Toshiba GD 1080 How to use

SERVICE HANDBOOK
FACSIMILE (FOR DP4500/3500)
GD1080/1090
Click the Navigation Pane button to open the overview area and
display bookmarks and thumbnails palettes.
Click the Bookmarks to open the Contents and display Bookmarks
created for the document. Click a bookmark's name to go to the
Page marked by that bookmark.
Click the Thumbnails to open the overview area and display
thumbnail images of each document page. Click a thumbnail to go
to the Page marked by that thumbnail.
Copyright TOSHIBA TEC CORPORATION 2001
ALL RIGHTS RESERVED

GENERAL PRECAUTIONS REGARDINGTHE INSTALLATION
AND SERVICE FOR DP4500/3500 AND GD1080/1090
The installation and service should be done by a qualified service technician.
1. Transportation/Installation
• When transporting/installing the copier, employ two persons and be sure to use the positions as
indicatedbelow.
Thecopierisquiteheavyandweighsapproximately73kg(161lb),thereforepayfullattentionwhen
handlingit.
• Be sure to use a dedicated outlet with AC 115V or 120V/15A (220V, 230V, 240V/10A) or more for
itspower source.
• The copier must be grounded for safety.
Never ground it to a gas pipe or a water pipe.
• Select a suitable place for installation.
Avoid excessive heat, high humidity, dust, vibration and direct sunlight.
• Also provide proper ventilation as the copier emits a slight amount of ozone.
• To insure adequate working space for the copying operation, keep a minimum clearance of
80 cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.
2. Service of Machines
• Basically, be sure to turn the main switch off and unplug the power cord during service.
• Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the
dampheaterandtheirperiphery.
• Be sure not to touch high-voltage sections such as the chargers, high-voltage transformer, IH
control circuit, exposure lamp control inverter, inverter for the LCD backlight and power supply
unit.Especially, the board of these components should not be touched since the electirc charge
may remain in the condensers, etc.on them even after the power is turned OFF.
• Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc.
• Becarefulwhen removing the coverssince there mightbethe parts with very sharp edges under-
neath.
• When servicing the machines with the main switch turned on, be sure not to touch live sections
androtating/operatingsections.Avoid exposuretolaser radiation.
• Use suitable measuring instruments and tools.
• Avoid exposuretolaserradiationduring servicing.
−Avoid direct exposure to the beam.
−Do not insert tools, parts, etc.that are reflective into the path of the laser beam.
−Remove all watches, rings, bracelets, etc.that are reflective.

3. Main Service Parts for Safety
• Thebreaker,door switch,fuse, thermostat,thermofuse,thermistor, etc.are particularlyimportant
for safety.Be sure to handle/install them properly.
4. Cautionary Labels
• During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the
power cord during service”,“Hotarea”,“Laser warninglabel”etc.to seeif there is anydirt on their
surface and whether they are properly stuck to the copier.
5. Disposition of Consumable Parts/Packing Materials
• Regardingtherecoveryanddisposal of the copier,supplies,consumableparts and packingmate-
rials, it is recommended to follow the relevant local regulations or rules.
6. When parts are disassembled, reassembly is basically the reverse of disassembly unless
otherwise noted in this manual or other related documents. Be careful not to reassemble
small parts such as screws,washers,pins,E-rings,star washers in the wrong places.
7. Basically,the machine should not be operated with any parts removed or disassembled.
8. Precautions Against Static Electricity
• ThePCboard mustbe stored in an anti-electrostatic bagandhandledcarefully using a wristband,
because the ICs on it may become damaged due to static electricity.
Caution: Before using the wristband,pull out the power cord plug of the copier and make
sure that there are no uninsulated charged objects in the vicinity.
Caution: Dispose of used batteriesandRAM-ICs including lithium batteries
according to the manufacturer’s instructions.
Attention: Se débarrasser de batteries et RAM-ICs usés y compris les batteries en
lithium selon les instructions du fabricant.
Vorsicht : Entsorgung des gebrauchten BatterienundRAM-ICs (inklusive
der Lithium-Batterie) nach Angaben des Herstellers.

