................................................3-42
3.8.1 Configuration.............................................................3-43
3.8.2 Installation .................................................................3-45
3.8.3 Connectors ................................................................3-45
3.8.4 Cable.........................................................................3-46
3.8.5 Specifications.............................................................3-48
3.9 TT-3042C Remote Alarm/Distress Box (optional) ....................3-49
3.9.1 Mounting ...................................................................3-52
3.10 TT-3042D Remote Alarm / Printer Unit ....................................3-55
3.10.1 Configuration.............................................................3-56
3.10.2 Installation .................................................................3-59
3.10.3 Connectors ................................................................3-59
3.10.4 Cable.........................................................................3-60
3.10.5 Specifications.............................................................3-62
3.11 Distress Button Test .................................................................3-63
3.11.1 TT-3022D Transceiver................................................3-63
3.11.2 TT-3042C Remote Alarm/Distress Box .......................3-64
3.11.3 TT-3042D Remote Alarm Distress Box ........................3-64
3.11.4 TT-3606C Message Terminal .....................................3-65
3.12 General interconnect information ...........................................3-66
3.12.1 Cable spec. diagram .................................................3-67
4 System Generation.............................................................................4-1
4.1 Terminal Mode..........................................................................4-1
4.1.1 TT-3606E Message Terminal........................................4-1
4.1.2 IBM Compatible PC .....................................................4-1
4.1.3 Computerised equipment/handheld terminals............4-2
4.2 Initialise System Parameters......................................................4-2
4.2.1 Entering your mobile number......................................4-2
4.2.2 Altering baudrate and protocol settings ......................4-3
4.2.3 Antenna voltage settings..............................................4-5

Table of Contents
Table of ContentsTable of Contents
Table of Contents
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page iii
iiiiii
iii
4.3 TT-3606C Configuration Mode ................................................. 4-6
4.3.1 DNID Selection............................................................ 4-8
4.3.2 LES Selection............................................................... 4-9
4.3.3 EGC Setup ................................................................ 4-10
4.3.4 Auto Addressing ....................................................... 4-11
4.4 TT-3606C System Menu .......................................................... 4-13
4.4.1 Format....................................................................... 4-13
4.4.2 Update Program........................................................ 4-14
4.4.3 Hardware Status ........................................................ 4-15
4.4.4 Mobile Number......................................................... 4-16
4.5 TT-3606C - System Code Update ............................................ 4-17
4.5.1 Update Method 1....................................................... 4-17
4.5.2 Update Method 2....................................................... 4-17
5 Commissioning of the equipment ...................................................... 5-1
5.1 Introduction.............................................................................. 5-1
5.2 The first Login........................................................................... 5-1
5.3 Link Test ................................................................................... 5-2
5.4 Details of a Link Test................................................................. 5-2
6 Index ................................................................................................. 6-1

Table of Contents
Table of ContentsTable of Contents
Table of Contents
Page
PagePage
Page iv
iviv
iv 25Jul00
25Jul0025Jul00
25Jul00
This page is intentionally left blank

Table of Contents
Table of ContentsTable of Contents
Table of Contents
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page v
vv
v
Table of Figures
Figure 1 TT-3022D Fishery Capsat Transceiver ........................................... 1-1
Figure 2 TT-3022D Capsat Transceiver rear panel ...................................... 2-8
Figure 3 TT-3022D Capsat Transceiver mounting plate ............................. 2-19
Figure 4 Front panel of the TT-3022D Capsat Transceiver with
mounting bracket ...................................................................................... 2-20
Figure 5 TT-3022D mounting Angle........................................................... 2-20
Figure 6 TT-3022D mounting bracket ........................................................ 2-21
Figure 7 TT-3005M Maritime Antenna ......................................................... 3-6
Figure 8 TT-3005M 1’’ Tube Mounting ....................................................... 3-10
Figure 9 TT-3005B Landmobile/Fishery Antenna....................................... 3-12
Figure 10 TT-3005B mounting holes........................................................... 3-15
Figure 11 TT-3005B Mounting.................................................................... 3-16
Figure 12 TT-3005B 1.5’’ tube mounting kit (option 001) ........................... 3-17
Figure 13 TT-3001B opt. 001 Maritime Antenna ......................................... 3-18
Figure 14 TT-3001B-opt. 001 1.5’’ Tube mounting...................................... 3-21
Figure 15 Inmarsat-C Antenna Mounting ................................................... 3-23
Figure 16 Inmarsat-C Antenna mounting near pole or funnel .................... 3-24
Figure 17 TT-3606C Message Terminal. .................................................... 3-26
Figure 18 3606C Dimensions..................................................................... 3-29
Figure 19 3606C 0pt. 920 (921) Mounting Cradle. ..................................... 3-29
Figure 20 TT-3616A Interconnection Box................................................... 3-30
Figure 21 Left: TT-3616C Factory setting , Middle: Include +5V to X5,
X6, Right: ARCNET and 5V Inverted Polarity ............................................. 3-31
Figure 22 Mounting holes for TT-3616A..................................................... 3-35
Figure 23 TT-3680B - 200W power supply. ................................................ 3-36
Figure 24 Mounting holes for TT-3680B ..................................................... 3-37
Figure 25 TT-3608A Hard copy printer ...................................................... 3-38
Figure 26 Paper Roll Stand ........................................................................ 3-39
Figure 27 Mounting holes for TT-3608A..................................................... 3-41
Figure 28 TT-3608G Remote Printer Unit ................................................... 3-42
Figure 29 TT-3042C Remote Alarm/Distress Box ....................................... 3-49
Figure 30 TT-3042C Outline drawing......................................................... 3-52

