Timewatch Ultrafp804 series User manual

Quick Start Guide

3Activation

Mounting Screw

Appearance

Installation

1. Install 120 or 86gang box into the wall.

2. Route the cables through the cable hole of

the mounng plate.

3. Secure the device mounng plate on the gang

box with two screws. (Supplied).

4. Connect the corresponding cables.

5. Align the terminal with mounng plate. Push the

terminal in the mounng plate from boom up.

Fasten the terminal with the buckles on the plate.

4. Tighten the screws to ﬁx the terminal on the

mounng plate and complete the installaon.

The default values of the terminal are as follows:

• The default IP address: 192.0.0.64

• The default port No.: 8000

• The default user name: admin

Activating via Device

Power on and wire the network cable aer installaon.

You should acvate the device before the ﬁrst login.

Aer powering on, the interface will be displayed as

follows.

You can create the device password and conﬁrm the

password to acvate.

2.4-inch LCD Display Screen Indicator

Keypad

Fingerprint

Reading Module

Door Bell

Buon

12V

Power Interface

USB Interface/

Reset Buon

(Inside of the Cover)

Ethernet Port Door Lock

Wiring Terminal

Alarm

Wiring Terminal

RS-485/Wiegand Wiring Terminal

Tamper-proof

Buon

ESC OK

ABC

DEF

GHI

MNO

PQRS

TUV

WXYZ

JKL

Exing Key

Direcon Keys

Numeric Keys/

Leer Keys

OK Key

Eding Key

Deleng

Key

Anticlockwise Rotation

[Number]

OK Next Input Method

Device Acvaon

Acvaon Password (8 to 16 Characters)

Keypad Descriptions

OK Key: Press to conﬁrm operaons. Hold the key for 2 s to enter the

Deleting Key: Press the key to delete the entered leer or number.

Numeric Keys/Letter Keys: Enter numbers or leers.Key 0 can also

represent a space key except you are using the number input method.

Exiting Key: Press the key to exit the menu.

Direction Keys: Press , , and to move the cursor.

Editing Key: Press the key to enter the number 0. Hold the key to shi

among numbers/lowercases, numbers/uppercases and symbols.

Doorbell Button: Press the doorbell buon and the doorbell rings.

Notes:

1. The pictures here are for reference only. Some models do not support card swiping

funcon. For details, refer to the actual products.

2. If you enable the aendance status funcon, the OK key, the direcon key, and the

exing key can be the shortcut key of the aendance status.

UltraFP804 Series Fingerprint Access Control Terminal

4ConfigurationDevice Wiring

Attendance Configuration

Access Control System Configuration

User Management

Note: The external power supply and the access control terminal should use the same GND cable.

Manage User: In the New (New User) interface, enter

the new user ID No., the user name, the card No. Register

the ﬁngerprint, set the password, select the department,

set the user permission, select schedule template, set the

authencaon mode and set the duress card. Save the

parameters to conﬁrm adding.

ACS System Configuration:

In the ACS Parameters Seng interface, conﬁgure the terminal authencaon mode, the sub reader authen-

caon mode, the door magnec status, the lock acon me, the door-open meout alarm, and the maximum

mes for authencaon.

Holiday Group Configuration:

In New (New Holiday Group) interface, enter a new holiday group name. Select New ACS Holiday and enter

the holiday No., the holiday name, the holiday start me and the holiday end me. Save the parameters to

conﬁrm adding.

Week Plan Configuration:

In the Week Plan menu, select New (New Week Plan) to conﬁgure the week plan parameters, including the

No., the name, the week plan me and the corresponding periods. Save the parameters to conﬁrm adding.

Schedule Template Configuration:

In the Schedule Template menu, select New (New Schedule Template) to conﬁgure the schedule template

parameters, including the template No., the template name, the week plan and the holiday group. Save the

parameters to conﬁrm adding.

Conﬁgure the shi via the device. You are able to

schedule shi by department or by individual depending

on the user property. The working ﬂows are as follows:

Scheduling Shift by Department: Add User (See

Step 1) - Edit Department - Conﬁgure Shi - Add Holiday -

Conﬁgure Shi Schedule (by Department).

Edit Department: Select a department to edit in the department list. Select “Edit”and edit the department name, shi type and shi name. Save the parameters

Configure Shift

Normal Shi: In the Normal Shi interface, conﬁgure the aendance rule, the normal shi aendance. Save the parameters to conﬁrm seng.

Man-Hour Shi: In the Man-Hour Shi interface, conﬁgure the man-hour shi parameters. Save the parameters to conﬁrm seng.

Add Holiday

In the New (New Holiday) interface, enter the holiday No, the holiday name, the holiday start me and the holiday end me. Save the parameters to conﬁrm adding.

Configure Shift Schedule

Schedule Shi by Department: Select a department to conﬁgure in the By Dept. (Schedule by Department) interface. Conﬁgure the shi, the start date, the end date and

the holiday. Save the parameters to conﬁrm conﬁguraon.

Schedule Shi by Individual: Select New Individual Shi in the By Indiv. (Schedule by Individual) interface. Select a person to schedule in the New Individual Shi

interface. Conﬁgure the shi, the schedule start date and the end date. Save the parameters to conﬁrm eding.

User Management

ACS Conﬁguraon

Aendance

Conﬁguraon

External Device Wiring Overview (Without Secure Door Control Unit)

External Device Wiring Overview (With Secure Door Control Unit)

Secure Door Control Unit

Wiring Terminal

Note: The external power supply and the secure door control terminal should use the same GND cable.

Attendance Report

Plug the USB disk in the device. In Report interface of Aendance interface, select a table type to export. Press the OK key to export the aendance report to the USB disk.

The device will automacally check the USB disk memory. If there is no enough space for exporng, a prompt will be displayed. You are able to conﬁgure the record over

threshold prompt and record delete funcon in the System interface.

Record over Threshold Pop up Prompt (%): If the aendance record memory reaches the conﬁgured value, the system will pop up a prompt to remind you. If

conﬁgure the threshold to 99%, the system will pop up a prompt to remind you to delete the aendance data when the capacity reaches the threshold. The available

value: 1 to 99.

Record Delete: When the funcon is enabled, the terminal will delete the ﬁrst 3000 aendance records when the memory is full, in order to save the new aendance

records. By default, the funcon is enabled. See Secon 5.2 Aendance Record Delete Rule in the User Manual of Fingerprint Time Aendance Terminal.

Scheduling Shift by Individual: Add User (See Step 1) - Conﬁgure Shi - Add Holiday - Conﬁgure Shi Schedule (by Individual).

User Management, Access Control System Conﬁguraon

and Aendance Conﬁguraon are three main parts of the

Access Control Terminal.

Exit Buon

Power Input

SENSOR

BUTTON

Green/Brown

Black

Green/Black