1. ERROR CODES
2. SELF-DIAGNOSIS MODE
3. TROUBLESHOOTING
4. PRECAUTIONS FOR
INSTALLATION OF FAX UNIT
5. UPDATING THE FIRMWARE

IOctober 2000 © TOSHIBA TECGD1080/1090 CONTENTS
CONTENTS
1. ERRORCODES ......................................................................................................................... 1-1
1.1 Transmission/ReceptionJournalandErrorCodeList.............................................................. 1-1
1.2 ErrorMessages ..................................................................................................................... 1-4
2. SELF-DIAGNOSIS MODE .......................................................................................................... 2-1
2.1 Test Mode(03) ....................................................................................................................... 2-2
2.2 AdjustmentMode(05)............................................................................................................ 2-4
2.3 SettingMode(08) .................................................................................................................. 2-6
2.4 FunctionMode(13) ................................................................................................................ 2-7
2.5 FaxClearing Mode (1*)........................................................................................................... 2-30
2.6 SettingtheRDC Password..................................................................................................... 2-33
2.7 AutomaticOrderfor Supplies ................................................................................................. 2-34
3. TROUBLESHOOTING ................................................................................................................ 3-1
3.1 FlowChartfor RecommendedTelephoneScreening............................................................... 3-2
3.2 Error Analysis Flow................................................................................................................ 3-5
3.3 ListsRequiredWhen ProblemHas OccurredintheField ....................................................... 3-6
3.4 OtherInformationRequired for Error Analysis ........................................................................ 3-11
4. PRECAUTIONS FOR INSTALLATION OF FAX UNIT ................................................................. 4-1
4.1 Installation of Fax Unit ........................................................................................................... 4-1
4.2 Country/RegionCode ............................................................................................................. 4-2
5. UPDATINGTHE FIRMWARE ...................................................................................................... 5-1

October 2000 © TOSHIBA TEC 1 - 1 GD1080/1090 ERROR CODES
1. ERROR CODES
1.1 Transmission/Reception Journal and Error Code List
The transmission journal is shown below. The error code list and status code list are available in the
following pages.The reception journal is output in the same form.
TRANSMISSION JOURNAL TIME : MM-DD-YY TIME
TEL NO.1 : XXXXXXXXX
TEL NO.2 : XXXXXXXXX
NAME : X X X X X X X
NO. FILE NO. DATE TIME DURATION PGS TO DEPT MODE STATUS
001 001 12.01 09:00 00:55 2 ABCD G3 xxx OK xx
Statuscode
Errorcode

GD1080/1090 ERROR CODES 1 - 2 October 2000 © TOSHIBA TEC
Normal
Paper jam
Original jam
Door is open
Power failure
(Reset)
Polling error
Memory full
Line is busy
Security mismatch
in relay or mail box
transmission
Initial signal not
detected
Terminal constants
not compatible
Reception of DCN
(Phase B)
DCS/DTCnot detected
Training error
CFR not detected
Image signal
carrier not detected
High speed signal
not detected
Image signal carrier
disconnected
1st EOL not detected
EOL not detected
Post message not
detected
Reception of DCN
Poor image quality
Image memory error
00
11
12
13
20
30
33
42
50
53
B0
B1
B2
B3
B4
B5
C0
C1
C2
C3
C4
D0
D1
D2
E0
Remove the jamming paper.
Remove the jamming document and retransmit it.
Close the doors securely and retransmit the document.
A power failure occurred during transmission or reception, and the transmis-
sion/reception data were lost. Attempt the transmission/reception again.
Communication was stopped by the FC key.
Polling was not performed because the polling document was not found.Check
the polling document on the other side and attempt the polling again.
The memory became full during reception. (The pages normally received are
printed out.)Checkthe remainingmemoryspace andattempt thereception again.
Transmission is not made because the line is busy. Attempt the transmission
again.As the number of the redialings are increased, the possibility for success-
ful transmission is increased.
Check your security code and system password of the other side as well as your
own.
NSF/DIS cannot be detected. Check the receiver and attempt the transmission
again.
DIS/NSF that cannot be handled by the sender was received.The receiver re-
ceived NSS/DCS other than those declared by DIS/NSF. Check the transmis-
sion/reception functions, and attempt the communication again.
DCN was received in the phase B.
DCS/DTC cannot be detected.
The sender performed fall-back but the transmission was not made. After the
reception of FTT, the receiver received a time-out or DCN. Adjust the transmitter
attenuator, link equalizer, etc. and retry the communication.
A training signal was sent out but CFR cannot be detected.Adjust the transmitter
attenuator, link equalizer, etc. and retry the transmission.
Acarrierwasnot detectedon the receivingside.Adjustthe transmitterattenuator,
link equalizer, etc. and retry the transmission.
High-speed signals were not detected on the receiving side.Adjust the transmit-
ter attenuator, link equalizer, etc. and retry the transmission.
Carrier disconnection was detected after the image signal was detected.
1st EOL was not detected after the high-speed signal was detected.
EOL cannot be detected on the receiving side.Or decoding is not possible with MMR.
A post message cannot be detected.Retry the communication.MCF, RTP, RTN,
PIN and PIP cannot be detected on the sending side.MPS, EOM and EOP can-
not be detected on the receiving side.
DCN was received.
Quality of the received image is poor. Retry the transmission.
Hardware is defective.
[A] Error code list
If an error has occurred during communication, an error code is indicated below “STATUS” on the
transmission/reception journal.
Take the appropriate action referring to the following list.
Error code Content Situation and corrective action

