Toshiba RAC-PD0811CRC User manual

USER MANUAL
RAC-PD0811CRC
RAC-PD1011CRC
RAC-PD1211CRC
RAC-PD1411CRC
RAC-PD1411CWC
RAC-PD1411HRC
Portable Type
Room Air Conditioner
Warning notices: Before using this product,
please read this manual carefully and keep
it for future reference.
The design and specications are subject to
change without prior notice for product
improvement. Consult with your dealer or
the manufacturer for details.
version B - 11 - 2017 - CANADA us.toshiba-lifestyle.com
U
SER MAN
U
A
A
L
L
Safety Precautions
Operating Instructions
Installation Instructions
Care and Cleaning
O
perating In
s
C
C
areandCle
a
Troubleshooting TipsTroubleshoo
t
Remote Control Operating
Instructions

Page 2 User Manual
Read This Manual
Inside you’ll find many helpful hints on how to use and maintain your air conditioner properly.
Just a little preventive care on your part can save you a great deal of time and money
over the life of your air conditioner. You’ll find many answers to common problems in the
troubleshooting tips - you should be able to fix most of them quickly before calling service.
These instructions may not cover every possible condition of use, so common sense and
attention to safety is required when installing, operating and maintaining this product.
User Manual
CAUTION
Safety Precautions ...................................................................................................... 3
Unit Specifi cations and Features .......................................................................... 5
Operating Instructions .............................................................................................. 6
Installation Instructions ......................................................................................... 11
Care and Cleaning ................................................................................................... 16
Troubleshooting Tips .............................................................................................. 17
Remote Control Operating Instructions .......................................................... 18
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The air conditioner is not intended for use by young children or people who cannot
operate the air conditioning independently without supervision.
• Young children should be supervised to ensure that they do not play with the air
conditioner.
• If the power cord needs to be replaced, please contact our consumer service and look
for an authorized technician.
• Electrical installation must be performed in accordance to national regulation standards
by qualied personnel only.

User Manual Page 3
SAFETY PRECAUTIONS
WARNING
WARNING: This symbol indicates the possibility of death or serious injury.
CAUTION: This symbol indicates the possibility of injury or damage to property.
To prevent injury to the user or other people and property damage, the following instructions must
be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The
seriousness is classied by the following indications.
Please read through these instructions before you start the installation process.
Improper installation can cause damage to the unit, your personal property, and also
poses a personal safety hazard.
• Installation must be performed according to the installation instructions. Improper
installation can cause water leakage, electrical shock, or re.
• Use only the included accessories and parts, and specied tools for the installation.
Using non-standard parts can cause water leakage, electrical shock, re, and injury or
property damage.
• Make sure that the outlet you are using is grounded and has the appropriate voltage.
The power cord is equipped with a three-prong grounding plug to protect against
shock. Voltage information can be found on the side of the unit, behind the grille.
• Install the unit on a at, sturdy surface. Failure to do so could result in damage or
excessive noise and vibration.
• The unit must be kept free from obstruction to ensure proper functioning and to
mitigate safety hazards.
• DO NOT modify the length of the power cord or use an extension cord to power the
unit. DO NOT share a single outlet with other electrical appliances. Improper power
supply can cause re or electrical shock.
• DO NOT install your air conditioner in a wet room such as a bathroom or laundry room.
Exposure to water can cause electrical components to short circuit.
• DO NOT install the unit in a location that may be exposed to combustible gas, as this
could cause re.
• The unit has wheels to facilitate moving. Do not attempt to roll the unit across thick
carpet or over objects, as this could cause the unit to tip over.
• DO NOT operate a unit that has been dropped or damaged.
• Only use the included accessories and specied parts for installation. Using
nonstandard parts can cause water leakage, electrical shock, re, and injury or
property damage.
Safety
Precautions

