Totally Wicked Buzz User manual

USER MANUAL BEDIENUNGSANLEITUNG

CONGRATULATIONS ON PURCHASING YOUR
TOTALLY WICKED BUZZ
ELECTRONIC CIGARETTE KIT

3
Using your Buzz Kit
510 Connector
Power Button
OLED Display
Adjustment Buttons
Micro-USB Port
Battery Cover

4
Mouthpiece
Top Cap
Glass Tube
Atomizer Head
Atomizer Base

5
Using your Buzz Kit
Installing an 18650 battery:
To insert the battery, turn the Buzz
body upside down, locate the
battery door and use a finger to slide
open the battery door to release
it from the locking mechanism.
Insert the battery into the battery
compartment ensuring the battery’s
positive connection is inserted first.
Finally, push the battery door closed
then slide to lock, ensure the battery
door is fully locked into place.
Note: Ensure only a high drain cell
with a continual discharge rate of
25 amperes or above is installed
into the Buzz kit. Do not use any
batteries that have torn battery
wraps.

6
Using your Buzz Kit
Powering On and Off:
The Buzz kit uses a 5 click on/off
function. To switch the Buzz on,
press the power button five times in
quick succession, the OLED display
will illuminate to indicate the Buzz
has been switched on. Similarly,
when the device is powered on,
press the power button five times in
quick succession to turn the Buzz
off, the OLED display will deactivate
to indicate the Buzz has been
switched off.
Charging the Battery:
The Buzz is recharged by inserting
the micro USB cable into the micro
USB port located directly beneath
the left and right adjustment buttons,
insert the other end of the USB cable
into a powered USB port or suitable
USB wall adaptor. The battery status
symbol on the OLED display will
initially flash to indicate charging
activity, the battery status symbol
will then rise and fall while charging.
Once fully charged, the OLED
display will deactivate. Charging with

7
Using your Buzz Kit
a QC2.0 Wall Adaptor will be around
30% faster than charging with a
standard 1.0A USB adaptor.
Alternatively, the 18650 battery
can be removed from the Buzz
and charged in an external battery
charger.
Installing/Replacing an Atomizer
Head:
To install a new atomizer head, turn
the Hornet tank upside down so the
mouthpiece points toward the floor,
hold the Hornet tank firmly, then
unscrew the base to fully dismantle
the tank. Place the upper section
of the tank to one side, ensuring it
remains upside down to prevent fluid
spillage. Unscrew the atomizer head
from the tank base. Screw the new
atomizer head into the tank base,
and reassemble the tank using the
reverse of the above procedure.

8
Note: Be sure to “prime” the
atomizer head before first use by
dripping in a few drops of e-liquid,
then allowing it to sit in a tank
full of E-liquid for a few minutes
before vaping. This ensures the
atomizer head is fully saturated
with E-liquid.
Using your Buzz Kit

9
Using your Buzz Kit
Filling with E-liquid:
To fill the Hornet tank, locate for
the fill symbol located on top of the
Hornet tank, grasp the mouthpiece
firmly and push/slide in the direction
pictured below to open the tank.
The entire hinged top cap assembly
will open up to reveal two E-liquid
fill holes. Carefully fill the Hornet
tank with E-liquid until the tank is
full. Take care to avoid filling down
the large, central chimney hole, only
fill with E-liquid using either of the
designated fill holes located either
side of the central chimney hole.
Once filled with E-liquid, close the
hinged top cap assembly then firmly
slide it shut in the opposite direction,
an audible click will be heard once
the locking mechanism is fully
engaged.

10
Using your Buzz Kit
Hornet Tank Airflow Adjustment:
To adjust the amount of airflow
the Hornet tank provides, slowly
rotate the airflow control ring on the
atomizer base to expose the desired
proportion of the airflow slot.