TKH security PD1022v2 User manual

© TKH Security B.V.
PD1022v2
2MP Network PTZ Dome Camera
Quick Start Guide
Unpack Installation Notices Connectors
SD Card & Default Default Button Camera Cabling
Find additional manuals, the
datasheet, the EU Declaration of
Conformity, and the latest firmware
for this product at:
tkhsecurity.com
CAUTION INSTALLATION SHALL BE PERFORMED BY
QUALIFIED PERSONNEL ONLY. INSTALLATION SHALL BE IN
ACCORDANCE WITH LOCAL PROCEDURES. THE CAMERA
CONTAINS BATTERIES. DO NOT REPLACE IN RISK OF
EXPLOSION.
BATTERY REPLACEMENT SHALL NOT BE APPLIED IN VIEW
OF THE RISK OF EXPLOSION. LE REMPLACEMENT DES
PILES NE DOIT PAS ÊTRE APPLIQUÉ AU RISQUE
D'EXPLOSION. DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS. METTRE AU REBUT LES
BATTERIES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS..
FOR “PoE” INPUT CONNECTION, USE ONLY WITH UL
LISTED I.T.E WITH “PoE” OUTPUT. DESCRIPTION FOR THE
“PoE” IS INTENDED TO BE CONNECTED TO NOT EXPOSED
(OUTSIDE PLANT) NETWORKS OR EQUIVALENT
STATEMENT IN INSTALLAION INSTRUCTIONS.
POUR LA CONNEXION DâÇÖENTREE "PoE", UTILISER
UNIQUEMENT AVEC UN I.T.E. LISTE AVEC UNE SORTIE
"PoE". LA DESCRIPTION DE "POE" EST CONÇUE POUR
ÊTRE CONNECTÉE À DES RÉSEAUX OR NON ÉNONCÉS
(INSTALLATIONS EXTÉRIEURES), DANS LES
INSTRUCTIONS D’INSTALLATION DE L’INSTALLATION.
Subject to modification. Actual product and accessories may differ in appearance.
Figure 1 Camera Connectors
2021 | Vision 1 (20210921) | PD1022v2 QSG
RJ-45 Port
802.3at PoE+
Alarm in
Alarm Out
Audio I/O
Power (DC12V)
Ground
14-pin Alarm/Audio
I/O terminal block
Quick Start Guide
Camera Unit
Security Torx
Screws(4x) &
Plastic Screw
Anchors (4x)
Gland Sets Combi-connector 3-
pin(2x), 4-pin(1x)
Silicone Plug
Decorative Rim
Memory Card Slot
Memory Card Cover
Remove the silicon plug and
unscrew 4x to remove cover
Remove memory card cover
and insert Micro
SD/SDHC/SDXC up to
128GB / Jusqu'à 128 GO
Table 1 Connector definition
No.
Connector Definition
1
Alarm I/O
Alarm I/O connection
2
Audio I/O
Line In and Line Out connection
3
RJ
-45 Port
(Contact Siqura for a
compatible PoE
injecter.)
For network and PoE connections
4
Power(DC 12V)
Power Connection
5
Reset Button
Press the button with a proper tool for at
least 20 seconds to restore the system.
6
Micro SD
Card Slot
Insert the SD card into the card slot to store
videos and snapshots. Do not remove the
SD card when the camera is powered on.
1
2
3
4
5
Figure 3 –Position of default button
Press the button with a proper
tool for at least 20 seconds to
restore the system.

© TKH Security B.V.
Auto detect with SDM2
Browser-based Viewer
Accessing the Camera - DHCP
1st time camera login
Accessing the camera –Fixed IP
1st time camera login
Tkhsecurity.com
Enter to the camera
product page, Link &
Download section
IP = 10.x.y.z
Network Switch
DHCP
1
2 3
SDM2-vx.xx-setup.zip
Look for SDM2
x6W@oM0a!9#F
11
Set a strong password
qwer1234
x6W@oM0a!9#F
IP = 192.168.1.x
IP = 192.168.1.x
Network Switch
DHCP
30s
DHCP
IP = 10.x.y.z
2021 | Vision 1 (20210921) | PD1022 QSG
IT IS NOT RECOMMENDED TO CONTINUOUSLY
(24/7) RECORD WITH THE MICRO SD CARD, AS
THE CAMERA MAY NOT SUPPORT LONG-TERM
CONTINOUS DATA READ/WRITE. CONTACT THE
MANUFACTURER OF THE MICRO SD CARD FOR
INFORMATION REGARDING THE RELIABILITY
AND THE LIFE EXPECTANCY.