Page 4 User Manual
WARNING
• DO NOT allow children to play with the air conditioner. Children must be supervised
around the unit at all times.
• If the air conditioner is knocked over during use, turn o the unit and unplug it
from the main power supply immediately. Visually inspect the unit to ensure there
is no damage. If you suspect the unit has been damaged, contact a technician or
customer service for assistance.
• In a thunderstorm, the unit should be turned o to avoid damage to the machine
due to lightning.
CAUTION
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by
a person responsible for their safety.
• If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
• Prior to cleaning or other maintenance, the appliance must be disconnected from the
supply mains.
• Do not install the appliance in a location that may be exposed to combustible gas. If
combustible gas accumulates around the unit, it may cause re.
• Do not run the power cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or appliances.
Arrange cord away from traffic area and where it will not be tripped over.
• To reduce the risk of fire or electric shock, do not use this air conditioner with any
solid-state speed control device.
• The appliance shall be installed in accordance with national wiring regulations.
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the authorized installer for installation of this unit.
• When there are signicant dierences between features or operation implied by the
remote control illustration and the actual functions described in the USER MANUAL,
the descriptions in the USER MANUAL shall prevail.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.)
batteries.
Safety
Precautions

User Manual Page 5
Operating
Instructions
Preparation
control panel
handle
(both sides)
horizontal louver
blade
(automatic swing)
Caster power plug socket
power cord buckle
bottom tray
drain outlet
power cord outlet
drain outlet
(only for pump
heating mode)
upper air filter
(behind the grille)
upper air intake
air outlet
lower air filter
lower air intake
drain outlet
Panel
Front Rear
Design and Compliance Notes
Design Notice:
In order to ensure the optimal performance of our products, the design specications of the unit and
remote control are subject to change without prior notice.
Energy Rating Information:
The Energy Rating for this unit is based on an installation using an unextended exhaust duct without
adaptors A or B (as shown in the Installation section of this manual).
Unit Temperature Range:
Mode Temperature Range
Cool 17°C ~ 35°C (62°F ~ 95°F)
Dry 13°C ~ 35°C (55°F ~ 95°F)
Heat (heat pump mode) 5°C ~ 30°C (41°F ~ 86°F)
Heat (electrical heat mode) ≤ 30°C (86°F)
Exhaust Hose Installation:
The exhaust hose and adaptor must be installed or removed in accordance with the usage mode.
For COOL, HEAT (heat pump type) or AUTO mode, exhaust hose must be installed.
For FAN, DEHUMIDIFY or HEAT (electrical heat type) exhaust hose must be removed.

Page 6 User Manual
Control Panel Features
OPERATING INSTRUCTIONS
Operating
Instructions
Swing Button
Used to initiate the Auto Swing feature. When the
operation is ON, pressing the SWING button can
stop the louver at the desired angle.
Timer button
Used to initiate the AUTO ON start time and
AUTO OFF stop time program, in conjuction with
the Up ( ) and Down ( ) buttons. The timer
on or off light will illuminate depending on the
selected setting.
Fan button
Controls the fan speed. Press to control the fan
speed in four steps - LOW, MID, HIGH and AUTO.
The selected fan speed light (except AUTO) will
illuminate. When AUTO is selected, no lights will
illuminate.
Mode button
Selects the desired operating mode. Each time
you press the button, a mode is selected in a
sequence that goes from AUTO, COOL, DRY,
FAN and HEAT (cooling only models excluded).
The mode light illuminates and indicates the
selected mode.
Up ( ) and Down ( ) buttons
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F increments in
a range of 17°C/62°F to 30°C/86°F or the TIMER
setting in a range of 0 ~ 24hrs.
NOTE
Press the FAN button for 3 seconds to initiate
the ION feature, which helps remove pollen
and impurities from the air, and trap them in
the filter. Press it for 3 seconds again to turn
off the ION feature.
Power button
Power switch on/o.
Sleep (Eco)/Filter button
Used to initiate the SLEEP/ECO operation.
NOTE
The control is capable of displaying
temperature in degrees Fahrenheit or
degrees Celsius. To convert from one to
the other, press and hold the Up and Down
buttons at the same time for 3 seconds.
Timer
Button
Swing
Button
Power
Button
Sleep/Eco
Button
Fan
Button
Up ( ) and Down ( )
Buttons
Mode
Button
LED Display
D / S H / E
M / M L / F
ANGLE / OSCIL. TIMER / MIN. FAN / VENT SLEEP / VEILLE
F / V C / F
Wi-Fi Indicator Light
(Wi-Fi models only)

