TOTALINE Smart 1H/1C User manual

Operating
Manual
Totaline® Smart 1H/1C and 2H/2C
Programmable P330 Series Thermostat
570-212
69-2265EFS-01
®

ENGLISH
Quick Reference Card
Grasp and pull to see basic operating instructions at a glance.
Batteries should be replaced once a year (see
page 14).
This manual covers the following models:
P330 -1110: For 1 Heat/1 Cool systems
P330-1220: For up to 2 Heat/2 Cool systems
M27927
HOLD
Read and save these instructions.
® U.S. Registered Trademark. Patents pending.
All rights reserved.
Need Help?
Visit www.Totaline.com.

P330 Series
570-212 1 69-2265EFS—01
ENGLISH
About your new thermostat
Quick reference to controls.......................2
Quick reference to display ........................3
Programming & Operation
Set time and day........................................4
Select fan setting (auto/on) ....................... 5
Select system setting (heat/cool)..............6
Using program schedules .........................7
Program schedule overrides .....................9
Auto-changeover (heat/cool)...................11
Compressor protection............................12
Early Recovery .........................................13
Appendices
Battery replacement ................................14
Troubleshooting .......................................15
Customer assistance ............................... 16
Accessories/replacement parts .............. 16
Warranty ...................................................17
This thermostat is ready to go!
Your new thermostat is pre-programmed
and ready to go.
Table of contents
CAUTION: EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not operate
cooling system when outdoor
temperature is below 50°F (10°C).

Operating Manual
69-2265EFS—01 2 570-212
ENGLISH
M27924
HOLD
Digital display
(see page 3).
Temperature Buttons
Press to adjust temperature
settings (see page 7–8).
Hold Button
Press to override
programmed temperature
control (see page 10).
Function Buttons
Press to select the function displayed just above each
button. (Functions change depending on the task.)
Quick reference to controls

P330 Series
570-212 3 69-2265EFS—01
ENGLISH
M27874
Current inside temperature
Early Recovery
(see page 13)
Current program period
Period 1/2/3/4 (see pages 7-8)
Set Time/Day/Program
(see pages 4 & 7)
Function buttons
Press the button beneath each function to
view or change settings (functions change
depending on the task)
Low battery warning
(see page 14)
Current time/day
(see page 4)
Temperature setting
(see pages 7–8)
Auxiliary heat
(Only for heat pumps
with auxiliary heat)
System status
Heat /Cool (If
flashing, see page 12)
System setting
Heat/Cool/Auto/Off/Em
Heat (see page 6)
Fan setting
Auto/On (see page 5)
Quick reference to display screen

Operating Manual
69-2265EFS—01 4 570-212
ENGLISH
1. Press the SET TIME/DAY/PROGRAM but-
ton, then press s or t to set the
clock time.
2. Press the CHOOSE DAY button, then
press s or t to select the day of the
week.
3. Press DONE to save & exit.
Note: If the SET TIME/DAY/PROGRAM option is not
displayed, press DONE or SET PROGRAM.
Note: If the display flashes Set Time, the
thermostat will follow your settings for the
weekday time period until you reset the time
and day.
Set the time and day
Press SET TIME/DAY/PROGRAM, then adjust time
Press CHOOSE DAY, then select current day
M27875
HOLD
M27876
HOLD

P330 Series
570-212 5 69-2265EFS—01
ENGLISH
M27877
M27878
Press the FAN button to select Auto or On.
In “Auto” mode (the most commonly used
setting), the fan runs only when the heating
or cooling system is on. If set to “On,” the fan
runs continuously.
Select the fan setting

Operating Manual
69-2265EFS—01 6 570-212
ENGLISH
Note: The Auto and Em Heat
system settings may not
appear, depending on how your
thermostat was installed.
Press the SYSTEM button to select:
• Heat: Thermostat controls only the
heating system.
• Cool: Thermostat controls only the
cooling system.
• Off: Heating and cooling systems are off.
• Auto: Thermostat automatically selects
heating or cooling depending on the
indoor temperature.
• Em Heat (only for heat pumps with
auxiliary heat): Thermostat controls
Emergency and Auxiliary Heat.
Compressor is locked out.
Select the system setting
M27877
M27879

