TIS TIS-DMX-48 User manual

This product is a controller supporting 48 ballasts
for scene control and grouped and individual lights
control using the DMX standard.
PRODUCT INFORMATION
PRODUCT SPECIFICATIONS
Ports DMX Standard DMX connection
TIS Bus
Number of devices on 1 line Max. 64
Bus voltage 12-32 V DC
Current consumption <25 mA / 24 V DC
Protection Reverse polarity protection
Function
programmable options
DMX
Numbers of areas 24
12 Scenes
16 Sequence
Dimensions Width × length × height 76mm × 73mm × 90mm
Housing
Materials Fireproof ABS
Casing color Black
IP rating IP 20
6 58921 79854 6
BARCODE (UPC-A)
DMX MASTER CONTROLLER
Din-rail DMX Actuator
INSTALLATION MANUAL
Model: TIS-DMX-48

INSTALLATION MANUAL
MODEL : TIS-DMX-48
DMX MASTER CONTROLLER
2
www.tiscontrol.com
TIS CONTROL LIMITED
Wanchai, Hong Kong
TIS CONTROL PTY LIMITED
SA , AUSTRALIA
Copyright © 2022 TIS, All Rights Reserved
TIS Logo is registered trademark of TIS CONTROL.
All of the specification are subject to change without notice.
Mounting Location
Install in a dry, well-ventilated location.
Controllers may emit some mechanical
noise. Take this into account when deciding
on a mounting location.
Data Cable
Use screened stranded RS485 data cable
with four twisted pairs. Congure devices in
a “Daisy Chain.”
Do not cut or terminate live data cables.
Warranty
We provide a warranty as required by law.
A hologram warranty seal and product
serial number are provided on each device.
Please send the description of the defect
with Product S/N to our dealer network.
Read Instructions
We recommend that you read this
Instruction Manual before installation.
Safety instructions
Electrical equipment should only be
installed and tted by electrically skilled
persons.
Failure to observe the instructions may
cause damage to the device and other
hazards.
These instructions are an integral part of
the product and must remain with the end
customer.
Programming
Advanced programming requires TIS
Device Search software. Advanced
software programming knowledge should
be obtained in the advanced training
courses.
Simple Installation
DIN Rail mount facilitates installation.
Fixing points are provided for installation
without the use of DIN rail.

INSTALLATION MANUAL
MODEL : TIS-DMX-48
DMX MASTER CONTROLLER
3
www.tiscontrol.com
TIS CONTROL LIMITED
Wanchai, Hong Kong
TIS CONTROL PTY LIMITED
SA , AUSTRALIA
Copyright © 2022 TIS, All Rights Reserved
TIS Logo is registered trademark of TIS CONTROL.
All of the specification are subject to change without notice.
Turn Off TIS Power supply
1WARNING! HIGH VOLTAGE
INSTALLATION STEPS
Mount the device on a DIN rail inside an
approved enclosure. The device can also
be installed without the use of DIN rail by
two mounting screw holes.
2
+24D+D-GND+24D+D-GND
Connect a Cat5e TIS network data
cable to the TIS-BUS port as per the
connection diagram. No need to loop the
TIS-bus cable if 2 DIN Rail modules are
connected together from the side bus
train terminal.
3
To the TIS BUS Network
Cat5e
TIS-DMX-48
TIS-BUS
PRG
NET
32
1
DMX
GND D+ +24V
D-
+24V
D-
GND D+
GND(white-orange)&(white-brown)
D-(white-green)&(white-blue)
D+(blue-green)
+24V(brown-orange)
Cat5e connection

INSTALLATION MANUAL
MODEL : TIS-DMX-48
DMX MASTER CONTROLLER
4
www.tiscontrol.com
TIS CONTROL LIMITED
Wanchai, Hong Kong
TIS CONTROL PTY LIMITED
SA , AUSTRALIA
Copyright © 2022 TIS, All Rights Reserved
TIS Logo is registered trademark of TIS CONTROL.
All of the specification are subject to change without notice.
Turn on TIS power supply. The module’s
PRG LED should start blinking.
5
INSTALLATION STEPS
TIS-DMX-48
TIS-BUS
PRG
NET
32
1
DMX
GND D+ +24V
D-
+24V
D-
GND D+
Connect DMX terminal (see DMX female
connectors type) 1, 2, 3 pins to the DMX
GND (1), D- (2), and D+ (3) in the TIS
module.
4
1 1
2
2
33
4
5
Male Connector Viewed from Front
DMX IN DMX OUT
To the TIS BUS Network
DMX Cable
GND
D -
D +
GND(white-orange)&(white-brown)
D-(white-green)&(white-blue)
D+(blue-green)
+24V(brown-orange)
Cat5e connection

INSTALLATION MANUAL
MODEL : TIS-DMX-48
DMX MASTER CONTROLLER
5
www.tiscontrol.com
TIS CONTROL LIMITED
Wanchai, Hong Kong
TIS CONTROL PTY LIMITED
SA , AUSTRALIA
Copyright © 2022 TIS, All Rights Reserved
TIS Logo is registered trademark of TIS CONTROL.
All of the specification are subject to change without notice.
TROUBLESHOOTING
PRG Button Blinks Red Color
Rapidly
Reason: The Module address conicts with
other device in TIS network, you need to
press and hold the PRG button for 6 seconds
so the module can get new address
Device PRG LED is not Blinking;
Device not Powered
Reason: Device is not powered on; no TIS-
BUS 24V supply connected to the device.
Wall Panels can’t Control the
Device Channels
Reason 1: TIS-BUS connection has a
problem; check the wires and make sure
there’s not a short circuit in the connection.
Reason 2: Programming address is wrong.
Device cannot control DMX
devices
Reason 1: There is a short circuit in the DMX
connection.
Reason 2: The address of the DMX device
does not match what is programmed in the
software.