User Manual Page 7
WI-FI Function
(Available on Wi-Fi models only)
With the unit ON, press the VENT ANGLE/
SWING button for 3 seconds to initiate the
Wireless Connection mode. The LED display
will display “AP” to indicate the wireless access
point is available. Follow the instructions on the
Wi-Fi setup manual and the latest app version
available for your phone operating system. If
the connection is successful, the unit will exit
“AP” mode automatically and the Wi-Fi indicator
light will illuminate. If connection is unsuccessful
within 8 minutes, the unit exits “AP”mode and
returns to regular operation.
If the Wi-Fi function is ON and there is a need to
turn it o, press and hold the VENT ANGLE/SWING
button and DOWN (-) button simultaneously
for 3 seconds. The display will show“OFF” for
3 seconds and the Wi-Fi function will become
inactive. To turn it back on, press and hold the
VENT ANGLE/SWING button and UP (+) button
simultaneously for 3 seconds. The display will
show “ON” for 3 seconds. When you restart the
wireless functions, it will take a period of time to
connect to the network automatically. Always be
sure your wireless connection is working properly
and there is a valid internet connection for Wi-Fi
functionality to work.
NOTE
When one of the above malfunctions
occurs, turn off the unit and check for
any obstructions. Restart the Unit. If the
malfunction persists, turn off the unit
and unplug the power cord. Contact the
manufacturer or its service agents or a similar
qualified person for service.
Control Panel Features (cont.)
LED display
Shows the set temperature in °C (Degrees Celsius)
or °F (Degrees Fahrenheit) and the Auto-timer
settings. While on DRY and FAN modes, it shows
the room temperature.
Shows Error codes and protection code:
E1 - Room temperature sensor error.
E2 - Evaporator temperature sensor error.
E3 - Condenser temperature sensor error (select
models).
E4 - Display panel communication error.
P1 - Bottom tray is full - Connect the drain
hose and drain the collected water away.
If protection code repeats, call for service.
Timer
Button
Swing
Button
Power
Button
Sleep/Eco
Button
Fan
Button
Up ( ) and Down ( )
Buttons
Mode
Button
LED Display
Operating
Instructions
D / S H / E
M / M L / F
ANGLE / OSCIL. TIMER / MIN. FAN / VENT SLEEP / VEILLE
F / V C / F
Wi-Fi Indicator Light
(Wi-Fi models only)

Page 8 User Manual
Operating Instructions
COOL operation
• Press the“MODE” button until the“COOL”
indicator light comes on.
• Press the ADJUST buttons Up ( ) or
Down ( ) to select your desired room
temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F.
• Press the“FAN SPEED” button to choose the fan
speed.
HEAT operation
(available on HEAT models only)
• Press the“MODE” button until the “HEAT”
indicator light comes on.
• Press the ADJUST buttons Up ( ) or
Down ( ) to select your desired room
temperature. The temperature can be set
within a range of 17°C~30°C/62°F~86°F.
• Press the“FAN SPEED” button to choose the fan
speed. For some models, the fan speed cannot
be adjusted while in HEAT mode.
DRY operation
• Press the“MODE” button until the “DRY”
indicator light comes on.
• While in this mode, you cannot select a fan
speed or adjust the temperature. The fan
motor operates at LOW speed.
• Keep windows and doors closed for the best
dehumidifying eect.
• Do not connect the duct to a window.
AUTO operation
• When you set the air conditioner to AUTO mode,
it will automatically select cooling, heating
(cooling only models excluded), or fan only
operation depending on what temperature you
have selected and the current room temperature.
• The air conditioner will control room
temperature automatically according to the
temperature point set by you.
• Under AUTO mode, you cannot select the fan
speed.
FAN operation
• Press the“MODE” button until the ”FAN“
indicator light comes on.
• Press the“FAN SPEED” button to choose the fan
speed. The temperature cannot be adjusted.
• Do not connect the duct to a window.
TIMER operation
• When the unit is on, pressing the Timer button
will initiate the Auto-o stop program. The TIMER
OFF indicator light illuminates. Press the Up or
Down button to select the desired time. Press the
TIMER button again within 5 seconds. The Auto-
on start program is initiated and the TIMER ON
indicator light illuminates. Press the Up or Down
button to select the desired Auto-on start time.
• When the unit is o, press the Timer button to
initiate the Auto-on start program. Pressing it
again within ve seconds will initiate the Auto-
o stop program.
• Press or hold the Up or Down button to
change the Auto time by 0.5 hour increments,
up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the
time remaining until start.
• The system will automatically revert back to
display the previous temperature setting if there
is no operation within 5 seconds.
• Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timer program.
• Should a malfunction occur, the Auto Start/Stop
timed program will also be cancelled.
SLEEP/ECO operation
Pressing this button will increase (during cooling
operation) or decrease (during heating operation,
applicable models) 1°C/1°F after 30 minutes.
The temperature will again increase (cooling)
or decrease (heating) by another 1°C/1°F after
an additional 30 minutes. This new temperature
will be maintained for 7 hours before returning
to the originally selected temperature. This ends
the Sleep/Eco mode and the unit will continue to
operate as originally programmed.
NOTE
This feature is unavailabe in FAN or DRY mode.
Operating
Instructions

