Toshiba RBM-BT14E User manual

INSTALLATION MANUAL
Air Conditioner (Multi Type)
Outdoor unit connection piping kit (For R410A)
Model name: RBM-BT14E, RBM-BT24E
EH78207101-1
Please read and follow the "PRECAUTIONS FOR SAFETY" in the installation manual for the air conditioner.
• Make sure all the parts listed in the table are included in the package.
• Read the installation manual for the air conditioner regarding the selection of the size and material of the refrigerant pipes.
• Ask an authorized dealer or qualified installation professional to install this product.
• Installation work must be carried out by following this installation manual and using exclusive tools and pipes for the refrigerant R410A.
1English
Parts Table
NOTE
1 ( ): indicates outer diameter.
2 For the sockets, the side with a notch is the one to connect a pipe. ( , , : without notch)
Unit: mm
Gas side joint Liquid side joint Balance pipe joint
RBM-
BT14E
Socket
No. Specifications No. Specifications No. Specifications No. Specifications Specifications
Ø34.9 × (Ø31.8) 1 pc (Ø28.6)×Ø22.2 2 pcs Ø15.9×(Ø19.1) 1 pc (Ø19.1)×Ø12.7 2 pcs
Ø28.6 × (Ø31.8) 1 pc
Joint Joint 1 pc L-pipe (Ø25.4)×Ø28.6 1 pc T-joint 3-Ø19.1 1 pc T-joint 3-Ø9.5 1 pc
Heat
insulator Heat insulator for joint 1 pc Heat insulator for L-pipe 1 pc Locally procured Locally procured
RBM-
BT24E
Socket
No. Specifications No. Specifications No. Specifications No. Specifications Specifications
Ø41.3×(Ø38.1) 1 pc (Ø38.1)×Ø41.3 1 pc Ø19.1×(Ø22.2) 1 pc (Ø22.2)×Ø19.1 1 pc
Ø34.9×(Ø38.1) 1 pc (Ø38.1)×Ø34.9 1 pc (Ø22.2)×Ø15.9 2 pcs
(Ø38.1)×Ø28.6 1 pc (Ø22.2)×Ø12.7 1 pc
(Ø38.1)×Ø22.2 1 pc
(Ø28.6)×Ø22.2 1 pc
Joint Joint 1 pc L-pipe (Ø31.8)×Ø28.6 1 pc T-joint 3-Ø22.2 1 pc T-joint 3-Ø9.5 1 pc
Heat
insulator Heat insulator for joint 1 pc Heat insulator for L-pipe 1 pc Locally procured Locally procured
59 61 62
Diameter of the
connecting pipe
External
diameter of
socket
Socket Notch
Ø28.6
Ø22.2
L-pipe
27
(Ø31.8)
59
(Ø28.6)
Ø28.6
(Ø28.6)
Ø22.2
(Ø31.8)
Ø34.9 Ø31.8 Ø28.6
(Brazed locally) (Ø25.4)
43
43
(Ø19.1)
Ø12.7
Ø12.7
Ø15.9
(Ø19.1) 3-Ø19.1
(Ø19.1)
13 10
10
3-Ø9.5
59 43 13 10
27
(Ø38.1)
L-pipe
Ø22.2
(Ø28.6)
Ø38.1
Ø41.3
Ø28.6
73
Ø34.9
(Ø38.1)
Ø38.1
(Brazed locally) (Ø28.6)
(Ø38.1)
Ø41.3 Ø34.9 Ø28.6 Ø22.2
71
6162
43
61 62
(Ø38.1) (Ø38.1) (Ø38.1) Ø19.1
Ø15.9
Ø19.1 3-Ø22.2
(Ø22.2)
18
14
Ø12.7
(Ø22.2)
(Ø22.2) (Ø22.2)(Ø22.2)
18
85
14
Ø15.9
3-Ø9.5
62 62 18 18
61 61 14
71 85
73
43
Installation and connection
Select the model and the number of outdoor unit connection piping kits that you need based on the sales catalog, design engineering, and the
data book and installation manual of outdoor unit.
CAUTION
• When brazing the refrigerant pipes, be sure to put the nitrogen first to prevent from oxidizing the inner pipe. If not, the oxidization scale
brings the refrigerant cycle clogging and result in malfunction.
• Use clean new pipes for the refrigerant pipes, and do not let water, moisture or dust get into the pipes during installation.
1Installation mode
<Gas joint>
Install them horizontally with a maximum gradient of ±15° for even distribution. (Do not install them perpendicularly or upright.)
(Figure 4, Figure 5, Figure 6, Figure 7)
<Liquid/balance pipe joint>
No restrictions on the installation orientation by the direction of refrigerant flow. However, on the liquid joint the installation cannot have the
refrigerant from the main pipe flow directly into the header unit. (Figure 2).
