Toshiba Carrier TCB-AX21UL User manual

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)
Installation Manual
Installation Manual
Remote controller for air
conditioner (Split type) 1
English
Manuel du proprietaire
Télécommande pour climatiseur
(Type split) 15
Français
Remote Controller
Model name:
Wireless remote controller kit
TCB-AX21UL
Generic model name Wireless remote controller
and Signal receiving unit
TCB-AX21UL WX-TA01UES
(Wireless remote controller
model name)
Wireless remote controller
(WX-TA01UES)
Signal receiving
unit
+00EH99677601_01EN_remo_IM.book Page 1 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–1–
Contents
1 ACCESSORY PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT . . . . . . . . . . 3
3 INSTALLATION LOCATION OF SIGNAL RECEIVING UNIT . . . . 4
4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT . . . . . . . . . . . 5
5
HOW TO PERFORM CABLING OF THE SIGNAL RECEIVING UNIT . . . 8
6 REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7 HOW TO SET THE ROOM TEMPERATURE SENSOR . . . . . . . . 10
8 HOW TO SET THE ADDRESS SWITCH . . . . . . . . . . . . . . . . . . . 11
9 SLIDE SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
10 SELF-DIAGNOSIS TABLE AND MEASURES . . . . . . . . . . . . . . . 12
11
CAUTIONS FOR INSTALLATION OF THE REMOTE CONTROLLER . . 12
12 EXPLANATION TO CUSTOMERS . . . . . . . . . . . . . . . . . . . . . . . . 13
13 HOW TO HANDLE THE REMOTE CONTROLLER . . . . . . . . . . . 13
14 TEST RUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Thank you very much for purchasing TOSHIBA/Carrier Remote Controller for Air
Conditioner.
Please read the owner's manual carefully before using your Remote Controller for Air
Conditioner.
• Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or
dealer).
Request to constructor or dealer
• Please clearly explain the contents of the Owner’s manual and hand over it.
1-EN
+00EH99677601_01EN_remo_IM.book Page 1 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–2–
EN
1ACCESSORY PARTS
No. Parts Quantity
1Signal receiving unit
(provided 7.9” (200 mm) power cable) 1
2 Mounting bracket 1
3 Screws ∅0.16” x 1.0” (M4 x 25 mm) 2
4 Screws ∅0.16” x 1.6” (M4 x 40 mm) 2
5 Wood screws 2
6 Spacer 4
7 Wire joints 2
8 Cable tie 1
9Pattern template
3.7” x 2” (95 mm x 51 mm) 1
10 Remote controller 1
11 Remote cotroller holder 1
12 Truss tapping screw,
∅0.16” x 0.63” (M4 x 16 mm) 2
13 Installation manual 1
14 Owner’s manual 1
2-EN
+00EH99677601_01EN_remo_IM.book Page 2 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–3–
2SWITCH LOCATION OF SIGNAL RECEIVING
UNIT
13
2
46
5
Screw
Remove Face plate Remove the face plate from Signal receiving unit.
Signal receiving unit
Address selector switch
This switch is used to address one of a
maximum of six air conditioners that can
be controlled by the remote controller.
(Refer to page 11.)
Allx{/NORMAL selector switch
Set this switch to the “NORMAL” position for the normal operation of the air conditioner. When this switch is set to the
“Allx{” position, the indoor unit of the air conditioner is turned off.
RCU:SUB/RCU:MAIN selector switch
Set this switch to the “RCU:MAIN” position for normal operation. Refer to page 9 for setting to the “RCU:SUB” position.
PCB CHK switch
This switch is not used and should be set in the position shown in the figure.
TEST RUN switch
This switch is used for test running.
3-EN
+00EH99677601_01EN_remo_IM.book Page 3 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–4–
EN
3INSTALLATION LOCATION OF SIGNAL
RECEIVING UNIT
• Do not install in a location where the air contains oil mist, such as in a kitchen or factory.
• Do not install next to a window, or in any other location directly exposed to sunlight and
outside air.