User Manual Page 9
Other Features
AUTO-RESTART
If the unit shuts o unexpectedly due to a power outage, it will restart with the previously set function
automatically when the power resumes.
WAIT 3 MINUTES BEFORE RESUMING OPERATION
After the unit has stopped, it cannot be restarted until 3 minutes time has elapsed. This is to protect the
unit. Operation will automatically resume after 3 minutes.
AIRFLOW DIRECTION ADJUSTMENT
The louver can be adjusted automatically. Adjust the airow direction automatically.
• When the Power is ON, the louver opens fully.
• Press the SWING button on the panel or remote controller to initiate the Auto Swing feature. The
louver willl swing up and down automatically.
• Please do not adjust the louver manually.
WATER DRAINAGE
• During dehumidifying modes, remove the upper drain plug
from the back of the unit and install the drain connector (5/8”
universal female mender) with 3/4” hose (locally purchased).
For models without drain connector, just attach the drain hose
to the hole. Place the open end of the hose directly over the
drain area in your basement oor.
Remove the
upper drain plug
Continuous
drain hose
¥
• During heating mode, remove the lower drain plug from the
back of the unit and install the drain connector (5/8” universal
female mender) with 3/4” hose (locally purchased). For models
without drain connector, just attach the drain hose to the
hole. Place the open end of the hose adaptor directly over the
drain area in your basement oor.
Units with
Pump Only
¥
drain hose
adaptor
Continuous
drain hose
Remove
the lower
drain plug
Operating
Instructions

Page 10 User Manual
NOTE
¥
delivery lift <1.8m
drain
hose
adaptor
drain
hose
adaptor X
Make sure the hose is secure so there are no leaks. Direct the hose toward the drain, making sure that
there are no kinks that will impede water ow. Place the end of the hose into the drain and make sure
the end of the hose is directed downward to let the water ow smoothly. (See Figs with ).
Installation not recommended. (See Figs with X). When the continuous drain hose is not used,
ensure that the corresponding drain plug and knob are installed rmly to prevent leakage.
WATER DRAINAGE cont.
• When the water level of the bottom tray reaches a
predetermined level, the unit beeps 8 times. The digital display
shows “P1.” At this time the air conditioning/dehumidication
process will immediately stop. However, the fan motor will
continue to operate (this is normal). Carefully move the unit
to a drain location, remove the bottom drain plug and let the
water drain away. Reinstall the bottom drain plug and restart
the machine until the “P1” symbol disappears. If the error
repeats, call for service.
NOTE
Be sure to reinstall the bottom drain plug rmly to prevent
leakage before using the unit.
Units with
Pump Only
Operating
Instructions

