Totally Wicked Curve VT60 User manual

USER MANUAL

2
Congratulations on purchasing your new
Curve VT60 electronic cigarette kit.
The Curve VT60 combines the latest innovation in variable temperature (VT) vaping
with the incredibly stylish and popular Curve range of Totally Wicked’s electronic
cigarettes. The enormous popularity of the Curve range is founded in ultimate
practicality and ergonomic designs which allow the excellent functionality to be
experienced and loved by all, from completely new users to the most advanced and
experienced vapers. The addition of a temperature control system further enhances
the practicality of the device, allowing a user to tune the device to suit their vaping
style and doing so with a respectable power output of 60 Watts. The Curve VT60
includes the provision to use variable temperature mode with Nickel 200 and Titanium
coils, or can simply be used as a variable wattage device with Kanthal or NiChrome
coils. Conveniently, the 18650 battery included with the device is removable due to the
interchangeable front and back magnetic covers. We are sure the Totally Wicked Curve
VT60 will represent a very important stepping stone in our product history.

3
The Curve VT60
A. Spring stainless steel 510
connector
B. Power button
C. OLED screen
D. Up/Down rocker button
E. Mode button
F. Front cover (decorative)
G. Back cover (battery access)
H. Micro USB cable port (1.0amp)
Sub-Air ll Tank
I. Atomizer base
J. Air-flow control
K. ML atomizer head
L. Atomizer tube
M. Side e-liquid filling hole
N. Mouthpiece
A
B
C
D
E
F
G
M
IJ
KL
N
H

4
Priming a new atomizer head:
Unscrew the atomizer base (a) from the atomizer tube. Ensure the atomizer head
(c) is firmly screwed into the base. Add a small amount of e-liquid into the top of the
atomizer head and one drop of e-liquid to the 4 small wicking holes on the side of the
atomizer head. Refit the base to the atomizer tube and fit the mouthpiece (f).
Filling the tank:
Ensure the air-flow control (b) is fully closed, fully open the e-liquid filling hole (e) whilst
holding the tank at 45° carefully fill the tank until the level of e-liquid reaches the top of
the glass tube. Close the filling hole and open the air-flow control.
Note: Colour coded seals to match the atomizer head are provided to fit to the tank as
a reminder of which type of atomizer head you have installed.
The tank is ready to be fitted to the Curve VT60.

5
Fitting the battery to the Curve VT60:
Remove the back magnetic cover (G). Install an appropriately specified 18650 mAh
battery ensuring the polarity of the battery matches the polarity of the markings inside
the device. Refit the back cover.
Power on and off:
Press the power button (B) 5 times in quick succession, the OLED Screen will light
to indicate the Curve VT60 is on and ready to use. In the same way, to turn the Curve
VT60 off, press the power button 5 times in quick succession. When the Curve VT60
is on, the screen will turn off after 30 seconds of inactivity, but will seamlessly recover
when the power button is pressed.

6
Using your Curve VT60
Vaping in Temperature Mode:
Press the power button as you inhale. When the button is held down, the OLED
screen will be illuminated, and will show the temperature, power and base atomizer
resistance.
Vaping in Power Mode:
Press the power button as you inhale. When the button is held down, the OLED screen
will be illuminated and will show the power, voltage, resistance and vaping time.
Temperature Protection:
In Temperature Control-Ni and Ti mode, if the actual temperature of the coil exceeds
the user set temperature, the screen will show “Temp Protection”. This is normal and
shows the device is operating correctly.

7
Adjusting temperature:
Target coil temperature is adjusted by pressing the up or down rocker button (D).
Press and hold either button to make large changes. Sweeping to either extreme of
the adjustment range will switch display from Fahrenheit (200°- 600°) to Celsius (100°-
315°) and vice versa.
(D)
(D)

8
Adjusting atomizer airflow:
Adjusting the airflow control (b) varies the aperture size through which air is drawn
into the atomizer. This can be adjusted to give the perfect resistance to airflow to suit
your taste.
Adjustment Lock function:
While the device is on, simultaneously hold the up and down rocker button for 2
seconds until “Lock” appears on the OLED screen. If the adjustment lock is active
the output adjuster buttons will not function, preventing accidental VT/VW setting
adjustments. The lock can be disabled in the same way, and “Unlock” will be
displayed.

9
Lock/Unlock atomizer resistance:
With the Curve VT60 in Ni or Ti Temperature control mode, press the power button
(B) and the up button together for 2 seconds to lock the atomizer resistance at “base
resistance”. A padlock icon will appear next to the resistance reading. Repeat the
above to unlock the resistance and a “Ω” symbol will appear next to the resistance
reading. (Note: Please lock the resistance only at room temperature so that the Curve
VT60 can record the correct “base resistance”.)
In the unlocked mode, when you change the atomizer, the screen may display “New
coil up - same down”. If the same coil is still fitted, press the down button, and if it is a
new coil press the up button. Please unlock the resistance when fitting a new atomizer/
coil of a different resistance.
(B) (UP) (DOWN)

10
Display rotation:
While the device is off, simultaneously hold the up and down buttons for 2 seconds to
rotate the display orientation through 180 degrees.
(UP)
(DOWN)