P330 Series
570-212 7 69-2265EFS—01
ENGLISH
To restore Energy Star
default settings:
Period 1
(6:00 am)
Period 2
(8:00 am)
Period 3
(6:00 pm)
Period 4
(10:00 pm)
Cool
(Mon-Fri)
Heat
(Mon-Fri)
Heat
(Sat-Sun)
Cool
(Sat-Sun)
70 °75 °70 °75 °
62 °83 °62 ° [Or cancel
period]
83 °
[Or cancel
period]
70 °75 °70 ° [Or cancel
period]
75 °
[Or cancel
period]
62 °78 °62 °78 °
This thermostat is pre-set to use Energy Star®program settings.
Energy Star®settings for maximum cost savings
1. Press SET TIME/DAY/
PROGRAM.
2. Press SET PROGRAM.
3. Press DONE and NEXT
at the same time for 4
seconds.

Operating Manual
69-2265EFS—01 8 570-212
ENGLISH
1. Press SET TIME/DAY/PROGRAM, then SET
PROGRAM.
2. Press s or t to set your weekday Period 1
time (Mon–Fri), then press NEXT.
3. Press s or t to set the temperature for this
time period, then press NEXT.
4. Set time and temperature for the next time
period (Period 2). Repeat steps 2 and 3 for
each weekday time period.
5. Press NEXT to set weekend time periods (Sat-
Sun), then press DONE to save & exit.
Note: Make sure the thermostat is set to the system you
want to program (Heat or Cool).
Note: You can press CANCEL PERIOD to eliminate unwanted
time periods (except Period 1).
To adjust program schedules
M27879
M27880
M27881
HOLD

P330 Series
570-212 9 69-2265EFS—01
ENGLISH
M28595
HOLD
Press s or t to immediately adjust
the temperature. This will temporarily
override the temperature setting for the
current time period.
The new temperature will be
maintained only until the next
programmed time period begins (see
page 7). For example, if you want to
turn up the heat early in the morning,
it will automatically be lowered later,
when you leave for the day.
To cancel the temporary setting at any
time, press RUN PROGRAM.
Press to cancel temporary setting and
resume program schedule.
Note: Make sure the thermostat is set
to the system you want to control (heat,
cool or auto).
Press to temporarily adjust temperature.
Program schedule override (temporary)

Operating Manual
69-2265EFS—01 10 570-212
ENGLISH
Press to cancel “Hold” setting and
resume program schedule.
Note: Make sure the thermostat is set
to the system you want to control (heat,
cool or auto).
Press to permanently adjust temperature. Press HOLD to permanently adjust
the temperature. This will override
the temperature settings for all time
periods.
The “Hold” feature turns off the
program schedule and allows you to
adjust the thermostat manually, as
needed.
Whatever temperature you set will
be maintained 24 hours a day, until
you manually change it, or press RUN
PROGRAM to cancel “Hold” and resume
the programmed schedule.
Program schedule override (permanent)
M27883
HOLD

P330 Series
570-212 11 69-2265EFS—01
ENGLISH
Auto Changeover is a feature used in
climates where both air conditioning and
heating are used on the same day. When
the system is set to Auto, the thermostat
automatically selects heating or cooling
depending on the indoor temperature.
Heat and cool settings must be at least
3 degrees apart. The thermostat will
automatically adjust settings to maintain this
3-degree separation (called “deadband”).
The 3-degree separation between heating
and cooling set temperatures is fixed, and
cannot be changed.
Press until screen
displays “Auto”
Note: The Auto system setting
may not appear, depending on
how your thermostat was installed.
Auto Changeover (heat/cool)
M27884

Operating Manual
69-2265EFS—01 12 570-212
ENGLISH
M27885
This feature helps prevent damage to the
compressor in your air conditioning or heat
pump system.
Damage can occur if the compressor is
restarted too soon after shutdown. This fea-
ture forces the compressor to wait for a few
minutes before restarting.
During the wait time, the display will flash the
message Cool (or Heat if you have a heat
pump). When the safe wait time has elapsed,
the message stops flashing and the compres-
sor turns on.
Message flashes until safe restart
time has elapsed
Built-in compressor protection

P330 Series
570-212 13 69-2265EFS—01
ENGLISH
Note: When Early Recovery is in effect, the thermostat will display “Recovering”.
Early Recovery
Early Recovery eliminates guesswork when setting your schedule. It allows the ther-
mostat to “learn” how long your furnace and air conditioner take to reach the tem-
perature you want.
Just set your program schedule to the time you want the house to reach your desired
temperature. The thermostat then turns on the heating or cooling at just the right time
to reach your scheduled temperature at your scheduled time.
For example: Set the Period 1 time to 6 am and the temperature to 70°. The heat will
come on before 6 am, so the temperature is 70° by the time you wake at 6.

