Tigo TS4-A-2F Datasheet

Note: When installing TS4-A-2F, always connect the input cables to the PV modules
before connecting the TS4-A output cables in series.
1. Connect PV modules to TS4-A-2F inputs
2. Connect TS4-A-2F outputs in series
If disconnecting TS4-A-2F, always disconnect the TS4-A-2F output cables from the string
before disconnecting the input cables from the PV modules.
RSS Transmitter must be powered OFF during TS4-A-2F installation.



TS4-A-2F Installation Quick Start Guide
support.tigoenergy.com
[email protected]
International: 00800.2255.8446
Americas: +1.408.402.0802
Manual
+ +
- -
Tigo Rapid Shutdown
DONOT DISCONNECT
UNDERLOAD
4 - 123A
TS4-A-2F
+ +
- -
Tigo Rapid Shutdown
DONOT DISCONNECT
UNDERLOAD
4 - 123A
TS4-A-2F
PV Module 1
PV Module 1
PV Module 2
PV Module 2
1
2
Tigo Rapid Shutdown
DO NOT DISCONNECT
UNDER LOAD
DANGER
NEC690.12-2017and C22.1-2015 Rule64.218
For installation with frameless modules,
remove metal clips and bolt TS4-A to rail.
Removable clips
Mounting holes (M8)
If connecting 2F to a single PV module:
• Connect PV module to Input 1
• Connect Input 2 cables together

002-00066-00 09/08/2021
E469960
Photovoltaic Rapid Shutdown System Equipment, QIJW
1
3
2
Input 1
Output to string
Input 2
Tigo Rapid Shutdown
DO NOT DISCONNECT
UNDER LOAD
DANGER
NEC 690.12-2017 and C22.1-2015 Rule 64.218
1 32
PV MODULE
1
STRING PV MODULE
2
Maximum system voltage: 1500V
Maximum voltage per input: 80V
Maximum current per input: 15A
Maximum power per input: 500W
Maximum output power: 1000W
TS4-A-2F
The TS4-A-2F is the advanced add-on solution that brings rapid
shutdown functionality to two standard PV modules on
separate inputs.
If connecting 2F to a single PV module:
• Connect PV module to Input 1
• Connect Input 2 cables together
IMPORTANT NOTICE
Electricity will be supplied to the Tigo TS4-A output cables immediately when connected to a PV module
exposed to sunlight. Use care when handling.
注意事项
当连接的组件暴露在阳光下时电力将会从Tigo TS4-A输出端输出。请小心处理。
ATTENTION!
Une fois connecté au panneau photovoltaïque exposé au soleil, les boitiers Tigo TS4-A laisseront passer le
courant. Soyez vigilant.
WICHTIGER HINWEIS
Bei Verbindung der Tigo TS4-A mit einem aktiven PV-modul steht der Ausgang unmittelbar unter Spannung.
Bitte Vorsicht im Umgang.
AVVISO IMPORTANTE
Prestare la massima attenzione: i cavi di uscita dei Tigo TS4-A sono già alimentati con energia elettrica quando
vengono collegati a un modulo fotovoltaico esposto alla luce del sole.
안전을 위 한 주의사항
햇빛에 노출된 태양전지 모듈에 연결하면 Tigo TS4-A 출력 케이블에즉 시 전기가 흐르게 됩니다.취급시 주의하십시요.
重要事項
日射下の太陽光モジュールを接続すると同時に、タイゴTS4-Aの出力 ケーブルにも電気が流れますので、取扱いには十分
ご注意ください。
¡PRECAUCION!
Al momento de conectar los cabels de salida los Tigo TS4-A a un módulo fotovoltaico expuesto al sol, se iniciarà
la corriente eléctrica. Tenga cuidado en su manejo.
TS4-A-2F
Class II double insulation
High Voltage
DANGER
Requires Tigo RSS Transmitter for rapid shutdown control.
Output voltage is 0.6V when RSS Transmitter signal is not present.
If string is disconnected under load, wait 1 minute before reconnecting TS4-A-F.
Verify that output voltage is 0.6V before reconnecting.
Use ANSI/NFPA 70 wiring methods.
Modules must not be installed in readily accessible locations. (Canada only)
Connectors from different manufacturers cannot be mated with each other.