• Do not install nearby devices which can be expected to produce electrical noise, such as
elevators, automatic doors, and industrial sewing machines.
• If the Signal receiving unit is installed near a rapid-start type or inverter-type fluorescent
lamp (a lamp which does not include a glow lamp), it may not be possible to receive the
wireless remote controller signal in some cases. In order to prevent interference from
fluorescent lamps, leave a minimum of 6’7” (2 m) between the Signal receiving unit and
the fluorescent lamps, and install the Signal receiving unit in a location where it can receive
the wireless remote controller signal when the fluorescent lamps are lit.
4-EN
+00EH99677601_01EN_remo_IM.book Page 4 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–5–
4HOW TO INSTALL THE SIGNAL RECEIVING
UNIT
NOTE
• To avoid malfunction of the remote controller, do not assemble or run remote control
wiring together with the power cables, and do not enclose them in the same metal
conduit.
• When the power unit induces electrical noise, it is recommended that a noise filter or the
like be installed.
For flush mounting into a wall, install the Signal receiving unit in a metal
switch box (field supply) that has been recessed into the wall in advance.
1. Insert a flathead screwdriver or similar
tool into the notch, and remove the
face plate.
2. Fix the Signal receiving unit with 2
∅0.16” (4 mm) screws provided. Do
not overly tighten, and use the
provided spacers. If the Signal
receiving unit does not fit in the wall,
cut spacers to adjust the clearance.
3. Connect the Signal receiving unit
wiring (2-core cable) with the cables
extended from the indoor unit.
(Refer to the section on Signal receiving unit wiring.)
Be sure to determine the correct terminal numbers on the indoor unit when wiring the Signal
receiving unit. The remote controller will be damaged if high voltage (such as 208/230 VAC) is
applied.
4. Reattach the face plate.
When using exposed mounting for the Signal receiving unit, install onto
a wall where the Signal receiving unit can be attached.
1. Insert a straight blade screwdriver or similar
tool into the groove on the bottom of the
Signal receiving unit. Pry open with the
screwdriver and remove the lower case.
(Fig. A).
13
2
46
5
Signal receiving unit
Spacer
Screw
∅0.16” x 1.0” (M4 x 25 mm)
Face plate
Remove
Screw
Face plate
Fig.A
5-EN
+00EH99677601_01EN_remo_IM.book Page 5 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–6–
EN
2. In order to later pass the Signal receiving
unit wiring out through the upper case (thin
part at the top center), use nippers or a
similar tool to cut a notch in the same size as
the Signal receiving unit cord (optional).
(Fig. B)
3. Disconnect the wires that were connected to
the connector at the time of shipment.
4. Fasten the Signal receiving unit cord
(optional) at the position shown in Fig. C,
using the provided cable tie. Then connect
the cord to the Signal receiving unit
connector.
5. Shape the Signal receiving unit cord as
shown in Fig. C so that it fits at the top inside
the Signal receiving unit, above the PCB.
Then attach the lower case. At this time,
bend the head of the cable tie so that it faces
sideways.
6. Remove the nameplate and use 2 wood screws to attach the Signal receiving unit.
7. Use the provided cord clips to fasten the Signal receiving unit cord to the wall.
8. Reattach the face plate.
If the separate Signal receiving unit is installed on the ceiling, use the
provided ceiling mounting bracket for installation.
1. Insert a screwdriver or similar tool into the notch at the
bottom to remove the Signal receiving unit face plate.
2. Cut a section out of the ceiling along the provided paper
pattern (3.7” x 2” (95 x 51 mm)).
