Totally Wicked AURA User manual

USER MANUAL

TOTALLY WICKED
AURA
ELECTRONIC
CIGARETTE KIT.
CONGRATULATIONS
ON PURCHASING YOUR

3
Tank
connection
Power
button
UP
adjustment
button
DOWN
adjustment
button
AURA BATTERY CS AURA TANK
Mouthpiece
Glass
section
Airflow
control ring
Atomizer
head
Tank
base
LED
screen
USB
charging
port

4
AURA QUICK START GUIDE
If you are familiar with using e-cigarettes, follow the quick start guide
below to get vaping in minutes:
• Prime the atomizer head.
• Fill the tank.
• Switch the Aura on (5 clicks of the power button).
• Set the Aura to 12 watts.
• Press the power button and inhale
• Charge the battery (possibly not shipped with a full charge).
Detailed descriptions of these steps and more are given in the full user guide below.

5
Priming the Atomizer Head
Remove the tank from the Aura battery by
unscrewing at the tank base. Turn the tank
upside down, then unscrew the tank base
from the glass section of the tank. Prime
the atomizer head by dripping a few drops
of e-liquid into its central hole.
USING YOUR AURA - PRIMING

6
USING YOUR AURA - FILLING
Filling the Tank
Fill the tank through one of the apertures
either side of the central air hole. Do not
allow any e-liquid to enter the central air
hole. Once filled, screw the tank base back
onto the glass section of the tank then fit
the tank back onto the Aura battery.
Note: After priming a new atomizer head
and filling the tank, it is recommended to
wait 5 minutes before vaping to ensure the
atomizer head is fully saturated.

7
Atomizer Head Lifespan
Atomizer heads do not last forever and
need to be periodically replaced. Time
in use before replacement is required
is generally from a few days to several
weeks, depending on power used, vaping
style, flavour and type of e-liquid used. A
slight burnt taste, general loss of vapour
production or a reduction in flavour
intensity can all be indicators that the
atomizer head requires replacement.
Powering On and Off
Switch the Aura on by quickly pressing
the power button five times, the screen
will activate indicating the Aura has been
switched on. Quickly pressing the power
button five times will switch the Aura off, the
screen will deactivate indicating the Aura
has been switched off.
USING YOUR AURA

8
USING YOUR AURA - SETTING THE CORRECT WATTAGE
The wattage on the Aura battery is
adjustable and can be set from 1-30 watts.
The wattage is set to 30W out of the box,
we recommend reducing the wattage to
12W to prevent the atomizer head from
burning prematurely. To set the correct
wattage, ensure the Aura is switched on;
then keep pressing the down adjustment
button until the screen reads 12W. Lower
wattage settings produce cooler, less
dense vapour: but setting the wattage too
low will produce little, if any vapour. Higher
wattage settings produce larger clouds of
vapour, but setting the wattage too high
can lead to poor flavour; or even a burnt
taste in the vapour. Experiment to find your
own favourite setting, which will generally
be between 7W and 15W.
Tip: Press and hold down either of the
adjustment buttons to make speedy
changes to the wattage.
Vaping
Press and hold the power button as you
inhale the vapour, the screen will display
a vape timer while the power button is
held down.

9
Adjusting Airflow
If you find the air flow
too airy or too tight
while vaping, rotate the
airflow control ring on
the base of the tank.
Exposing more holes
will provide more air
flow while exposing
fewer holes will restrict
the air flow. Experiment
to find your preference.
E-liquid Level
To prevent the atomizer head from
becoming dry and burning prematurely,
ensure the e-liquid level does not drop
below the bottom of the glass section of
the tank.
USING YOUR AURA

10
USING YOUR AURA
Atomizer Head Protection
If the power button is held down for longer
than 10 seconds while vaping, the screen
will display “OVER 10S” and the Aura will
refuse to power or produce any vapour.
Releasing the power button will allow
normal operation to resume.
Charging the Battery
The Aura is charged by connecting the
charge port on the battery to a USB port
or suitable wall adaptor with the supplied
charging lead. The screen will activate
when the charge lead is first connected,
and display an animated battery icon while
charging. Once the battery is fully charged
the screen will switch off.