User Manual Page 11
INSTALLATION INSTRUCTIONS
Choosing the Right Location
Recommended Installation
30 cm
12 inch
30 cm
12 inch
Your installation location should meet the following
requirements:
• Make sure that you install your unit on an even
surface to minimize noise and vibration.
• The unit must be installed near a grounded plug, and
the Collection Tray Drain (found on the back of the
unit) must be accessible.
• The unit should be located at least 30 cm (12”) from
the nearest wall to ensure proper air conditioning.
• DO NOT cover the Intakes, Outlets or Remote Signal
Receptor of the unit, as this could cause damage to
the unit.
NOTE About Fluorinated Gasses
• This air-conditioning unit is a hermetically sealed unit that contains uorinated gasses. For specic
information on the type of gas and the amount, please refer to the relevant label on the unit itself.
• Service, maintenance or repair of this unit must be performed by a certied technician.
• Product recycling must be done according to local regulations.
NOTE
All images in the manual are illustrative. Your unit may
be slightly different.
50cm
19.7inch
Installation
Instructions

Page 12 User Manual
Accessories
Your Window Installation Kit ts windows 67.5-123 cm (26.5”-48”) and can be shortened for smaller windows.
Part Description
Unit adaptor
Window slider adaptor
Window slider A
Window slider B
Exhaust hose
Bolt
Foam seal A (adhesive)
Foam seal B (adhesive)
Foam seal C (Non-adhesive)
Security bracket and 2 screws
Drain hose
Drain hose adaptor
(For heat pump mode only)
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pc
2 pc
1 set
1 set
Quantity
Remote controller and battery
(For remote control models only)
ON/OFF
TEMP
SHORT
C UT
TIMER ON
TIMER OFF
MODE
FAN
SLEEP SWING LED
Tools Needed
• Medium Phillips screwdriver
• Tape measure or ruler
• Knife or scissors
• Saw (optional, to shorten window adaptor for narrow windows).
Installation
Instructions

User Manual Page 13
Window Installation Kit
Step One: Preparing the exhaust hose
assembly
Press the exhaust hose into the window slider
adaptor and unit adaptor, clamp automatically
by elastic buckles of the adaptors.
Step Two: Install the exhaust hose
assembly to the unit
Insert unit adaptor of the Exhaust hose assembly
into the lower groove of the air outlet of the
unit with the hook of the adaptor aligned with
the hole seat of the air outlet and slide down
the Exhaust hose assembly along the direction
indicated by the arrow for installation.
Step Three: Preparing the adjustable
window slider
1. Depending on the size of your window,
adjust the size of the window slider.
2. If the length of the window requires two
window sliders, use the bolt to fasten the
window sliders once they are adjusted to
the proper length.
Unit
adaptor
Window slider
adaptor
Exhaust hose Exhaust hose
assembly
Hook Hole Seat
Lower
groove
Adaptor Make sure the adaptor
is inserted into the
lower groove of the
air outlet.
Hung Window Sliding Window
Windows Type
Window slider A Window slider B
Bolt
Window
slider A
Window
slider A
Installation
Instructions

Page 14 User Manual
Type 1: Hung window installation
1. Cut the adhesive foam seal A and B strips to the proper lengths,
and attach them to the window sash and frame as shown.
2. Insert the window slider assembly into the window opening.
3. Cut the non-adhesive foam seal C strip to match the width of
the window. Insert the seal between the glass and the window
frame to prevent air and insects from getting into the room.
4. If desired, install the security bracket with 2 screws as shown.
5. Insert the window slider adaptor into the hole of the window
slider.
NOTE
Once the Exhaust Hose assembly and Adjustable Window Slider are prepared, choose from one of
the following two installation methods.
Foam seal B
(Adhesive type-shorter)
Foam
seal A
(Adhesive
type)
Window
slider A
Window
slider B
(if required)
Foam seal C
(Non-adhesive type)
Security Bracket
2 Screws
Installation
Instructions