October 2000 © TOSHIBA TEC 1 - 3 GD1080/1090 ERROR CODES
[B] Status code list
[Example of the indication of a status code]
522
MMR (encoding system)
8 x 15.4 (resolution)
14400 (transmission speed)
Mode Transmission speed Resolution Encoding system
0 2400 8 x 3.85 MH
1 4800 8 x 7.7 MR
2 7200 8 x 15.4 MMR
3 9600 JBIG
4 12000 16 x 15.4
5 14400
6 16800
7 19200
8 21600 300 x 300
9 24000
A 26400
B 28800
C 31200
D 33600
E
F
Error code Content Situation and corrective action
E8
F0
F1
HDD error
Software trouble
Hardware noise
Hardware is defective.
Software is defective.
Hardware is defective.

GD1080/1090 ERROR CODES 1 - 4 October 2000 © TOSHIBA TEC
Remarks
Message displayed only
during the memory input.
It is not displayed during
the memory reception
Job information is stored
in the memory when the
final retry is finished.
1.2 Error Messages
Error messages are not displayed for the background jobs (memory transmission and memory recep-
tion). See the reception/transmission report for the details of the errors.
If an original jam during the direct transmission or recording paper jam during printing occurred, error
messages are displayed like when original jam occurred in the copier.
Error messages and corrective actions
Error
Memory full
Line is busy
Initial signal not
detected
Terminal constants not
compatible
Training error
CFR not detected
Image signal carrier
not detected
Image signal not
detected
EOL time-out
Post message not
detected
Poor image quality
Image memory error
Software overdrive
Hardware noise
Symptom
Communication was interrupted be-
cause the memory became full.
Redialing was attempted for the
specifiednumber oftimes butthe line
is still busy.
DIS is not detected
Received DIS unable to be handled
Received DCS which is beyond the
capability of the receiver
Fall-back is not made successfully.
Became time-out after FTT was
sent out
CFR (FTT) is not detected
Image signal carrier cannot be de-
tected
High-speed signal cannot be re-
ceived by the receiver
EOL timer exceeded by 13 seconds
Post message is not detected
TX: Received RTN/PIN/ERR
RX:Transmitted RTN/PIN/ERR
Memory is abnormal during the
memory communication
WDTcommunication terminateddue
to software overdrive
Communication terminated due to
software overdrive caused by hard-
ware noise
Message
MEMORY
OVERFLOW
COMMUNICATION
ERROR
COMMUNICATION
ERROR
COMMUNICATION
ERROR
COMMUNICATION
ERROR
COMMUNICATION
ERROR
COMMUNICATION
ERROR
COMMUNICATION
ERROR

October 2000 © TOSHIBA TEC 2 - 1 GD1080/1090 SELF-DIAGNOSIS MODE
2. SELF-DIAGNOSIS MODE
There are two types of the self-diagnosis mode for the fax operation.
• Mode 03, 05 and 08: Some items are added to the modes 03, 05 and 08 of the PPC self-diagnosis
function when the optional fax unit is installed.
• Mode13and 1*:These two modes are newlyadded to the machine whenthefax unit is installed.Started
up by turning ON the power while pressing the specified keys are being pressed.
The followings are the modes which are added to (or extend) the PPC self-diagnosis function.
Turn ON the main switch (power) while pressing two digital keys (ex:“0” and “5”) simultaneously to enter
each mode.
Note : To finish the self-diagnosis mode, turn the power OFF and then back ON.
Do not cancel the mode using the keys “0” and“9”.
(A malfunction may be caused because the start-up process is not per-
formed properly.)
Keys to be pressed
to enter each mode
[0]+[3]+[POWER]
[0]+[5]+[POWER]
[0]+[8]+[POWER]
[1]+[3]+[POWER]
[1]+[✱]+[POWER]
Digital keys on the list output
screen (Do not enter the self-
diagnostic mode)
Function
Output check (modem test, dialing test, CML
test)
Adjustment of the various items
Setting the destination
Setting functions of the various items
Initializationof thevariousmemoryareas (user
registration area, system setting area, image
data area)
Outputs the protocol trace list, dump list and
function setting list
Mode
Test mode
Adjustment mode
Setting mode
Fax function mode
Fax clearing mode
Trace list output
mode
Display
100% C
test mode
100% A
test mode
100% D
test mode
100% F
test mode
100% CL
test mode
Fax screen

