Time4Sleep SANTORINI BEDSTEAD User manual

16
7
8
Headboard
Footboard
Side Rails
Angle Brackets
Wooden Legs
2
Centre Support Bar
Centre Support Bar Legs
24/26
924/26
10
Wooden Slats
Single Plastic Caps
Double Plastic Caps
12/13
Ref. Qty
Ref. Description
5
SANTORINI BEDSTEAD
Double and King Size
Parts Identification
Qty
1
2
3
1
1
2
Parts Checklist
Description
4 4
Page 1 of 5
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
diovaot,ylbmessagnirudnerdlihcgnuoymorfyawatpek
the danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
4
180822
1
2
3
3
4
5
6
77
9
10
8
Double/King
Double/King
Double/King

Fittings Checklist
Page 2 of 5
QtyCode Description
Ax28
C
x28
Spring Washers (for M8 bolts)
D
Qty
Code Description
B
Allen Key (for M8 bolt) x1
Bolts (M8x30mm) for
fitting side rails (3) and to
headboard & footboard (1&2)
Flat Washers (for M8 bolts)
x8
F
M8 nuts for fixing Legs (5) to
corner brackets (4) and fitting
centre bar support legs (7)
HARDWARE NEEDED FOR BED ASSEMBLY
x36
x4
E
Bolts (M8x40mm) for fitting
Centre Support Bar Legs (7) to
Centre Support Bar (6)
Additional Tools Required
Care & Maintenance
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
General Hints & Tips
A ssembly requires two persons.
Approximate time to
assemble this product
1.5 Hrs
In the unlikely event of missing or damaged parts,
please contact your retailer. Please have this guide at
hand quoting the part code reference numbers shown
when requesting spare or replacement parts.
G
x1
Spanner (for M8 nut)

Stage
1
Page 3 of 5
A x12 B x8 C x12
D
x1
2
1
Fit two sets of bolts (A), spring washers (B), and flat washers (C) to the holes in the headboard (1) and footboard (2) as shown.
Note: Do not tighten fully but leave 10mm protruding as in the diagram.
Fit the side rails (3) to the headboard and footboard locating the brackets behind the flat washers.
Loosely screw in the bolts but do not tighten them 100% yet.
A
B
C
10mm
3
1
&
2
3
3
6
CC
Footboard (2)
Headboard (1) Fit bolts (A) and flat
washers (C) carefully
fixing centre support
bar to headboard &
footboard. Make certain
holes for slats point
upwards. Please take
care not to damage the
fabric.
AA
Bed Assembly

Stage
2
Page 4 of 5
A x16 B x16 C x16
D
x1
Stage
3
C x8
D
x1
Bed Assembly
G
D
F
C
E
G x1
F
x8
E x4
7
7
5
7
Once all four corners are located,
make sure the bed is square as
in the sketch,
then tighten all the
bolts 100% using allen key (D).
MAKE CERTAIN THE BED IS
SQUARED
UP, AS SHOWN IN THE DIAGRAM.
C
B
F
G
B x4
A
B
C
D

Stage
4
Page 5 of 5
Bed Assembly
9
98
8
8
810
DOUBLE SIZE
KING SIZE
3
6
Fit single plastic caps (9) to each end of a pair
of slats (8) then slide into the double cap (10)
in the centre.
Connect each set onto centre support bar (6)
& the supports on the side rails (3) - carefully
align the lugs & tap gently with a light hammer.