Table of Contents
Table of ContentsTable of Contents
Table of Contents
Page
PagePage
Page vi
vivi
vi 25Jul00
25Jul0025Jul00
25Jul00
Figure 31 TT-3042C Outline drawing with console bracket........................3-53
Figure 32 TT-3042C Mounting stencil.........................................................3-54
Figure 33 TT-3042D Remote Alarm Distress Box / Local Printer .................3-55
Figure 34 Interconnection diagram............................................................3-66
Figure 35 TT-3000S interconnection cable diagram (TT-3606C opt.
920)............................................................................................................3-67
Figure 36 TT-3000S with TT-3616A interconnection cable diagram (TT-
3606C opt. 921)..........................................................................................3-68
Figure 37 3606C Main Menu ........................................................................4-7
Figure 38 3606C Configuration Menu...........................................................4-7
Figure 39 3606C DNID Selection Menu ........................................................4-8
Figure 40 3606C LES Selection Menu ...........................................................4-9
Figure 41 3606C EGC Setup Menu .............................................................4-10
Figure 42 3606C Auto Addressing Menu....................................................4-11
Figure 43 3606C System Menu...................................................................4-13
Figure 44 3606C Hardware Status ..............................................................4-15
Figure 45 3606C Mobile Number Menu .....................................................4-16

Table of Contents
Table of ContentsTable of Contents
Table of Contents
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page vii
viivii
vii
Table of Tables
Table 1 TT-3022D technical specifications................................................... 2-2
Table 2 Inmarsat-C Protocol support. .......................................................... 2-3
Table 3 TT-3022D power requirements ....................................................... 2-4
Table 4 TT-3022D Capsat Transceiver ON/OFF overview ........................... 2-5
Table 5 Capsat Sleep Mode Power Requirements ....................................... 2-6
Table 6 TT-3022D Capsat Transceiver DC Power Connector pin
assignment .................................................................................................. 2-9
Table 7 Automatic baudrate settings ......................................................... 2-10
Table 8 TT-3022D X3 pin assignment......................................................... 2-11
Table 9 TT-3022D X4 pin assignment......................................................... 2-13
Table 10 Printer port (X5) pin assignment ................................................. 2-16
Table 11 GPS Specifications ...................................................................... 2-18
Table 12 Capsat System Component Power Requirements.......................... 3-2
Table 13 Capsat System Fuses..................................................................... 3-4
Table 14 Compass safe Distance ................................................................. 3-5
Table 15 TT-3005M technical specifications. ............................................... 3-8
Table 16 TT-3020C Capsat Transceiver Antenna Cable types (TNC -
TNC) for TT-3005M. ..................................................................................... 3-9
Table 17 TT-3005B Technical Specifications. ............................................. 3-13
Table 18 TT-3022D Capsat Transceiver Antenna Cable types (TNC -
TNC) for TT-3005B antenna........................................................................ 3-14
Table 19 TT-3001B opt. 001 Technical Specifications................................. 3-19
Table 20 TT-3022DCapsat Transceiver Antenna Cable types (N - TNC)
for TT-3001 opt. 001................................................................................... 3-20
Table 21 Radiated intensity ....................................................................... 3-25
Table 22 TT-3606C X1 pin assignment....................................................... 3-27
Table 23 TT-3606C Technical specifications.............................................. 3-28
Table 24 TT-3616A X1 pin assignment....................................................... 3-31
Table 25 TT-3616A X2 pin assignment....................................................... 3-32
Table 26 TT-3616A X4 pin assignment....................................................... 3-32
Table 27 : TT-3616A X5, X6 pin assignment ............................................... 3-33
Table 28 TT-3616A Technical specifications .............................................. 3-34