GD1080/1090 SELF-DIAGNOSIS MODE 2 - 2 October 2000 © TOSHIBA TEC
2.1 Test Mode (03)
The modem test output, dialing test output and CML test output are performed in the test mode (03).
(1) Modem test/CML test
[Operation procedure]
[0] [3] [FAX] ([FAX]) [Digital key] [START] Operation started [POWER] OFF
[POWER] (Switch line 1 and 2) (Code) (End)
(2) Dialing test
[Operation procedure]
[0] [3] [FAX] ([FAX]) [Digital key] [START] [Digital key]
[POWER] (Switch line 1 and 2) (Code) [START]
[START] [POWER] OFF
(End)
[C/S]
[C/S]

October 2000 © TOSHIBA TEC 2 - 3 GD1080/1090 SELF-DIAGNOSIS MODE
Test code list
Code
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
317
318
319
320
322
Element
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Test
Modem test 2100 Hz
Modem test 14.4 kbps (V.17)
Modem test 9.6 kbps (V.29)
Modem test 4.8 kbps (V.27)
Modem test 300 BPS
Modem test 1850 Hz
Modem test 1650 Hz
Modem test 1100 Hz
Modem test 462 Hz
Modem test 1300 Hz
Modem test 33.6 kbps (V.34)
Modem test 28.8 kbps (V.34)
Modem test 24.0 kbps (V.34)
Modem test 16.8 kbps (V.34)
Dialing test 10PPS (Tested with the digital keys)
(The dial number corresponding to the key which was pressed is kept outputting
on the circuit.The pressed key is displayed on the control panel.)
Dialing test PB (Tested with the digital keys)
(The dial number corresponding to the key which was pressed is kept outputting
on the circuit.The pressed key is displayed on the control panel.)
Modem test 12.0 kbps (V.17)
Modem test 7.2 kbps (V.29)
Modem test 2.4 kbps (V.27ter)
CML test:Turning ON the CML relay

GD1080/1090 SELF-DIAGNOSIS MODE 2 - 4 October 2000 © TOSHIBA TEC
2.2 Adjustment Mode (05)
Parameter setting for the fax image processing is performed in the adjustment mode ‘05’.
(1) Setting parameters for the fax image processing
[Operation procedure]
[SET]
[0] [5] [Digital key] [START] [Digital key] or [POWER] OFF
[POWER] (Code) *[FC] key [INTERRUPT]
(Input adjustment value) (Save the value in the RAM)
[CANCEL] [C/S]
(In case the value is corrected)
* “–” can be entered with the [FC] key.

October 2000 © TOSHIBA TEC 2 - 5 GD1080/1090 SELF-DIAGNOSIS MODE
Code
700
701
702
710
714
715
719
720
724
725
729
Element
Density
Density
Density
Density
Density
Density
Density
Density
Density
Density
Density
Adjustment item
Adjustment of the threshold value for the digitization
Center value
Adjustment of the threshold value for the digitization
Lighter step value
Adjustment of the threshold value for the digitization
Darker step value
Manual-density fine adjustment
Error diffusion, Center value
Manual-density fine adjustment
Error diffusion, Center value
Manual-density fine adjustment
Error diffusion, Lighter step value
Manual-density fine adjustment
Error diffusion, Lighter step value
Manual-density fine adjustment
Error diffusion, Darker step value
Manual-density fine adjustment
Error diffusion, Darker step value
Auto-density fine adjustment
Error diffusion
Auto-density fine adjustment
Error diffusion
Mode
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Fax
Image
quality
mode
Text
Text
Text
Photo
Text/
photo
Photo
Text/
photo
Photo
Text/
photo
Photo
Text/
photo
Default
120
20
20
128
128
12
20
25
20
128
128
Accept-
able
value
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
Adjustment codes for the image processing parameters

