Totally Wicked Corsa Micro User manual

ELECTRONIC CIGARETTE KIT
USER MANUAL / BEDIENUNGSANLEITUNG
TW_Corsa_Micro_Kit_Compliant_Manual.indd 1 22/03/2017 12:44

2
Congratulations on purchasing your
Totally Wicked Corsa Micro Electronic Cigarette.
The Totally Wicked Corsa Micro is an exceptionally compact, yet highly functional
device incorporating an intelligent temperature control system, allowing you to
finely tune to suit your vaping style. Additionally, upgradeable firmware means that
you will always be up to date. Paired with the Corsa Micro is the Corsair Mini Pro
Tank, providing a reliable leak resistant design, top filling capability and adjustable
airflow. The user is provided with six modes of vaping operation; Variable Power
(W); Bypass; Variable Temperature with Nickel Coils (Ni); Variable Temperature
with Titanium Coils (Ti); Variable Temperature with Stainless Steel Coils (SS316)
and Temperature Coefficient of Resistance (TCR). The adjustable modes allow for
incremental settings in terms of watts or temperature. Additionally, the Corsa Micro
also includes both custom logo and adjustable date and time display functions.
This device combines all of its functionality and 1500mAh battery in a sleek and
ergonomic, yet simple to use package.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 2 22/03/2017 12:44

3
Firmware Upgrade: To
upgrade the firmware
installed on the device
simply load the relevant
product page on the Totally
Wicked website, click on
the link under ‘Firmware
Upgrade’ and follow the
instructions provided.
Corsa Micro Battery
510 Thread and
Sprung Connector
Power Button
OLED Screen
Micro
USB Port
Reset Button
Adjustment Buttons
TW_Corsa_Micro_Kit_Compliant_Manual.indd 3 22/03/2017 12:44

4
Mouthpiece
Mouthpiece Base
Atomizer Base
Airflow Ring
Atomizer Head
Atomizer Tube
Corsair Mini Pro Tank
TW_Corsa_Micro_Kit_Compliant_Manual.indd 4 22/03/2017 12:44

5
Using your Corsa Micro Kit
Using your Tank for the First Time:
Remove the atomizer base from
the tank and drip a few drops of
e-liquid into the atomizer head, this
will ensure optimum operation and
longevity of the atomizer. Refit the
atomizer base before filling the tank.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 5 22/03/2017 12:44

6
Using your Corsa Micro Kit
Filling the Corsair Mini Pro Tank:
To fill the tank, turn the mouthpiece
base in the anticlockwise direction
until it is fully removed from the tank.
Insert the e-liquid into one of the two
fluid filling slots, being careful not to
overfill the tank. Refit the mouthpiece
base firmly. The Corsair Mini Pro Tank
can now be installed onto the Corsa
Micro by turning in the clockwise
direction until firmly seated.
Maximum refill nozzle diameter:
16.0mm
TW_Corsa_Micro_Kit_Compliant_Manual.indd 6 22/03/2017 12:44

7
Using your Corsa Micro Kit
Power On and Off:
The Corsa Micro uses a 5-click on/
off function. To switch the device on,
press the power button 5 times in
quick succession. The OLED screen
will illuminate, signifying that the
device is powered on. If the Corsa
Micro is powered on the user can
press the button 5 times to switch the
device off.
Vaping:
Simply press the power button as
you inhale.
Adjusting the Airflow:
To adjust the airflow, simply twist
the airflow ring in the clockwise
direction to loosen the draw and in
the anticlockwise direction to tighten
the draw.
Adjusting the Fluid Flow (LVC
Atomizer Head):
When an LVC (Liquid Valve Control)
atomizer head is installed, turn the
ring at the base of the atomizer to
regulate the amount of fluid which
can enter the atomizer wick.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 7 22/03/2017 12:44

8
Using your Corsa Micro Kit
New Atomizer Installation:
When a new atomizer is connected,
or the existing atomizer is
disconnected and reconnected, a
message prompt may be displayed
– ‘New Coil Right, Same Coil Left’.
Press the right adjustment button to
confirm that a new atomizer has been
connected, or the left adjustment
button to confirm that the existing
atomizer has been reconnected.
Selection of a new coil should only
be made when the atomizer and coil
are at room temperature.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 8 22/03/2017 12:44

9
Using your Corsa Micro Kit
Charging the Battery:
Charge the Corsa Micro via the USB
cable when connected to a powered
USB port or suitable wall adapter.
The indicator on the display will
indicate the battery status.
Battery Charge:
The battery charge for the internal
battery is displayed on the fifth row of
the OLED display.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 9 22/03/2017 12:44

10
Using your Corsa Micro Kit
Shift between VW/Bypass/VT/TCR/
Clock Modes:
When powered on, press the power
button 3 times consecutively, the first
row will flash, use the right adjustment
button to cycle through the VW/
Bypass/VT/TCR/Clock modes.
VW Mode:
When in VW mode, use the right or
left adjustment buttons to increase
or decrease the level of wattage
respectively. The available wattage
range is 1W – 40W in increments
of 1W.
Bypass Mode:
When in bypass mode there is
a direct output of the voltage of
the internal battery cell. The cells
operating voltage will be displayed
when the power button is pressed,
and will be dependent on the
resistance of the atomizer used.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 10 22/03/2017 12:44