User Manual Page 15
Type 2: Sliding window installation
1. Cut the adhesive foam seal A and B strips to the proper lengths,
and attach them to the window sash and frame as shown.
2. Insert the window slider assembly into the window opening.
3. Cut the non-adhesive foam seal C strip to match the window
height. Insert the foam seal between the glass and the window
frame to prevent air and insects from getting into the room.
4. If desired, install the security bracket with 2 screws as shown.
5. Insert the window slider adaptor into the hole of the window
slider.
Window slider A
Window slider B
(if required)
Foam seal B
(Adhesive
type-shorter)
Foam seal A
(Adhesive
type)
Foam seal C
(Non-adhesive type)
2 Screws
Security
Bracket
NOTE
To ensure proper functioning, DO NOT overextend or bend the hose. Make sure that there is
no obstacle around the air outlet of the exhaust hose (in the range of 500mm) in order for the
exhaust system to work properly. All illustrations in this manual are for explanation purposes
only. Your air conditioner may be slightly different. The actual shape shall prevail.
Installation
Instructions

Page 16 User Manual
Air Filter Cleaning
Unit Cleaning
Store the Unit When Not in Use
Safety Precautions
CARE AND CLEANING
• Always unplug the unit before cleaning or servicing.
• DO NOT use ammable liquids or chemicals to clean the unit.
• DO NOT wash the unit under running water. Doing so causes electrical danger.
• DO NOT operate the machine if the power supply was damaged during cleaning. A damaged
power cord must be replaced with a new cord from the manufacturer.
Clean the unit using a damp, lint-free cloth and mild detergent. Dry the unit with a dry, lint-free cloth.
• Drain the unit’s water collection tray according to the instructions in the following section.
• Run the unit on FAN mode for 12 hours in a warm room to dry it and prevent mold.
• Turn o the unit and unplug it.
• Clean the air filter according to the instructions in the previous section. Reinstall the clean, dry
filter before storing.
• Remove the batteries from the remote control.
Remove the
air filter
Upper filter
(take out)
Remove the
screw, then
take the lower
filter out.
NOTE
Be sure to store the unit in a cool, dark place. Exposure to direct sunlight or extreme heat can
shorten the lifespan of the unit.
Maintenance Tips
• Be sure to clean the air filter every 2 weeks
for optimal performance.
• The water collection tray should be drained
immediately after P1 error occurs, and before
storage to prevent mold.
• In households with animals, you will have to
periodically wipe down the grill to prevent
blocked airow due to animal hair.
CAUTION
DO NOT operate the unit without lter because
dirt and lint will clog it and reduce performance.
Care and Cleaning

User Manual Page 17
Malfunction Diagnosis
TROUBLESHOOTING TIPS
Please check the machine according to the following table before calling for service:
Problem Possible Cause Troubleshooting
Unit does not turn
on when pressing
ON/OFF button
P1 Error Code. The water collection tray is full.
Turn o the unit, drain the water from
the water collection tray and restart
the unit.
In COOL mode: room temperature is
lower than the set temperature.
Reset the temperature.
Unit does not cool
well
The air lter is blocked with dust or
animal hair.
Turn o the unit and clean the lter
according to instructions.
Exhaust hose is not connected or is
blocked.
Turn o the unit, disconnect the hose,
check for blockage and reconnect the
hose.
The unit is low on refrigerant. Call a service technician to inspect the
unit and top o refrigerant.
Temperature setting is too high. Decrease the set temperature.
The windows and doors in the room are
open.
Make sure all windows and doors
are closed.
The room area is too large. Double-check the cooling area.
There are heat sources inside the room. Remove the heat sources if possible.
The unit is noisy
and vibrates too
much
The oor is not level. Place the unit on a at, level surface.
The air lter is blocked with dust or
animal hair.
Turn o the unit and clean the lter
according to instructions.
The unit makes a
gurgling sound
This sound is caused by the ow of
refrigerant inside the unit.
This is normal.
Unit stops
frequently
The exhaust hose is blocked, extended
or otherwise restricted.
Remove the exhaust hose to see if the
unit continues to operate. If yes, shorten
the extension, reduce the number of
bends or eliminate restriction.
NOTE
Do not add extension to the exhaust hose(s)!
Troubleshooting
Tips