GD1080/1090 SELF-DIAGNOSIS MODE 2 - 6 October 2000 © TOSHIBA TEC
2.3 Setting Mode (08)
The destination is set in the setting mode (08).
[Operation procedure]
[CANCEL] [SET]
[0] [8] [Digital key] [START] [Digital key] or [POWER]
[POWER] (Code) (Enter a value) [INTERRUPT] OFF
(Save the value in the RAM)
[C/S]
(In case the value is corrected)
Code
701
Element
Fax
Adjustment item
Destination
1: Asia 2: Australia 3: Hong Kong
4: U.S.A 5: Germany 6: Great Britain
7: Italy 8: Belgium 9: Holland
10: Finland 11: Spain 12: Austria
13: Switzerland 14: Sweden 15: Denmark
16: Norway 17: Portugal 18: France
19: Greece 20: Poland 21: Hungary
22: Czech Rep. 23: Turkey 24:South Africa
Mode
Fax
Image
mode
ALL
Default
AU: 2
UC: 4
EUR: 5
Accept-
able
value

October 2000 © TOSHIBA TEC 2 - 7 GD1080/1090 SELF-DIAGNOSIS MODE
(2) Procedure to confirm the set value
[Operation procedure]
[SET]
[1] [3] [Digital key] [START] or [POWER] OFF
[POWER] (Code) [INTERRUPT]
(Set value cannot be changed)
2.4 Function Mode (13)
Various functions are set in the function mode (13).
(1) Procedure to set the functions
Enter a code using the digital keys and change the set value.
[Operation procedure]
[CANCEL] [SET]
[1] [3] [Digital key] [START] [Digital key] or [POWER]
[POWER] (Code) (Enter a value) [INTERRUPT] OFF
(Save the value in the RAM)
[C/S]
(In case the value is corrected)

October 2000 © TOSHIBATEC 2 - 9 GD1080/1090 SELF-DIAGNOSIS MODEGD1080/1090 SELF-DIAGNOSIS MODE 2 - 8 October 2000 © TOSHIBATEC
Function code list (100-999)
100-299 Adjustment within the dialing standards
100
101
102
103
104
105
106
107
108
109
110
111
112
116
117
DTC frequency (PSTN)
(Line 1)
DTC time (PSTN) (Line 1)
LCC allowed gaps (PSTN)
(Line 1)
DTC allowed gaps (PSTN)
(Line 1)
DTC/LCC for PSTN
(Line 1)
DTC time out (PSTN)
(Line 1)
DTC frequency (PABX)
(Line 1)
DTC time (PABX) (Line 1)
LCC allowed gaps (PABX)
(Line 1)
DTC allowed gaps (PABX)
(Line 1)
DTC/LCC for PABX
(Line 1)
DTC time out (PABX)
(Line 1)
BTC frequency (Line 1)
Dial T1 timer (Line 1)
Dial stop after T1
Set the dial tone frequency to be
detected for the PSTN.
Set the time for a tone sounds to
be determined as dial tone for the
PSTN.
Set the interruption time for the
PSTN to be ignored during LCC.
Set the interruption time for PSTN
to be ignored during DTC.
Select which is to be used for the
PSTN, DTC or LCC.
Set how long the dial tone detec-
tion is performed.
Set the dial tone frequency to be
detected for PABX.
Set the time for a tone sounds to
be determined as dial tone for the
PABX.
Set the interruption time for the
PABX to be ignored during LCC.
Set the interruption time for the
PABX to be ignored during DTC.
Select which is to be used for the
PABX, DTC or LCC.
Set how long the dial tone detec-
tion is performed.
Set the busy tone frequency to be
detected for the PSTN and PABX.
Set the time to wait for a response
from the receiver after dialing is
completed.
IncaseofT1 time-out (no response
from the receiver) during the auto-
matic dialing, redialing is not per-
formedand itis determinedthat the
transmission is terminated due to
error.
0: 300-600Hz 1: 300-650Hz
2: 390-550Hz 3: 400-450Hz
4: 350-480Hz 5: 300-500Hz
6: Reserved 7: Reserved
0: 2sec 1: 800ms 2: 400ms 3: 1sec
4: 1.3sec 5: 1.8sec 6: 2.5sec 7:500ms
0: OFF 1: 50ms 2: 100ms 3: 200ms
0: OFF 1: 70ms 2: 160ms 3: 240ms
0: BZT(DTC/LCC) 1: LCC 5sec
2: DTC only 3: FRN(DTC/LCC)
4: DTC(JPN) 5: NO DTC&LCC
0: 20sec 1: 10sec 2: 8sec 3: 15sec
4: 3.3sec
0: 300-600Hz 1: 300-650Hz
2: 390-550Hz 3: 400-450Hz
4: 350-480Hz 5: 300-500Hz
6: Reserved 7: Reserved
0: 2sec 1: 800ms 2: 400ms 3: 1sec
4: 1.3sec 5: 1.8sec 6: 2.5sec 7: 150ms
0: OFF 1: 50ms 2: 100ms 3: 200ms
0: OFF 1: 70ms 2: 160ms 3: 240ms
0: BZT(DTC/LCC) 1: LCC 5sec
2: DTC only 3: FRN(DTC/LCC)
4: DTC(JPN) 5: NO DTC&LCC
0: 20sec 1: 10sec 2: 8sec 3: 15sec
4: 3.3sec
0: Not detected 1: 300-600Hz
2: 350-550Hz 3: 300-500Hz
4: 300-700Hz
0: 60sec 1: 35sec 2: 90sec
3: 55sec 4:115sec
0: OFF 1: ON
000011111111111111111100100
000322222222222222222200101
000322222222222222222200102
000322222222222222222200103
555222222222222222222255104
000111111111111111111100105
000011111111111111111100106
000622222222222222222200107
000033333333333333333300108
000033333333333333333300109
555255555555555555555555110
000111111111111111111100111
000111111111111111111100112
030322222222222222222200116
000100000000000000000000117
Code Adjustment Function Setting Default Code
AS AU HK US DE GB IT BE NL FI ES AT CH SE DK NO PT FR GR PL HU CZ TR ZA

