Toa CI-600 User manual

INSTALLATION MANUAL
COMPUTER INTERFACE CI-600
To obtain optimum results from this computer interface, please follow instructions in this manual
carefully. We suggest that you keep this manual handy for future reference.
CONTENTS
GENERAL DESCRIPTION...................................................... 1
PART NAMES....................................................................... 1
INSTALLATION..................................................................... 2
CONNECTION
Input control connector and DC power supply ........... 3
Speech IN/OUT terminals.......................................... 3
RS-232C connection.................................................. 4
BACK-UP BATTERY.............................................................. 5
INITIAL SET-UP OF CI-600 ................................................... 6
SPECIFICATIONS................................................................. 7
ACCESSORIES..................................................................... 7

GENERAL DESCRIPTION
The Toa CI-600 Computer Interface is used in conjunction with the SI-62 Speech Interface
and the EX-610, EX-620 or EX-630 exchange. Connected to a personal computer or data
terminal, the CI-600 permits system programming, personal information display, release
of fixed messages, etc.
PART NAMES
[Front-mounted facilities)
Knob
CI-600 without cover
* Each DIP switch is OFF when put downward and ON when put upward, with the switch
numbers 1 through 8 allocated left to right.
[Rear-mounted facilities)
RS-232C connecto r Input control connector Power input terminal
(CN1, CN2)
Speech IN/OUT terminal
SI-62
Ni-Cd battery
BAUD RATE DIP switch
*
Cover
Timer indicator MODE SELECT DIP switch *
- 1 -- 1 -

1.Rack mounting (exchange is mounted in an equipment rack.)
Attach the supplied brackets to the CI-600 to mount in a rack. See the figure.
Fiber washer
M5 tapping screw
M3 binding head screw
M3 washer
2. Desk-top applications
Attach the supplied rubber foot to the position indicated with a small hole (4 holes 2.4mm
in diameter) in the bottom plate.
- 2 -
INSTALLATION

CONNECTION
1. Input control connector and power supply
Use the connection cable YR-806
(100cm in length) for connection
between the CI-600 and
exchange. When placing the
CI-600 on the exchange, use the
YR-802 cable (40cm).
Use the YR-803 or YR-807 cable
to connect the CI-600 to other
equipment.
For input control connector, use
either CN-1 or CN-2. They are
internally connected in parallel.
2. Speech IN/OUT terminals
Connect the IN/OUT terminals to the BX-610 or BX-620 terminal box as illustrated below.
IN 2 to No. 215 (upper row)
OUT 2 to No. 215 (lower row)
To other equipment
YR-802 or YR-806
Interface connector
CI-600
Be sure to insert the SI-62
Speech Interface card into the
second slot of a opening
allocated to the LM unit.
BX-610/BX-620
- 3 -

3. RS-232C connector
Connection between CI-600 and DEC VT-100 terminal
Connect the DEC terminal and CI-600 using the appropriate cable for distance between
the two. The type of connector is D-sub 25 pins (male) and D-sub 25 pin (female).
RS-232C 25-pin connector
M : Male connector
F : Female connector
[Connection diagram]
RS-232C
25-pin
connector
DEC terminal
RS-232C
Connection between IBM personal computer and CI-600
Connect the IBM personal computer and CI-600 using the appropriate cable for distance
between the two. The type of connector is D-sub 25 pins (male) and D-sub 25 pins
(female).
RS-232C 25-pin connector
[Connection diagram]
M : Male connector
F : Female connector
Personal computer
RS-232C
- 4 -

Connection between Cl-600s (tie-line connection)
In a tie-line system, connect one Cl-600's RS-232C connector No.2 t o the same connector
of another CI-600 only when initial set-up is performed.
(Refer to the operating instructions.)
[Connection diagram]
BACK-UPBATTERY
The Ni-Cd battery (GB50-3FA1) maintains the Cl-600's stored data during power failure.
Observe the following precautions.
To keep the battery fully charged, do not switch power off for first 8 days
after installing the Cl-600. Once the battery has been fully charged, it maintains
the stored data for about 10 days (at 25°C) even no power is supplied.
Expected battery life is about 2 years (at 25°C). Replace the battery every 2 years.
- 5 -

INITIAL CHECK-UP OF CI-600
START
Connect IN/OUT lines, power lines and speech IN/OUT lines to both the exchange and CI-600.
Using the RS-232C cable, connect Cl-600's RS-232C connector No. 1 to
personal computer or data terminal.
Set both MODE SELECT and BAUD RATE DP switches.
(Refer to the operating instructions.)
Set personal computer or data terminal in accordance with the Cl-600's
format. (Refer to the operating instructions.)
• Make sure that power is
supplied.
• Set reset switch (MODE
SELECT switch No.7) to ON.
Switch on the CI-600.
Does the timer LED blink at
1-second interval ?
NO
YES
Does the monitor display initial set-up menu ?
YES NO
Can characters typed from a
keyboard be correctly displayed
on the screen ?
Confirm that the RS-232C
connector is connected properly.
NO
YES
Recheck if MODE SELECT
switch NQ 7 is set to OFF. *
Confirm that the communication
format of personal computer or
data terminal matches that of
CI-600.
The section "Initial setting" of
operating instructions.
IMPORTANT
Leaving the switch on will cancel all
the stored data when power is
switched again.
- 6 -

Rack mounting bracket
Rack mounting screw (M5×12)
Fiber washer
Binding head screw (M3×6)
Washer (M3)
Rubber foot
Floppy disk
ACCESSORIES
SPECIFICATIONS
Specifications are subject to change without notice.
133-06-174-50
2
4
4
4
4
4
2
Operating power voltage
Current consumption
Terminal capacity
IN-OUT connector/terminal
Standard
Message capacity
Recording & reproduction
Ambient temperature
Dimensions
Weight
24V DC (20-28V)
Less than 300mA
3
Interface bus
RS-232C
Speech IN/OUT/power unit
2
3
1
RS-232C
1.5-sec message×10
0.75-sec message × 10 (Total 22 sec)
ADM method
0°C~40°C
432(W)×44.5(H)×298CD)mm
(17(W)×1.8(H)×11.7(D) inch)
3.3kg (7.3 lbs)