Page 18 User Manual
Remote Control Specifi cations
Function Buttons
REMOTE CONTROL OPERATING INSTRUCTIONS
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the Operating Instructions section of this manual.
Model RG57H(B)/BGE
Rated voltage 3.0V (Dry batteries R03/LR03x2)
Signal receiving range 8 m (approx. 26 ft.)
Environment -5°C ~ 60°C (23°F ~ 140°F)
SHORT CUT
Sets and activates your favorite pre-settings.
ON/OFF
Turns the unit on or off.
S
TEMP
Increases temperature in 1°C (1°F) increments.
Max. temperature is 30°C (86°F).
TIMER ON
Sets timer to turn unit on (see How to Use
Basic Functions for instructions)
TIMER OFF
Sets timer to turn unit off (see How to Use
Basic Functions for instructions)
LED
Turns indoor unit's LED display on and off.
If you are sensitive to light while sleeping,
you can press the LED button to turn off
the LED display on the unit. Press the
button again to turn it back on.
SWING
Starts and stops
louver movement.
SLEEP
Saves energy during
sleeping hours.
T
TEMP
Decreases temperature in 1°C (1°F) increments.
Min. temperature is 17°C (62°F).
NOTE: Pressing and holding and buttons
together for 3 seconds will alternate the
temperature display between the °C & °F scale.
TS
FAN SPEED
Selects fan speeds in the
following order:
AUTO LOW MED HIGH
JJJ
MODE
Scrolls through operation modes
as follows:
AUTO COOL DRY HEAT FAN
JJJJ
NOTE:
Please do not select HEAT mode
if the machine you purchased is
cool-only type. Heat mode is not
supported by cool-only models.
NOTE
Model no. RG57H1(B)/BG(C)E-M does not include med fan speed.
Operating
Instructions
(With Remote)
PRESET
MARCHE/
ON
ARRÊTER/
OFF

User Manual Page 19
Handling the Remote Control
NOT SURE WHAT A FUNCTION DOES?
Refer to the Operating Instructions section of this manual for a detailed description of how to use your
air conditioner.
SPECIAL NOTE
Button designs on your unit may differ slightly from the example shown.
If the unit does not have a particular function, pressing that function’s button on the remote
control will have no effect.
When there are significant differences between features or operation implied by the remote
control illustration and the actual functions described in the USER’S MANUAL, the descriptions in
the USER’S MANUAL shall prevail.
INSERTING AND REPLACING BATTERIES
Your air conditioning unit comes with two AAA batteries. Insert the
batteries in the remote control before use.
1. Slide the back cover of the remote control downward, exposing
the battery compartment.
2. Insert the batteries, paying attention to align the (+) and (-) ends
of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to
local laws for proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
• The remote control must be used within 8 meters / 26 feet of
the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with
the infrared signal receiver.
• Remove batteries if the remote will not be used more than 2
months.
BATTERY NOTES
For optimum product performance:
• Do not mix old and new batteries, or batteries of dierent types.
• Do not leave batteries in the remote control if you don’t plan
on using the device for more than 2 months.
Operating
Instructions
(With Remote)

Page 20 User Manual
AUTO
COOL
DRY
HEAT
FAN
Transmission Indicator
Lights up when remote sends signal to unit
MODE display
Displays the current
mode, including:
TIMER ON display
Displays when
TIMER ON is set
TIMER OFF display
Displays when
TIMER OFF is set
ECO display
Not available on this unit
Battery display
Low battery detection
Not available on this unit
SLEEP display
Displays when SLEEP
function is activated
SILENT display
Not available on this unit
FAN SPEED display
Displays selected FAN SPEED:
HIGH
MED
LOW
This display is blank when
set to AUTO speed.
Temperature/Timer display
Displays the set temperature by default, or timer setting
when using TIMER ON/OFF functions:
- Temperature range: 17-30°C (62°F-86°F)
- Timer setting range: 0-24 hours
This display is blank when operating in FAN mode.
FOLLOW ME display
Not available on this unit
ON/OFF display
Appears when the unit is turned on and disappears when it is turned off
Remote LED Screen Indicators
Operating
Instructions
(With Remote)