October 2000 © TOSHIBATEC 2 - 11 GD1080/1090 SELF-DIAGNOSIS MODEGD1080/1090 SELF-DIAGNOSIS MODE 2 - 10 October 2000 © TOSHIBATEC
Code Adjustment Function Setting Default Code
AS AU HK US DE GB IT BE NL FI ES AT CH SE DK NO PT FR GR PL HU CZ TR ZA
0: Normal 1: Shift 2: Reverse
0: OFF 1: ON
0: No retry
1: 1 redialing
¦
14: 14 redialings
0: 0sec 1: 1sec 2: 2sec 3: 4sec
4: 3.3sec 5:10sec
0: 900ms 1: 550ms 2: 700ms 3: 800ms
0: Default (3 min)
1: 1min
¦
15: 15min
0: 60/40(10PPS) 1: 67/33(10PPS)
2: 63/37(10PPS) 3: 50/50(10PPS)
4: 67/33(20PPS)
0: 80/80ms 1: 70/70ms 2: 70/150ms
3: 60/60ms 4: 80/100ms 5: 150/50ms
6: 150/240ms
0: -24dBm 1: -27dBm 2: -30dBm
3: -33dBm 4: -36dBm 5: -39dBm
6: -42dBm 7: -45dBm
0: -24dBm 1: -27dBm 2: -30dBm
3: -33dBm 4: -36dBm 5: -39dBm
6: -42dBm 7: -45dBm
0: 0dB
1: -1dB
¦
15: -15dB
(Value decreased one by one)
125
127
128
129
132
135
137
138
139
140
141
Dial information (Line 1)
Internal retry
Redialing counter
Time for a pause (Line 1)
Interdigit pause (Line 1)
Redialing interval (Line 1)
DP make/break ratio
(Line 1)
MF timing (Line 1)
DTC RX ATT (PSTN)
(Line 1)
DTC RX ATT (PABX)
(Line 1)
MF TX-ATT (Line 1)
Set the definition of the DP dial.
Normal: n
Shift: n+1
Reverse: 10-n
n=Dial No.
Whendialing is interruptedbecause
any of the settings for DTC/LCC is
not satisfied during redialing, that
redialing is ignored since it is con-
sidered as an internal retry.
Set the number of redialings.
Set the time for a pause when it is
inserted between the dialnumbers.
Set the interval between digits for
DP dialing.
Setthe interval between redialings.
Set the make/break ratio for DP
dialing.
Set the ON/OFF timing of MF sig-
nals. Do not set the value “4” for the
function code 138 and 268 to en-
sure minimum time of the MF sig-
nal duration ruled in TBR21 (Re-
quirement 4.8.2.4, 4.8.2.5)
Set the reception level when the
dial tone is detected for the PSTN.
Set the reception level when the
dial tone is detected for the PABX.
Set the attenuator value for the MF
signal.
000000000000010200000000125
000011000001001100000000127
524534335331454935433355128
422422320222022212444444129
002303322013322220330000132
313100322022210013333333135
111001010010001011010011137
202440011020012000403122138
666666666666666666666666139
666666666666666666666666140
365355555555555555555533141

