Totally Wicked PENGUIN User manual

USER MANUAL / BEDIENUNGSANLEITUNG

CONGRATULATIONS ON PURCHASING YOUR
TOTALLY WICKED PENGUIN
ELECTRONIC CIGARETTE KIT.

3
The Totally Wicked Penguin
Mouthpiece
Airflow Inlet
Power Button
Indicator Lights
Micro-USB Port
Penguin Battery
Mouthpiece
Sleeve

4
Filling with E-liquid:
To fill, grasp the mouthpiece firmly
and pull the atopack assembly
loose from main body, place the
main body to one side. Take hold
of the atopack assembly and rotate
it upside down, use a finger to pry
the white ceramic atomizer from the
atopack assembly. Carefully fill with
E-liquid down the central, oblong
refill hole, avoid the airflow opening
to the side. Once filled, reinsert
the ceramic atomizer back into the
atopack assembly, then reinsert the
entire atopack assembly back into
the main body.
Note: Be sure to “prime” the
atomizer head by allowing it to
sit in a tank full of E-liquid for
five minutes before vaping, this
ensures the atomizer head is fully
saturated with E-liquid.
Using your Penguin

5
Using your Penguin
Atopack Ceramic
atomizer
Filling
hole

6
Using your Penguin
Power On and Off:
To switch the Penguin on, press
the power button five times in quick
succession, the indicator lights will
flash five times to show the Penguin
has been switched on. Similarly,
when the device is powered on,
press the power button five times in
quick succession to turn the Penguin
off, the indicator lights will flash five
times to show the Penguin has been
switched off.
Vaping:
Press and hold the power button as
you inhale the vapour, five indicator
lights will illuminate while the device
is being vaped.

7
Using your Penguin
Charging the Battery:
The Penguin is recharged by
inserting the micro USB cable into
the micro USB port located beneath
the power button, insert the other
end of the USB cable into a powered
USB port or suitable USB adaptor.
The indicator lights will initially flash
five times simultaneously when the
charge lead is first inserted, then
repeatedly flash in sequence until
the battery is fully charged. Once
fully charged, the indicator lights will
turn off completely. Charging with a
QC2.0 Wall Adaptor will be around
30% faster than charging with a
standard 1.0A USB adaptor.

8
Installing/Replacing an Atomizer
Head:
To install a new atomizer head,
grasp the mouthpiece firmly and
pull the entire atopack assembly
loose from main body, place the
main body to one side. Take hold of
the atopack assembly and rotate it
upside down, then, use a finger to
pry the ceramic atomizer head from
the atopack assembly. Dispose of
the old atomizer head then insert a
brand new atomizer head into the
atopack assembly. Then, reinsert the
entire atopack assembly back into
the main body.
Note: Be sure let the new atomizer
head sit in a tank full of E-liquid
for five minutes before vaping to
ensure the atomizer head is fully
saturated with E-liquid.
Using your Penguin

9
Battery Charge Level Light Condition
90 – 100%
70 – 89%
30 – 69%
10 – 29%
0 – 9%
Using your Penguin
Battery Life Indication:
As the level of charge changes the number of indicator lights which are
illuminated will change. The table below can be used as a reference.

10
Using your Penguin
Short Circuit Protection:
If an atomizer short circuit occurs
before the power button is pressed,
the indicator lights will flash five
times in succession. If an atomizer
short circuit occurs while the power
button is pressed, the indicator lights
will flash three times in succession.
Atomizer Protection:
If the power button is pressed
for longer than ten seconds, the
Penguin will cease to function and
the indicator lights will flash ten
times.
Low Voltage Protection:
When the battery voltage drops
below 3.3V, the indicator lights will
flash forty times and the device will
power off. Charge the device via
USB to resume normal operation.