▼Liquid pipes
Figure 1 Figure 2
▼Gas pipes
Figure 3 <Gas joint reverse orientation installation>
Figure 4
<Gas joint upright orientation installation>
Figure 5
<Vertical installation>
Figure 6
<Vertical installation>
Figure 7
A
B
Horizontal line
Within ±15°
A view
Horizontal line
B view
Within ±15°
A
Horizontal line
Horizontal line
A view
A view
Header unit A Follower unit B Follower unit C
Main pipe
To indoor unit Liquid joint Extension valve installation site
(For planned system expansion)
Good
Header unit A Follower unit B Follower unit C
To indoor unit
Main pipe
Not
Good
Header unit A Follower unit B Follower unit C
Main pipe
Gas joint
To indoor unit Extension valve installation site
(For planned system expansion)
Good
Header unit A Follower unit B Follower unit C
Main pipe
Gas joint
To indoor unit
Not
Good
Gas joint
Header unit A Follower unit B
Main pipe
Gas joint
To indoor unit
A view
Gas joint
A
Not
Good
Unit
Vartical line
Header unit A
Gas joint
Not
Good
Header unit A
Gas joint
Not
Good
+EH78207101_01EN.fm Page 1 Wednesday, September 22, 2010 3:42 PM

1English
2Connection Method
<Gas joint>
Determine the installation orientation of the L-pipe according to the piping connections from the outdoor unit, and select a socket that matches
the diameter of the locally procured pipes.
<Liquid joint>
Select a socket to match the diameter of the locally procured piping and install it.
<Balance pipe joint>
For 2 outdoor units system, connect directly between the header unit and the follower unit.
3Example of pipe connections
Install and connect the piping between the outdoor units as shown in the diagram below.
NOTE
There are no specific requirements on the length of the straight pipe before the joint for either the gas or liquid sides.
<For connections to the front>
To outdoor unit
Locally procured piping
Locally procured piping
To main pipe or to
other joint Inlet
Outlet (2)
Outlet (1)
Socket (Provided)
Socket (Provided)
L-pipe (Provided)
Locally procured piping
To outdoor unit or to
other joint
Gas joint (Provided)
Socket (Provided) Brazed locally
NOTE
• Select the socket (No.in ) fitting to the pipe diameter
connected to the outdoor unit.
• After cutting the pipe, be sure to remove the burrs and
polish the end surface. When some squash or
deformation, etc. occurs, improve the pipe insertion
condition by using the flare tool.
• Confirm whether no dust, water, foreign matters, etc
exists on the gas joint, the liquid joint, the balance pipe
joint and the socket to be inserted.
Locally procured piping
Socket (Provided)
To main pipe or to
liquid joint Socket (Provided)
Liquid joint (Provided)
To outdoor unit
To outdoor unit or
to other joint
Locally procured piping
Socket (Provided)
Locally procured piping
Balance pipe joint (provided)
Locally procured piping
To outdoor unit or
to other joint
To outdoor unit
or to other joint
Locally procured piping
To outdoor unit Locally procured piping
A
Outdoor unit
connection piping kit
L-pipe
Balance pipe
Gas pipe Locally procured
piping
Header unit A
Liquid pipe
Follower unit B Follower unit C
To indoor units
Balance
pipe joint
Liquid joint
Gas joint
A view
Horizontal line
Gas joint
<For connections to the bottom>
Remove the knock-out hole from the bottom of the outdoor units.
(Refer to the installation manual of the outdoor unit.)
4Heat insulating for pipes
• Insulate the joints of the liquid pipe, gas pipe, and balance pipe individually.
• Insulator for the liquid joint and the balance pipe joint are not provided. Please procure it locally.
<Gas pipe>
• Use heat insulators with heat resistance of 120 °C or more for the gas pipe.
• In order to prevent dripping condensation, do not leave any gap between heat insulator for branching joint (included in package) and heat
insulator for pipe (locally procured). And then, wrap the seam with heat insulator with thickness of 10 mm or more (locally procured).
How to apply the insulation to the gas joint
<Liquid /balance pipe>
• To heat insulate the T-joints, use a commercially available joint cover (for T-shape) that is with 10 mm or more thickness, or one applied
with machining as shown in the figure.
• Seal the T-joints completely without any gap to prevent condensation and dripping water.
A
Locally procured
piping
Gas joint
Balance
pipe
L-pipe
500 mm or more
Header unit A
Liquid pipe
Follower unit B Follower unit C
To indoor units
Gas pipe
Liquid joint
Balance
pipe
joint
A view
Horizontal line
Gas
joint
Heat insulator
(Locally procured)
Heat insulator
(Provided)
Joint
No gap
Taping (Locally procured)
Taping (Locally procured)
Heat insulator
(Locally procured)
H
ea
t
i
nsu
l
a
t
or
(Provided)
Locally procured
piping heat insulator
(with thickness of 10
mm or more)
No gap
Locally procured
piping insulator
(with thickness of
10 mm or more)
150
Seal with vinyl tape
90° cutout
Insulated pipe 90°
Seal the seams with
urethane foam
Insulated pipe
Heat insulator
Diameter of
insulated pipe joint
Cut at 90°
100mmor
more
ØD
ØD
+EH78207101_01EN.fm Page 2 Wednesday, September 22, 2010 3:42 PM