October 2000 © TOSHIBATEC 2 - 13 GD1080/1090 SELF-DIAGNOSIS MODEGD1080/1090 SELF-DIAGNOSIS MODE 2 - 12 October 2000 © TOSHIBATEC
Code Adjustment Function Setting Default Code
AS AU HK US DE GB IT BE NL FI ES AT CH SE DK NO PT FR GR PL HU CZ TR ZA
00: No detection 01: 300Hz-600Hz
02: 300Hz-650Hz 03: 390Hz-550Hz
04: 400Hz-450Hz 05: 350Hz-480Hz
06: 300Hz-500Hz
07: France Dual Tone (not used)
10: No detection 11: 300Hz-600Hz
12: 300Hz-650Hz 13: 390Hz-550Hz
14: 400Hz-450Hz 15: 350Hz-480Hz
16: 300Hz-500Hz
17: France Dual Tone (not used)
Numeric value of 3 digits
(Default setting:4 digits)
0: OFF 1: -3dB
0: 80-650ms 1: 450-550ms
2: 200-650ms 3: 400-600ms
4: 120-550ms 5: 420-610ms
6: Reserved 7: Reserved
0: 80-650ms 1: 450-550ms
2: 200-650ms 3: 400-600ms
4: 160-600ms 5: 170-700ms
6: 380-630ms 7: 150-470ms
0: 0dB
1: -1dB
|
4: -4dB (Value decreased one by one)
0: OFF 1: ON
0: PSTN 1: PABX
0: Not defined 1: Local/Distant
2 : Access Digit
0: DP 1: MF
Numeric value of 3 digits (4 digits for the
default setting)
0: PSTN 1: PABX
0: Not defined 1: Local/Distant
2 : Access Digit
0: DP 1: MF
Numeric value of 3 digits (4 digits for the
default setting)
142
143
149
150
151
152
153
200
201
203
206
210
211
213
216
International DTC fre-
quency
International dial access
code(Line 1)
ATT control (Line 1)
BTC ON time (Line 1)
BTC OFF time (Line 1)
MF dial levels
Intermittent DTC function
Exchange type (Line 1)
Dial selection (Line 1)
Dialer type (Line 1)
Local/distant dial (Line 1)
Exchange type (Line 2)
Dial selection (Line 2)
Dialer type (Line 2)
Local/distant dial (Line 2)
Select the frequency range for the
dial tone of the first pause to be
detected.
Select the frequency range for the
dialtonetobe detected after dialing
the second international dial ac-
cess code.
Setsthe international access code.
Setting for the receiver attenuator.
Sets time that a busy-tone signal
is output to be determined it is ON.
Sets time that a busy-tone signal
is not output to be determined it is
OFF.
Setthedifferencebetween the high
output and low output of the MF
signal.
Setting for intermittent DTC func-
tion.
Select the exchange type.
Select the access type for the
PABX.
Select the dial type.
Enter an access code designated
for the access type selected for the
function code 201.
Local: 2 digits
Distant: 2 digits
Access Digit: 3 digits
Select the exchange type.
Select the access type for the
PABX.
Select the dial type.
Enter an access code designated
for the access type selected for the
function code 211.
Local: 2 digits
Distant: 2 digits
Access Digit: 3 digits
000000000000000000000000142
1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 143
000000000000000000000000149
000000000000000000000000150
000000000000000000000000151
212222222222222222222222152
000000100000000000000000153
000000000000000000000000200
111111111111111111111111201
111111111111111111111111203
1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 206
000000000000000000000000210
111111111111111111111111211
111111111111111111111111213
1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 216