3. Pass the wire through the provided mounting bracket and
insert the bracket into the installation hole. (Fig. D)
Cable tie
0.08”-0.12”
(2–3 mm)
Signal receiving
unit cord
(optional)
Fig.B
Notch where Signal
receiving unit cord
passes through top case
Connector
13
2
46
5
Signal
receiving unit
Wood
screws (2)
Fig.C
Signal receiving unit cord
(optional)
Clamp
Fig.D
6-EN
+00EH99677601_01EN_remo_IM.book Page 6 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–7–
4. Use bracket parts (A) and (B) to securely grip the ceiling
material. (Fig. E)
5. Connect the Signal receiving unit wire (2-core) to the wire
from the indoor unit. (Refer to “Wiring the Signal receiving
unit.”) Check the terminal number on the indoor unit
before wiring the Signal receiving unit and be sure not to
wire incorrectly. (The unit will be damaged if high voltage,
such as 208/230 VAC, is applied.)
6. Adjust the provided spacers so that they are several
millimeters larger than the thickness of the ceiling
material. Pass the 2 supplied screws (0.16” x 1.6” (M4 x
40 mm)) through the spacers and tighten them enough to
hold the Signal receiving unit in place.
7. Return parts (A) and (B) through the gap between the
ceiling and Signal receiving unit so that they are
contained in the openings. Then tighten the screws.
Do not tighten the screws excessively. This may result in
damage or deformation of the case.
Tighten to the point where the Signal receiving unit can be
moved slightly by hand. (Fig. F)
8. Reattach the face plate.
Part (A)
Fig.E
Part (B)
Fig.F
7-EN
+00EH99677601_01EN_remo_IM.book Page 7 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–8–
EN
5HOW TO PERFORM CABLING OF THE
SIGNAL RECEIVING UNIT
Flush Mounting
Connection diagram
Provided wire joint (WHT 2)
1. Strip the insulation to approximately 0.55” (14 mm) from the ends of the wires to be connected.
2. Twist together the 2 wires and create a crimp connection at the wire joint.
3. If a special crimping tool is not used, or if the connection is soldered, insulate the wires using
insulation tape.
Exposed Mounting
• Connection diagram
Signal receiving unit
Power wire from
Signal receiving unit
Connector
Wire of Signal receiving
unit (Field procurement)
(AWG20 (0.5 mm2))
(UL wires rated 300 V)
Indoor unit remote
controller terminal
board
Wire of Signal
receiving unit
(Field procurement)
Wire joint
(provided)
Power wire from
Signal receiving
unit
Indoor unit remote
controller terminal
board
Signal receiving unit
Remote controller cord (optional)
8-EN
+00EH99677601_01EN_remo_IM.book Page 8 Thursday, October 8, 2009 4:12 PM

Wireless remote controller kit Installation Manual
–9–
6REQUIREMENT
The control by two remote controllers is enabled by installing the wireless remote controller
with the wired remote controller for an indoor unit.
(Max. 2 remote controllers of wireless or wired are insatiable.)
“2-remote controllers” controlling means that one or multiple units are operated by the
multiple remote controllers.
NOTE
1. Upon confirmation of the terminal numbers of the indoor unit, connect the remote
controller cables without miscabling. (If applied AC 208/230 Volt, damage the unit.)
2. The multiple wireless remote controller kits cannot concurrently be used for an indoor
unit.
3. When installing simultaneously the wireless remote controller with the wired remote
controller, set one of them as the sub remote controller.
• When setting the wired remote controller as the sub, exchange the address connector
at the rear of P.C. board of wired remote controller from master to sub remote
controller.
• When setting the wireless remote controller as the sub, turn the switch of wireless
remote controller Signal receiving unit from RCU: MAIN to RCU:SUB.
To operate an indoor unit by 2 remote controllers
The indoor unit is operated if either wireless or wired remote controller is set as MAIN or SUB
remote controller.
(Total cable length: Within 1312’4” (400 m))
Wireless remote
controller kit
Wired remote
controller (SUB)
(Sold separately)
Remote controller cable
(Procured locally)
(AWG20 (0.5 mm2))
(UL wires rated 300 V)
Indoor unit
Earth
Terminal block for
remote controller
cable
Signal receiving unit
9-EN
+00EH99677601_01EN_remo_IM.book Page 9 Thursday, October 8, 2009 4:12 PM