Table of Contents
Table of ContentsTable of Contents
Table of Contents
Page
PagePage
Page viii
viiiviii
viii 25Jul00
25Jul0025Jul00
25Jul00
Table 29 TT-3608G DIP switch settings.......................................................3-44
Table 30 TT-3608G Power Connector.........................................................3-45
Table 31 TT-3608G I/O Connector .............................................................3-46
Table 32 TT-3608G Technical Specifications ..............................................3-48
Table 33 TT-3042C and Satellite Communication Unit interconnection ......3-50
Table 34 TT-3042C Technical Specifications ..............................................3-51
Table 35 TT-3042D DIP switch settings.......................................................3-58
Table 36 TT-3042D Power Connector.........................................................3-59
Table 37 TT-3042D I/O Connector..............................................................3-60
Table 38 TT-3042D Technical Specifications ..............................................3-62
Table 39 Antenna voltage configuration.......................................................4-5

Introduction
IntroductionIntroduction
Introduction
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page 1-1
1-11-1
1-1
1Introduction
This manual provides instructions for installing, configuring and
testing of a TT-3000 Integrated Capsat System that includes a TT-
3022D Capsat Transceiver.
A wide variety of options and accessories may be linked together
with the Capsat Transceiver, and the specific installation and
configuring of these are to be found in their respective Reference
Manuals.
Figure 1 TT-3022D Fishery Capsat Transceiver
1.1 Initial inspection
WARNING
WARNINGWARNING
WARNING
To avoid hazardous electrical shock, do not perform electrical
tests if there is any sign of shipping damage to any portion of
the front or rear panel or the outer cover. Read the safety
summary at the front of this manual before installing or
operating the TT-3022D Transceiver.

Introduction
IntroductionIntroduction
Introduction
Page
PagePage
Page 1-2
1-21-2
1-2 25Jul00
25Jul0025Jul00
25Jul00
Inspect the shipping carton immediately upon receipt for evi-
dence of mishandling during the transit. If the shipping carton is
severely damaged or waterstained request that the carrier's
agent be present when opening the carton. Save the carton
packing material for future use.
Contents of the shipment should be as listed in the enclosed
packing list. If the contents are incomplete, if there is mechanical
damage or defect, or if the TT-3022D Capsat Transceiver does not
work properly, notify your dealer.
After you unpack the TT-3022D Capsat Transceiver, inspect it
thoroughly for hidden damage and loose components or fittings.
Inspect the cable harness for stress, loose or broken wires, or
broken cable tires.
Examine all the components for loose or missing hardware.
Tighten all loose hardware.
1.2 Storage
The TT-3022D may be stored or shipped in temperatures within
the limits -40° C to +80° C. It is advisable to protect the TT-3022D
from extreme temperature variation which can cause excessive
condensation. It is recommended that the TT-3022D is unpacked
immediately on delivery.
1.3 Repackaging for shipment
The shipping carton for the TT-3022D has been carefully de-
signed to protect the transceiver and its accessories during ship-
ment. This carton and its associated packing material should be
used when repackaging for shipment. Attach a tag indicating the
type of service required, return address, model number and full
serial number. Mark the carton FRAGILE to ensure careful han-
dling.

Introduction
IntroductionIntroduction
Introduction
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page 1-3
1-31-3
1-3
If the original shipping carton is not available, the following gen-
eral instructions should be used for repackaging with commer-
cially available material.
1. Wrap the TT-3022D in heavy paper or plastic. Attach a tag in-
dicating the type of service required, return address, model
number and full serial number.
2. Use a strong shipping container, e.g. a double walled carton
of 160 kg test material.
3. Protect the front- and rear panel with cardboard and insert a 7
cm to 10 cm layer of shock absorbing material between all
surfaces of the equipment and the sides of the container.
4. Seal the shipping container securely.
5. Mark the shipping container FRAGILE
FRAGILEFRAGILE
FRAGILE to ensure careful han-
dling.

Introduction
IntroductionIntroduction
Introduction
Page
PagePage
Page 1-4
1-41-4
1-4 25Jul00
25Jul0025Jul00
25Jul00
This page is intentionally left blank

