Torque TANK M1 User manual

TANK M1 OPTIONS ASSEMBLY GUIDE
PART #: 5750601-A

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
ITEM PART NUMBER DESCRIPTION QTY
1 57144PA PTD ASSY, UPPER MOUNT 1
2 57145PA PTD ASSY, LOWER MOUNT 1
3 2001101 WASHER, FLAT 3/8 SAE ST ZN 8
4 2031101 SCREW, 3/8" LAG X 2.5"L CLEAR ZINC 8
5 5617001 V-STRAP, TANK (OPTIONAL) 1
6 5560801 ASSY, TANK TOW ROPE 1
2
TABLE OF CONTENTS:
WALL MOUNT HANGER (OPTIONAL): PAGES 3-5 •
OPTIONAL ATTACHMENTS: PAGES 6-7 •
INSPECTION & LUBRICATION: PAGE 8 •
SHROUD REMOVAL: PAGE 9 •
CHAIN ADJUSTMENT: PAGE 10 •
SAFETY AND WARNING NOTICES: PAGE 11 •
TOOLS NEEDED FOR ASSEMBLY:
9/16" or 5/8" BOX WRENCH or •
9/16" or 5/8" SOCKET WITH RATCHET •
10MM BOX WRENCH or •
10MM SOCKET WITH RATCHET •
PHILLIPS HEAD SCREW DRIVER •

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
2
3
4
1-3/4"
1-3/4"
36"
6" (MIN)
FLOOR
WARNING:
THE LOWER MOUNT MUST BE ANCHORED TO THE WALL
USING FOUR WALL ANCHORS SUITABLE FOR THAT
PARTICULAR WALL CONSTRUCTION.
WARNING:
THE UPPER MOUNT MUST BE ANCHORED TO THE WALL
USING FOUR WALL ANCHORS SUITABLE FOR THAT
PARTICULAR WALL CONSTRUCTION.
XTWMH
WALL MOUNT HANGER (OPTIONAL)
NOTES:
The images above show the anchoring hardware used for attaching to
typical walls with wood studs spaced 16" on center. The anchors used
will depend on the wall construction. NOTE:
At least four anchoring
locations must be used in each part . The pull-out strength of the
anchoring bolts used must be greater than or equal to 200 lbs. (91 kg)
SECURELY tighten bolt connections in this step.
3

1
XTTM1
NOTE:
THESE LOOPS ARE FOR
ATTACHING RESISTANCE
BANDS AND INERTIA WAVE
MAX BAND RESISTANCE = 50 LBS.
NOTE:
THESE AREAS ARE FOR
ATTACHING BATTLE ROPES
RESISTANCE BANDS AND
INERTIA WAVE
MAX BAND RESISTANCE = 50 LBS.
2
XTWMH
WALL MOUNT HANGER (OPTIONAL)
4

2
LEFT PUSH HANDLE
RIGHT PUSH HANDLE
5
XTWMH
WALL MOUNT HANGER (OPTIONAL)

5
MAX WEIGHT PLATES:
2 - 45 LB BUMPER PLATES
3 - 45 LB GRIP PLATES
XTTM1
NOTE:
MAKE SURE PUSH/PULL BAR IS
ADJUSTED FORWARD BEFORE
ATTACHING V-STRAP
ATTACH V-STRAP TO PUSH/PULL
BAR WITH CARABINER (INCLUDED
WITH STRAP)
6
V-STRAP ATTACHMENT (OPTIONAL)
NOTE:
Weight plates are not included. Weight plates are only needed to
prevent skidding and lifting of the back wheels. Adding weight
does not affect the resistance.
To discover what accessories pair well with the TANK M1, visit our
web site at: www.torquefitness.com/collections/tank-accessories. or
by phone at 877-767-7835.

6
MAX WEIGHT PLATES:
2 - 45 LB BUMPER PLATES
3 - 45 LB GRIP PLATES
XTTM1
NOTE:
MAKE SURE PUSH/PULL BAR IS
ADJUSTED FORWARD BEFORE
ATTACHING TOW ROPE
ATTACH TOW ROPE TO
PUSH/PULL BAR WITH
CARABINER (INCLUDED)
7
TOW ROPE ATTACHMENT (OPTIONAL)
NOTE:
Weight plates are not included. Weight plates are only needed to
prevent skidding and lifting of the back wheels. Adding weight
does not affect the resistance.
To discover what accessories pair well with the TANK M1, visit our
web site at: www.torquefitness.com/collections/tank-accessories. or
by phone at 877-767-7835.