October 2000 © TOSHIBATEC 2 - 15 GD1080/1090 SELF-DIAGNOSIS MODEGD1080/1090 SELF-DIAGNOSIS MODE 2 - 14 October 2000 © TOSHIBATEC
Code Adjustment Function Setting Default Code
AS AU HK US DE GB IT BE NL FI ES AT CH SE DK NO PT FR GR PL HU CZ TR ZA
Set the dial tone frequency to be
detected for the PSTN.
Set the time for a tone sounds to
be determined as dial tone for the
PSTN.
Set the interruption time for the
PSTN to be ignored during LCC.
Set the interruption time for the
PSTN to be ignored during DTC.
Select which is to be used for the
PSTN, DTC or LCC.
Set how long the dial tone detec-
tion is performed.
Set the dial tone frequency to be
detected for the PABX.
Set the time for a tone sounds to
be determined as dial tone for the
PABX.
Set the interruption time for the
PABX to be ignored during LCC.
Set the interruption time for the
PABX to be ignored during DTC.
Select which is to be used for the
PABX, DTC or LCC.
Set how long the dial tone detec-
tion is performed.
Set the busy tone frequency to be
detected for the PSTN and PABX.
Set the time to wait for a response
from the receiver after dialing is
completed.
Set the definition of the DP dial.
Normal: n
Shift: n+1
Reverse: 10-n
n=Dial No.
Whendialing is interruptedbecause
any of the settings for DTC/LCC is
not satisfied during redialing, that
redialing is ignored since it is con-
sidered as an internal retry.
0: 300-600Hz 1: 300-650Hz
2: 390-550Hz 3: 400-450Hz
4: 350-480Hz 5: 300-500Hz
6: Reserved 7: Reserved
0: 2sec 1: 800ms 2: 400ms 3: 1sec
4: 1.3sec 5: 1.8sec 6: 2.5sec
7: 500ms
0: OFF 1: 50ms 2: 100ms 3: 200ms
0: OFF 1: 70ms 2: 160ms 3: 240ms
0: BZT(DTC/LCC) 1: LCC 5sec
2: DTC only 3: FRN(LCC/DTC)
4: DTC(JPN&USA) 5: NO DTC&LCC
0: 20sec 1: 10sec 2: 8sec 3: 15sec
4: 3.3sec
0: 300-600Hz 1: 300-650Hz
2: 390-550Hz 3: 400-450Hz
4: 350-480Hz 5: 300-500Hz
6: Reserved 7: Reserved
0: 2sec 1: 800ms 2: 400ms 3: 1sec
4: 1.3sec 5: 1.8sec 6: 2.5sec 7: 150ms
0: OFF 1: 50ms 2: 100ms 3: 200ms
0: OFF 1: 70ms 2: 160ms 3: 240ms
0: BZT(DTC/LCC) 1: LCC 5sec
2: DTC only 3: FRN(LCC/DTC)
4: DTC(JPN&USA) 5: NO DTC&LCC
0: 20sec 1: 10sec 2: 8sec 3: 15sec
4: 3.3sec
0: Not detected 1: 300-600Hz
2: 350-550Hz 3: 300-500Hz
4: 300-700Hz
0: 60sec 1: 35sec 2: 90sec 3: 55sec
4: 115sec
0: Normal 1: Shift 2: Reverse
0: OFF 1: ON
220
221
222
223
224
225
226
227
228
229
230
231
232
236
245
247
DTC frequency (PSTN)
(Line 2)
DTC time (PSTN) (Line 2)
LCC allowed gaps (PSTN)
(Line 2)
DTC allowed gaps (PSTN)
(Line 2)
DTC/LCC for PSTN
(Line 2)
DTC time out (PSTN)
(Line 2)
DTC frequency (PABX)
(Line 2)
DTC time (PABX) (Line 2)
LCC allowed gaps (PABX)
(Line 2)
DTC allowed gaps (PABX)
(Line 2)
DTC/LCC for PABX
(Line 2)
DTC time out (PABX)
(Line 2)
BTC frequency(Line 2)
Dial T1 timer (Line 2)
Dial information (Line 2)
Internal retry (Line 2)
000011111111111111111100220
000322222222222222222200221
000322222222222222222200222
000322222222222222222200223
555222222222222222222255224
000111111111111111111100225
000011111111111111111100226
000622222222222222222200227
000033333333333333333300228
000033333333333333333300229
555555555555555555555555230
000111111111111111111100231
000111111111111111111100232
030322222222222222222200236
000000000000010200000000245
000011000001001100000000247