Technical specifications
Technical specificationsTechnical specifications
Technical specifications Installation - TT-3022D
Installation - TT-3022DInstallation - TT-3022D
Installation - TT-3022D
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page 2-1
2-12-1
2-1
2Installation - TT-3022D
This chapter provides specific information enabling you to install
the TT-3022D Capsat Transceiver into your own system, with a
minimal effort. The default, or factory configuration is described,
together with procedures for altering this configuration.
2.1 Technical specifications
Model TT-3022D
General Specifications Meets or exceeds all INMARSAT
specifications for the Inmarsat-C
Network for non SOLAS with distress call
functions. (CN114 and IEC 945 require-
ments). It all so meets the MAF and
AMAF fishery control requirements.
EEC EMC and CE marking
Transmit Frequency 1626.5 to 1660.5 MHz.
Receive Frequency 1525.0 to 1559.0 MHz.
Channel Spacing 5 / 2.5 / 1.25 kHz.
Modulation 1200 symbols/sec BPSK.
Ambiguity Resolution Unique word.
Coding R 1/2 K=7 convolutional code, (inter-
leaved code symbols RX).
DataRate 600 bit/sec.
RX Frame Length 8.64 seconds.
TX Signalling Access Mode Slotted ALOHA.
TX Message Channel TDMA & FDMA,interleaved code
symbol.

Installation - TT-3022D
Installation - TT-3022DInstallation - TT-3022D
Installation - TT-3022D Technical specifications
Technical specificationsTechnical specifications
Technical specifications
Page
PagePage
Page 2-2
2-22-2
2-2 25Jul00
25Jul0025Jul00
25Jul00
Antenna Interface Standard 50 Ohm female TNC-connector.
Max 70m cable with TT-3005A antenna or
max 100m cable with TT-3001B or TT-
3005M antenna.
Terminal Interface EIA/TIA-232-E DTE interface. CCITT
Rec.V.24/28, 110-38400 Baud IA-5 code,
DB-9F connector.
Printer Interface Standard parallel Centronics, DB-25F
connector.IEEE P1284-I
I/O Interface: NMEA-0183 version 2.1 interface and
multidrop addressing, max.100 meter
cable.
ArcNet 156Kbit token based I/O, max
100 meter cable (ATA/ANSI 878.1)
Four dedicated In/Out pins and two
Inputs pins to the TT-3042C Remote
Alarm/Distress Box.
DB-15F connector
System Setup Flash memory
DC Power Source 10.5 to 32 V floating DC
RX: 3.8 W with GPS 4.4W
TX: Typ. 80 W max. 90W
Fuse 12A T
Ambient Temperature -25°C to 55°C operating
-40°C to 80°C storage.
Electronic Unit Mounting Mounting bracket.
Dimensions H x W x D 50mm x 180mm x 165mm. ( car radio
standard ISO7736 )
Weight 1.3 kg
Table 1 TT-3022D technical specifications.

Compass Safe Distance
Compass Safe DistanceCompass Safe Distance
Compass Safe Distance Installation - TT-3022D
Installation - TT-3022DInstallation - TT-3022D
Installation - TT-3022D
25Jul00
25Jul0025Jul00
25Jul00 Page
PagePage
Page 2-3
2-32-3
2-3
Inmarsat-C Protocol support Message transmission and reception
with IA-5, ITA-2 and binary transfer
to/from the following destinations:
Telex
PSTN (telephone modems and fax
modems)
PSDN (X.25 network)
EGC message reception with
automatical geographical area
selection
Polling and data reporting with
automatic transmission of position
reports down to a recommended
minimum of 1 per 5 minutes.
Special Access Codes
DNID Messaging
Program Unreserved Data reporting
Pre-assigned Data reporting
Transmit message size: Max 32Kbyte
Receive storage: 106 Kbyte
Non-SOLAS distress calling facilities.
Table 2 Inmarsat-C Protocol support.
2.2 Compass Safe Distance
The compass safe distance of the TT-3022D transceiver has been
measured in accordance with the standards specified in ISO/R
694, Method B. The safe distance found is 50 cm.

Installation - TT-3022D
Installation - TT-3022DInstallation - TT-3022D
Installation - TT-3022D Power requirements
Power requirementsPower requirements
Power requirements
Page
PagePage
Page 2-4
2-42-4
2-4 25Jul00
25Jul0025Jul00
25Jul00
2.3 Power requirements
The TT-3022D Fishery Capsat transceiver is designed to operate
on floating DC in the range 10 - 32 V, which makes an AC/DC
converter needed, in case the system is to work in an AC envi-
ronment.
The total power consumption varies with the particular system in
question. As a guide-line, please note the power consumption of
the following equipment:
Power requirements Receive
mode
Transmit
mode
TT-3022D Capsat Transceiver incl. TT-3005M
Antenna.
Floating DC (10-32V).
3.8W 80W
Max.
90W
TT-3022D Capsat Transceiver incl. TT-3005M
Antenna & GPS.
Floating DC (10-32V).
4.4W 80W
Max.
90W
TT-3022D Capsat Transceiver in sleep mode.
incl. Antenna
< 1mW
Table 3 TT-3022D power requirements
2.3.1 Fuse
The TT-3022D has a single fuse, which can be found on the rear
panel. In case it needs replacement a 12 A T type must be used.