Totally Wicked DI6 User manual

USER MANUAL/ BEDIENUNGSANLEITUNG

CONGRATULATIONS
ON PURCHASING YOUR
TOTALLY WICKED
D16 ELECTRONIC
CIGARETTE
KIT

3
Mouthpiece
D16 Tank
Atomizer
Atomizer Base
Power Button
Battery Body

4
Using your D16 Kit
Filling the D16 Tank with e-liquid:
Grip the base of the D16 tank and
remove the tank from the battery
by unscrewing. Once removed turn
the tank so that the base is at the
top, and unscrew from the tank. Fill
the tank, ensuring that e-liquid is
poured down the side of the central
air tube, and not into the central air
tube. Once filled, reassemble the
tank using the reverse of the above
procedure. Take care not to fill
higher than the white rubber gasket
on the central air tube, as this is the
maximum fill level.
Note: Be sure to “prime” the
atomizer head before first use by
dripping a few drops of e-liquid
into the centre, then allowing it to
sit in a tank full of E-liquid for a
few minutes before vaping. This
ensures the atomizer head is fully
saturated with e-liquid.

5
Using your D16 Kit

6
Powering On and Off:
The D16 kit uses a 5 click on/off
function. To switch the D16 on,
press the power button five times
in quick succession. A white LED
surrounding the power button
will flash 5 times indicating the
D16 battery has been switched
on. Similarly, when the device is
powered on, press the power button
5 times in quick succession to turn
the D16 kit off. The white LED will
flash 5 times indicating the D16 kit
has been switched off.
Installing/Replacing an Atomizer
Head:
To install a new atomizer head,
remove the tank base as described
in “Filling the D16 Tank” above.
The atomizer head is push fit, and
can be removed by simply pulling
free of the base. Ensure that the
replacement atomizer head is snugly
and completely located in the tank
base. This will prevent the atomizer
head from falling out when refilling
with e-liquid.
Using your D16 Kit

7
Using your D16 Kit

8
Charging the Battery:
The D16 battery is recharged by
inserting the micro USB cable into
the micro USB port situated to the
left of the vape button. Insert the
other end of the USB cable into a
powered USB port or suitable USB
wall adaptor. The white LED will flash
5 times to indicate charging has
commenced, and a red LED light
will remain constant while charging.
Once fully charged the red LED light
will go out.
Vaping:
Press and hold the power button
as you inhale vapour from the
mouthpiece. Release the power
button when you have finished
inhaling.
Using your D16 Kit

9
Using your D16 Kit
Battery Life Indication:
The remaining battery charge is indicated by the illumination of the LED shortly
after the devices power button has been released. The battery’s remaining level
of charge and corresponding light conditions are detailed in the table below.
Battery Level Light Condition
60%-100% Stays lit
30%-59% Flashes Slowly
10%-29% Flashes Moderately
0-9% Flashes Quickly

10
Short Circuit Protection:
If an atomizer short circuit occurs
or the atomizer head’s resistance is
below 0.2ohms, the LED will flash
3 times and the D16 kit will not
produce power or vapour. If the
short circuit warning is displayed,
ensure the atomizer head is properly
seated. If the error message still
occurs replacing the atomizer head
with a brand new one should resume
normal operation.
Incompatible Resistance Warning:
If the atomizer heads resistance
exceeds 5.0ohms, the vape buttons
LED will slowly flash to indicate the
atomizer heads resistance is too
high. If the incompatible resistance
warning is displayed, ensure the
atomizer head is properly fitted.
If properly fitted and the warning
continues, replacing the atomizer
head with a brand new one should
allow normal operation to resume.
Using your D16 Kit