8
INSPECTION & LUBRICATION
INSPECTION:
ATTENTION:
PLEASE ENSURE THAT ALL TIRES ARE INFLATED
TO 30 PSI. FAILURE TO DO SO MAY RESULT IN
TANK VEERING DURING USE.
Once a month, check for loose bolts on frame and wheels. Tighten if
necessary.
Once a month, remove shroud as shown on PAGE 9 and check that
the chain and sprockets are clean, free of rust, dust and grime.
Make sure that the chain is properly lubricated.
If chain ever becomes loose, see PAGE 10 to adjust
chain.
Once a month, check tire pressure and inflate if needed.
LUBRICATION:
Once a month, the sprockets should be cleaned and the chain
should be lubricated.
RECOMMENDED LUBRICATION: Use a Dry lubrication for indoor
use, and wet lubrication for outdoor use. Most bicycle shops carry a
variety of different lubricants and can recommend a lubricant based
on the conditions where the TANK will be used.
#TorqueFitness #TorqueTANK
https://www.instagram.com/torquefitnessusa/
https://www.youtube.com/c/TorqueFitness
https://www.facebook.com/groups/thetankcommunity

USE A PHILLIPS SCREW
DRIVER TO LOOSEN AND
REMOVE 6 SCREWS AS
SHOWN. CAREFULLY LIFT
SHROUD OFF M1.
USE A PHILLIPS SCREW DRIVER TO
LOOSEN AND REMOVE 2 SCREWS
AND CAREFULLY REMOVE HANDLE.
BOTTOM VIEW
9
SHROUD REMOVAL - STEP 1 SHROUD REMOVAL - STEP 2

TO SET THE CORRECT CHAIN TENSION
FOLLOW THESE STEPS:
1) TIP M1 BACK SO THAT IT RESTS ON THE
REAR WHEELS AND PUSH HANDLES. AS
SHOWN.
2) LOOSEN ALL FOUR BOLTS ONE FULL
TURN EACH. (BOLT SHOULD BE LOOSE
ENOUGH TO ALLOW THE BRAKE MODULE
TO MOVE). ALLOW GRAVITY TO PULL THE
BRAKE MODULE DOWNWARD REMOVING
THE EXCESS SLACK.
3) SECURELY RE-TIGHTEN THE FOUR BOLTS.
10
CHAIN ADJUSTMENT

11
IMPORTANT SAFETY INSTRUCTIONS:
WARNING:
The safety of this product can be maintained only if it is examined regularly for damage
and wear. See inspection and lubrication section on page 8 for more details.
DO NOT overinflate tires! All tires should be inflated to 30 PSI. Check air pressure periodically. •
Keep children away from the TANK M1 during use. •
Keep all loose clothing, hair and shoelaces away from moving parts. •
DO NOT attempt to use the TANK M1 for any purposes other than that for which it was intended. •
Wear shoes with rubber or high-traction soles. High heels, dress shoes, sandals or bare feet are •
not suitable for use with the TANK M1.
DO NOT drop the front wheel down when turning the TANK M1 around. Carefully set the front •
wheel down - especially with weight plates on the weight horn.
DO NOT place more than 135 LBS. on the weight horn of the TANK M1. •
DO NOT drop the weight plates onto the TANK M1. Doing so, may result in damage to the TANK M1. •
DO NOT use the TANK M1 in wet or slippery conditions. •
DO NOT push the TANK M1 while any accessories are attached to the push/pull bar. •
DO NOT stand or ride on the TANK M1. •
DO NOT use the TANK M1 without the shroud. •
Torque Fitness
11201 Xeon Street NW Ste 101
Coon Rapids, MN USA 55448
www.torquefitness.com
Toll free: 1-877-TORQUE5 (1-866-664-9894)
or 763-754-7533 (8:30 am – 5:00 CST).
For sales: [email protected]
For service: [email protected]