Toro 117-9170 User manual

FormNo.3395-948RevA
FenderKit
Groundsmaster7200SeriesTractionUnit
ModelNo.117–9170
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
DescriptionQty.Use
Fendermount1
Rightfender1
Thread-formingscrew(5/16x5/8inch)2
Bolt(1/4x5/8inch)2
Nut(1/4inch)2
Installtherightfender.
Leftfender1
Nut(3/8inch)2
Bolt(3/8x3/4inch)2
Installtheleftfender.
PreparingtheMachine
1.Positionasuitableoorjackundertherearbumper
tubeandraisethereartiresofftheground(Figure1).
Note:Positionthejackstandsundertherearbumper.
Figure1
1.Rearbumpertube2.Floorjack
2.Removetherearwheels.
3.Removealldebrisfromthewheel-wellarea,including
anydebriscaughtinthebrakeassembly.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3395-948*A

InstallingtheRightFender
1.Removetheboltsecuringthehoseclamptotheframe
channelontherightsideofthemachine(Figure2).
Figure2
1.Hoseclamp2.Bolt
2.Insertthebottomofthehoseclampthroughtheslot
inthetopofthefendermount(Figure3).
Figure3
1.Fendermount
3.Looselymountthehoseclampandfendermountto
theframechannelwiththeboltpreviouslyremoved.
4.Positiontheframemounthorizontallyontheframe
channel.
5.Usetheframemountasatemplatetolocateandmark
theother2fendermountingholesintheframechannel
(Figure4).
Figure4
1.Markhere.
6.Removetheboltandnutsecuringtheclampandfender
mounttotheframe(Figure5).
Figure5
1.Drillhere.
7.Atthelocationsthatyoumarkedinstep5,drill2holes
(.281-inchdiameter)throughtheframechannel(Figure
5).
8.Looselymountthehoseclampandfendermountto
theframechannelwiththehoseclamp,bolt,andnut
(seeFigure3).
2

9.Usingthenewlydrilledholes,securethefendermount
totheframechannelwith2thread-formingscrews
(5/16x5/8inch)asshowninFigure6.
Figure6
1.Thread-formingscrew(5/16x5/8inch)
10.Tightenallthefasteners.
11.Looselymountthesideoftherightfendertothe
fendermountwith2bolts(1/4x5/8inch)and2nuts
(1/4inch)asshowninFigure7.
Figure7
1.Rightfender3.Nut(1/4inch)
2.Bolt(1/4x5/8inch)
12.Looselymountthebracket,onthetopofthefender,to
thefueltankbracketwith2bolts(3/8x3/4inch)and
2angenuts(3/8inch)asshowninFigure7.
Note:Makesurethatthefenderisnotrubbingonthe
brakerotorandtightenthefasteners.
InstallingtheLeftFender
1.Disconnectthecablefromthenegativeterminalof
thebattery.
2.Disconnectthecablefromthepositiveterminalof
thebattery.
3.Removethecarriagebolt,washer,batteryhold-down,
andnutsecuringthebattery(Figure8).
Note:Retainthehold-downandthefasteners.
Figure8
1.Batteryhold-down2.Batterytray
4.Removethebatteryfromthebatterytray(Figure8).
5.Removethebatterytrayfromthebatteryplatform
(Figure8).
Note:Discardthebatterytray.
3

6.Looselymountthebracketonthetopoftheleftfender
tothefuel-tankbracketwith2bolts(3/8x3/4inch)
and2nuts(3/8inch)asshowninFigure9.
Figure9
1.Fuel-tankbracket2.Leftfender
7.Positionthebatteryontothebatteryplatform.
8.Looselymountthebatterytothebatteryplatformwith
thecarriagebolt,hold-down,washer,andnutthatyou
previouslyremoved(Figure10).
Figure10
9.Tightenthefasteners.
10.Connectthepositivebatterycabletothebattery,and
thenconnectthenegativebatterycabletothebattery.
11.Installthedrivewheels.
12.Tightenthelugnutsto102to115N-m(75to85ft-lb).
13.Removethejackstandsandlowerthemachine.
Note:Verifythatthetiresdonotrubonthefenders
whenyoudrivethemachine.
4