Operating Manual
69-2265EFS—01 14 570-212
ENGLISH
Batteries are optional (to provide backup
power) if your thermostat was wired to run on
AC power when installed.
Install fresh batteries immediately when
the warning begins flashing. The
warning flashes about two months before the
batteries are depleted.
Even if the warning does not appear, you
should replace batteries once a year, or
before leaving home for more than a month.
If batteries are inserted within two minutes,
the time and day will not have to be reset.
All other settings are permanently stored in
memory, and do not require battery power.
Insert fresh AA
alkaline batteries.
Battery Replacement
M28596

P330 Series
570-212 15 69-2265EFS—01
ENGLISH
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions.
Display is blank • Checkcircuitbreakerandresetifnecessary.
• Makesurepowerswitchatheating&coolingsystemison.
• Makesurefurnacedoorisclosedsecurely.
• Ifthermostatisbatterypowered,makesurefreshAAalkaline
batteries are correctly installed (see page 14).
Heating or
cooling system
does not respond
• PressSYSTEM button to set system to Heat. Make sure the
temperature is set higher than the Inside temperature.
• PressSYSTEM button to set system to Cool. Make sure the
temperature is set lower than the Inside temperature.
• Checkcircuitbreakerandresetifnecessary.
• Makesurepowerswitchatheating&coolingsystemison.
• Makesurefurnacedoorisclosedsecurely.
• Wait5minutesforthesystemtorespond.

Operating Manual
69-2265EFS—01 16 570-212
ENGLISH
Visit www.Totaline.com.
Accessories/replacement parts
Contact your heating/cooling contractor for replacement parts.
Cover plate assembly* ...................................Part No. P350-CP-MULTI
*Use to cover marks left by old thermostats.
Customer assistance

P330 Series
570-212 17 69-2265EFS—01
ENGLISH
Limited Five-Year Warranty
FIVE-YEAR WARRANTY—This CARRIER CORPORATION product is warranted to be free from defects in
material and workmanship under normal use and maintenance for a period of five years from the date of
original installation. A new or remanufactured part to replace the defective part will be provided without
charge for the part itself, through a qualified servicing CARRIER CORPORATION dealer or service, provided
the defective part is returned to our distributor. The replacement part assumes the unused portion of the
warranty.
THIS WARRANTY DOES NOT INCLUDE ANY ADDITIONAL LABOR ALLOWANCE OR OTHER COSTS incurred
for diagnosis, repairing, removing, installing, shipping, servicing, or handling of either defective parts or
replacement parts. SUCH COSTS MAY BE COVERED BY a separate warranty provided by the installer.
LIMITATIONS OF WARRANTIES—ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED
WARRANTY IS GIVEN. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND
MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON
WHATSOEVER.
CARRIER WILL NOT BE RESPONSIBLE FOR:
1. Normal maintenance as outlined in the installation and servicing instructions or owner’s manual.
2. Damage or repairs required as a consequence of faulty installation or application by others.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other damages due to the
inadequacy or interruption of electrical service.

570-212
69-2265EFS—01 M.S. 11-08
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Limited Five-Year Warranty
4. Damage or repairs needed as a consequence of any misapplication, abuse, improper servicing,
unauthorized alteration, or improper operations.
5. Damage as a result of floods, winds, fires, lightning, accidents, corrosive atmosphere, or other conditions
beyond the control of CARRIER CORPORATION.
6. Parts not supplied or designated by CARRIER CORPORATION.
7. CARRIER CORPORATION products installed outside the continental U.S.A., Alaska, Hawaii, and Canada.
8. Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever including
additional or unusual use of supplemental heat.
9. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE
WHATSOEVER. Some states do not allow the exclusion of incidental or consequential damages, so the
above limitation may not apply to you.
Model No. Unit Serial No.
Date of Installation Installed by
Name of Owner Address of Installation