TKH security PD980 User manual

Unpack
Connector Definition
Installation Notices Connectors
Camera Cabling (2)
Camera Cabling (1)
PD980
8MP Pendant PTZ Camera
Quick Start Guide
Find additional manuals, the datasheet,
the EU Declaration of Conformity, and
the latest firmware for this product at:
https://tkhsecurity.com/
Camera Unit
Note 1: Subject to modification. Actual product and accessories may differ in appearance.
Figure 2 Camera Connectors
NOTE:
It is not recommended to continuously (24/7) record with the micro-SD card, as
the camera may not support long-term continuous data read/write. Contact the
manufacturer of the micro-SD card for information regarding the reliability and
the life expectancy.
For the connector definitions, see table 1.
No.
Connector
Definition
1
RJ
-45 Port
(Contact TKH Security for a
compatible PoE injector.)
For network and PoE (802.3bt) connections
2
Power (AC24V)
AC24V power connection
3
Reset Button
Press the button with a proper tool for at
least 20 seconds to restore the system.
4
Audio/Alarm I/O & RS
-485
Audio/Alarm I/O & RS
-485 connection
5
BNC
For analog video output
6
SD Card Slot
Insert the SD card into the card slot to
store videos and snapshots. Do not
remove the SD card when the camera
is powered on.
Table 1 Connector Definition
Pin
Definition
1
AC24V L
2
GND
3
AC24V N
Table 3 Pin definition for AC24V power connection
Power Connector (AC 24V)
NOTE: In some cases, an ethernet crossover cable may be needed when
connecting the camera directly to the pc. Check the status of the link indicator
and the activity indicator LEDs. If the LEDs are unlit, check the LAN connection.
NOTE: Do not replace batteries of the camera. Risk of explosion may
occur if the battery is replaced by an incorrect type.
NOTE: Leaving a camera in an extremely high temperature surrounding
environment can result in an explosion or the leakage of flammable liquid
or gas.
NOTE: Camera subjected to extremely low air pressure may result in an
explosion or the leakage of flammable liquid or gas.
NOTE: The means of power cord of adapter should be connected to a
socket-outlet with earthing connection.
PoE and Ethernet cable connection
❑The green link LED is lit when there is a good network
connection.
❑The orange network LED flashes to indicate that there is
network activity.
CAUTION:
Installation shall be performed by qualified personnel only.
Installation shall be in acccordance with local procedures.
Installation with poe shall be in unexposed networks.
Battery replacement shall not be applied in view of the risk of explosion.
If you use an external power supply, contact TKH Security to make sure that the
power supply has the proper power specifications.
Make sure that the power supply complies with LPS requirements.
When installing the camera, hook up the camera with the anti-drop chain of the
pendant to the anti-drop ring (see figure 1). For more information, contact TKH
Security.
WARNING: For “PoE” input connection, use only with UL listed I.T.E. with “PoE”
output. Description for the “PoE” is intended to be connected to not exposed
(outside plant) networks or equivalent statement in installation instructions.
POWER RATING: 24VAC, 50-60Hz, 3.26A shall be supplied by power adapter. 55VDC,
0.93A shall be supplied by “PoE” (802.3bt type 3 class 6).
NOTE: Explosion may occur due to disposal of a battery into fire or a hot
oven, or mechanically crushing or cutting of a battery.
NOTE: The wiring of input terminal block should be installed by skilled
personnel.
NOTE: Use wire size ranging from 16 to 24 AWG (and wire type: Cu)
ONLY.
NOTE: The recommended tightening torque is 0.5 N-m.
NOTE: Use of controls or adjustments of performance or procedures other than
those specified herein may result in hazardous radiation exposure.
© TKH Security B.V. 2022-2023 | Version 1.4 (20230623) | PD980 QSG
M4 security screw
with rubber
14-pin Alarm/Audio I/O
terminal block
Quick Start Guide
3-pin power
terminal block
(AC24V use)
Grommet
Grommet holder
RJ45
insertion
tool
Figure 1 Position anti-drop ring and anti-drop chain

Audio/Alarm I/O and RS-485 connection Accessing the camera Auto detect with SDM2
1st time camera login Install browser-based viewer Browser-based Viewer
See the diagram and the pin definitions below for the
Audio/Alarm I/O and RS-485 connection.
Figure 3 Diagram of Audio/Alarm I/O and RS-485 connection pins
Pin
Definition
Pin
Definition
1
Audio
Out 8
RS
-485 D-
2
GND
(Audio I/O) 9
Alarm
In 4
3
Alarm
Out A1 10
Alarm
In 3
4
Alarm
Out A2 11
Alarm
In 2
5
Alarm
Out B1 12
Alarm
In 1
6
Alarm
Out B2 13
GND
(Alarm I/O and RS-485)
7
RS
-485 D+ 14
Audio
In
Table 3 Pin definitions for Audio/Alarm I/O and RS-485 connection
Figure 4 shows the main page of the IP camera user interface.
Figure 4 Main page IP camera user interface
Note 1: If the IE web interface is not showing video, you might need to open your
firewall or set the OCX protocol to RTP-over-RTSP(TCP).
IP = 10.1.1.1
Netmask: 255.0.0.0
IP = 10.x.y.z
Network Switch
DHCP
23
1
1
2
Admin
1234
qwer1234
x6W@oM0a!9#F
Set a strong password
11
3
4
x6W@oM0a!9#F
https://tkhsecurity.com/
Enter to the camera product
page.
SDM2-vx.xx-setup.zip