Toshiba B-EX4 T1 Series Manual

Toshiba - B-EX4T1 Printer SetupToshiba - B-EX4T1 Printer Setup
B-EX4T1 Printer Setup for Auto Labeling
EasyEasy 20 20 minute(s)minute(s)
Difculty Duration
ContentsContents
Step 1 - Inner & Outer
Step 2 - Rewind Spool
Step 3 - Printhead access
Step 4 - Setting Rewinder
Step 5 - Label Guides
Step 6 - Sensor Position
Step 7 - Closing Label Head
Step 8 - Connecting printer to PC
Step 9 - Initial Power up
Step 10 - Using BCP to setup the printer
Step 11 - Change Settings
Step 12 - Power printer off and On
Step 13 - Testing
Step 14 - Set the IP Address for the Customers network
Comments
Step 1 - Inner & Outer
The instructions for both the Inner & Outer wound labels are on the
inside of the open lid.
Page 1 / 6

Step 2 - Rewind Spool
There will be no ribbon and as the settings will be for Peel Off a
length of blank backing needs to be fed onto the Rewind spool
Step 3 - Printhead access
To gain access turn the green knob to FREE. You can then pull the
front plate down and lift the printer head up.
Step 4 - Setting Rewinder
Ensure the switch is set to REWINDER
Page 2 / 6

Step 5 - Label Guides
With the Printhead open ensure that the labels are under the small
black sprung guides. Slide the green guide to the width of the label.
Step 6 - Sensor Position
Ensure that the sensor head is in the middle of the label
Step 7 - Closing Label Head
When loaded close the Printhead down, lift the front plate up and
turn the green knob to LABEL.
Step 8 - Connecting printer to PC
For easy setup use a USB cable (Alternatively everything can be done via the network web interface)
1) Connect a USB cable to the PC
2) Connect a Network cable to a live DHCP network to obtain an IP address.
3) Download and install the BCP setup software: https://www.toshibatec.com/download_overseas/printer/setting_tool/BCP_Series/ [1]
Page 3 / 6

Step 9 - Initial Power up
If the labels have been tted properly on power up the calibration
process will eject several labels.
Take a note of the IP address given to the printer on the front panel.
Step 10 - Using BCP to setup the
printer
When you start BCP you should see as picture
Select USB if not Selected
Page 4 / 6

Step 11 - Change Settings
Press the Emulation Button and take the top option "Zmode System Parameter Settings"
Then Make the changes
Label Length 38mm38mm (after calibration this will be reset to 41.3)
Label Width 98mm98mm
Ribbon WITHOUT RIBBONWITHOUT RIBBON
Print mode PEEL OFFPEEL OFF
Sensor TRANS PREPRINTTRANS PREPRINT
Max Label Length (for calibration) 200mm200mm (this just saves on labels)
Press the DOWNLOADDOWNLOAD button and check that there are no errors.
Now on the Toshiba side:
Select Paraeter Settings
Select Standard 2 (General 2 on BCP TOOL)
Adjust Cut Adjust to -2.0
Press the submit button
The screen shows the Web version. The adjustment brings the label forward out of the printer to allow collection by the Picking Arm.

Step 12 - Power printer off and On
...This is often necessary to make sure the printer returns in emulation mode properly
Step 13 - Testing
1) Pressing "Feed" should push out another label regardless.
2) Send a label to the printer via the network (or via the Test - Send
le within BCP).
3) Send more than one le and make sure that each time you
remove a label from the output the next one is presented.
Page 5 / 6

Step 14 - Set the IP Address for the
Customers network
1. Within BCP choose "Parameter Settings"
2. Select the LAN tab
3. Enable TCP/IP
4. Enable Wired LAN
5. Set IP Address and Sub Net Mask
6. Press the Set Parameter at the bottom.
Page 6 / 6