11
Using your Corsa Micro Kit
VT Mode (Ni/Ti/SS316):
To shift between Ni/Ti/SS316: when
in VT mode press the power button
3 times consecutively; the first row
will flash; press the left adjustment
button and the Ni/Ti/SS316 symbol
will flash; then use the right
adjustment button to shift between
the Ni/Ti/SS316 modes. When in VT
mode, use the right or left adjustment
buttons to increase or decrease
the temperature respectively. The
available temperature range is
100-315°C or 200-600°F and can
be adjusted in increments of 5°C
and 10°F. To adjust the wattage
level whilst in VT mode: press the
power button 3 times consecutively
to activate the menu; press the left
adjustment button twice and the
wattage (PWR) value will flash; use
the right adjustment button to adjust
the wattage level. To lock/unlock the
atomizer resistance: press the power
button 3 times in quick succession
to activate the menu; press the left
adjustment button three times and
the atomizer value will flash; use the
right adjustment button the lock/
unlock the atomizer resistance.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 11 22/03/2017 12:44

12
Using your Corsa Micro Kit
Note: Only lock the atomizer when
the coil is at room temperature.
Note: If a coil with a resistance
exceeding 1.5ohms is applied in VT
mode, the device will automatically
switch to VW mode. Also, if a
standard kanthal coil is used
under VT mode, the device will
automatically switch to VW mode.
TCR Mode:
When in TCR mode and the title is
flashing indicating that the menu
is active, press the left adjustment
button once and the sub-menu (M1,
M2 and M3) will flash. Whilst the
sub-menu is flashing press the right
button to shift between M1, M2 and
M3, then press the power button to
confirm. (Also see: Configuring TCR
Mode)
TW_Corsa_Micro_Kit_Compliant_Manual.indd 12 22/03/2017 12:44

13
Using your Corsa Micro Kit
Configuring TCR Mode:
To set the temperature coefficient
of resistance to match a particular
coil, ensure the device is powered
off, then simultaneously hold
the power button and the right
adjustment button to enter the TCR
configuration menu. Use the right
or left adjustment buttons to select
which to configure from M1, M2 and
M3 – this feature allows the TCR
values for 3 materials to be stored to
the device. Press the power button
to select the TCR value and then use
the right and left adjustment buttons
to increase or decrease the value
to your preference, long press the
power button or leave the device for
10 seconds to confirm the selection.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 13 22/03/2017 12:44

14
Using your Corsa Micro Kit
Material TCR Value Range
Nickel 600-700
NiFe 300-400
Titanium 300-400
SS (303, 304, 316, 317) 80-200
TCR Value Range:
Note: The TCR value displayed is 105(100,000) times greater than the actual
TCR value and is for Corsa Micro usage only.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 14 22/03/2017 12:44

15
Material TCR Value Range
Nickel 600-700
NiFe 300-400
Titanium 300-400
SS (303, 304, 316, 317) 80-200
Using your Corsa Micro Kit
Shift Between Clock Modes:
Two clock display modes are
available, dial and numerical. When
the clock display is active, press the
power button 3 times consecutively
to activate the menu. Press the
left adjustment button once and
the second row will flash. Use the
right adjustment button to alternate
between the dial and numerical
display options. Press the power
button to confirm the selection.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 15 22/03/2017 12:44

16
Using your Corsa Micro Kit
Time/Date Adjustment:
To adjust the time/date values,
ensure that the device is in the
numerical clock mode and press
the power button 3 times to enter
the menu, press the left adjustment
button once and the date values
will flash, press the left adjustment
button to cycle through Hour/Minute/
Year/Month/Day and use the right
adjustment button to adjust the
selected parameter. Note: Only the
year parameter can be reversed by
pressing the left adjustment button
whilst adjusting.
Current/Puff Count/Puff Duration
Display:
The real-time current (AMP)/puff
count/puff duration is displayed on
the screen on the fourth row. To
shift between each mode, press the
power button 3 times consecutively
to activate the menu, press the left
adjustment button until the current/
puff count/puff duration flashes, use
the right adjustment button to cycle
through the modes.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 16 22/03/2017 12:44

17
Using your Corsa Micro Kit
Active Screen Duration/
Screensaver Adjustment:
When the device is powered on,
simultaneously hold the right
adjustment button and the power
button to enter the active screen
duration adjustment menu, use
the left adjustment button to cycle
through the options and press the
power button to confirm the desired
time or to turn off the screensaver.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 17 22/03/2017 12:44

18
Using your Corsa Micro Kit
Custom Logo Mode:
To add a custom logo to the device,
open the ‘Firmware Update’ software
as described in ‘Updating Firmware’.
Click on the ‘LOGO’ icon and select
the 64 x 40 BMP image file you would
like to upload. To activate/deactivate
logo mode, simultaneously hold the
power button and right adjustment
button to activate the active screen
adjustment menu, press the right
adjustment button once and logo
mode will be displayed, use the
left adjustment button to select On/
Off and press the power button to
confirm the selection.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 18 22/03/2017 12:44

19
Using your Corsa Micro Kit
Resetting the Device:
To reset the device to default
settings, hold the up adjustment
button and press the reset button
using a pin. This may be required if a
firmware update does not succeed.
Stealth Mode:
When powered on, simultaneously
hold the power button and the
left adjustment button to activate
stealth mode. Repeat the process to
deactivate stealth mode.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 19 22/03/2017 12:44

20
Using your Corsa Micro Kit
Charge Error:
If no charging current is detected
when the device is connected to the
charging lead, ‘Charge Error’ will be
displayed. Please contact customer
services.
Temperature Protection:
When in VT mode, if the actual
temperature of the coil is above the
set temperature then ‘Protection’ will
be displayed on the screen. This is
normal operation of the device and
the user may continue to vape.
TW_Corsa_Micro_Kit_Compliant_Manual.indd 20 22/03/2017 12:44