Totally Wicked aio Slider Hellfire User manual

USER MANUAL / BEDIENUNGSANLEITUNG

2
Congratulations on purchasing your
Totally Wicked aio Slider Hellre Electronic Cigarette Kit.
The Totally Wicked AIO Slider Hellfire is an all-in-one device that combines
optimum ease of use with exceptional vapour production. This is made possible
by the combination of HW atomizer heads and a considerable maximum power
output of up 50 Watts. 2 x 0.2ohm HW1 single cylinder, dual coil atomizer heads
are supplied. HW2 0.3ohm dual cylinder quad coil, HW3 0.2ohm triple cylinder
sextuple coil and HW4 0.2ohm quad cylinder octuple coil atomizer heads are
available separately as optional atomizer heads. The slide to fill mechanism
incorporated into the top cap of the device, single button functionality, and direct
voltage output ensure that the device is extremely simple to use, whilst providing
a satisfying vape at a moment’s notice. In addition, a substantial 3000mAh battery
is integrated into the surprisingly compact device housing, which is sure to supply
power for plenty of time between recharges.

3
Power Button
Battery
Atomizer Base
Airflow Ring
HW Coil
Glass Tube
Top Cap
Mouthpiece

4
Using your aio Slider Hellre
Power On and Off:
To switch the AIO Slider Hellfire on,
quickly press the power button 5
times, the power button LED will
illuminate to indicate that the device
has been switched on. Similarly,
when the device is powered on,
quickly press the power button 5
times to switch the device off.
Vaping:
Simply press the power button as
you inhale, the power buttons LED
will illuminate while the device is
powered.
Charging the Battery:
The AIO Slider Hellfire can be
charged via the USB cable when
connected to a powered USB port
or suitable wall adapter. The USB
port LED will illuminate in red to
indicate that the battery is charging
successfully, the light will turn off
once fully charged.

5
Installing/Replacing an Atomizer
Head:
Firstly, ensure the tank is completely
empty of e-liquid to prevent e-liquid
leakage. To replace the atomizer
head, unscrew the top cap from the
atomizer by turning it anti-clockwise
until the top cap fully detaches,
then the glass must be removed
by carefully pulling it upwards.
Remove the existing atomizer head
by unscrewing it in an anti-clockwise
direction until it fully detaches. The
new atomizer head can now be fitted
into the atomizer base by screwing
it in a clockwise direction until firmly
sealed. Refit the glass and replace
the top cap by screwing it in a
clockwise direction,
ensuring they are
firmly sealed before
filling.
Using your aio Slider Hellre
Note: Be sure to
drip a few drops
of e-liquid into the
atomizer head before
the first usage to
ensure maximum
performance.

6
Filling with E-liquid:
To fill the device, slide the upper
section of the top cap to the side
by pushing firmly sideways, this will
expose the filling hole. The correct
sliding direction is clearly indicated.
Insert the e-liquid filling nozzle into
the fill hole and slowly fill the tank
with e-liquid, being careful not to
overfill.
Note: When filling, ensure that the
tank is not entirely filled and an
air gap of 2mm remains above the
e-liquid to ensure proper e-liquid
supply to the wick.
Using your aio Slider Hellre
Sliding Cap

7
Adjustment of Airflow:
To adjust the airflow through the
atomizer, simply turn the airflow ring
on the atomizer base to expose the
desired area of the airflow slot.
Using your aio Slider Hellre

8
Battery Life Indication:
As the level of charge changes the
LED will change colour. The table
below can be used as a reference.
Using your aio Slider Hellre
Battery Charge Level Light Colour
60 – 100% Green
30 – 59% Orange
10 – 29% Blue
0 – 9% Red

9
Using your aio Slider Hellre
Short Circuit Protection:
If a short circuit occurs before
the power button is pressed, the
power buttons LED will flash 5
times consecutively. If a short circuit
occurs while the power button is
pressed, the power buttons LED will
flash 3 times consecutively.
Atomizer Protection:
If the power button is held down for
longer than 15 seconds, the device
will stop producing any vapour and
the power buttons LED will flash
10 times.
Low Voltage Protection:
When the battery voltage drops
below 3.3V, the power buttons LED
will flash 40 times and the device
will power off. Charge the device via
USB to power it back on.

10
Kit Contents
1 x AIO Slider Hellfire
2 x 0.2ohm HW1 Single Cylinder, Dual Coil Atomizer Heads (1 Fitted, 1 Spare)
1 x Mouthpiece
1 x Sealing Rings
1 x USB Cable
1 x User Manual