Totevision LCD-2001VB User manual

Page 1
LCD-2001VB
Sunlight Readable 20.1" LCD Display
(1st Edition 11/25/2004 )
All information is subject to change without notice.
○
1319 Dexter Avenue N.#020,
Seattle,WA98109
TEL：[phone]
FAX：[phone]
R

Page 2
Content
Introduction...........................................................................................................3
Hardware Installation............................................................................................3
The Display Timing............................................................................................... 5
The Display Outline Dimensions..........................................................................6
The Display Controls............................................................................................ 7
The Screen Adjustment........................................................................................ 8
Quick Installation &Troubleshooting Tips...........................................................19
Specification........................................................................................................20
Product Safety Precautions................................................................................2221

Page 3
Introduction
Welcome to enjoy the fantastic sightseeing world. This new technology will bring you the whole
new feeling about the “monitor”. We show here some of the major advantages of the LCD
monitor. You will really find some other advantages when you use it.
Hardware Installation
This chapter will guide you the correct installation procedures of your LCD monitor.
Unpacking
After you unpack your LCD Monitor, please make sure that the following items are included in the
carton and in good condition. If you find that any of these items are damaged or missing, please
contact your dealer immediately.
One LCD Monitor
15-pin D-sub VGA cable
AC/DC adapter with 12V DC output & AC power cord
Remote Control
TV Tuner (Option)
Installation
This analog LCD display does not require any special drivers. Necessary drivers are supplied
by the video card manufacturer and may be found on the diskettes supplied with the video card
that came with your computer. Windows 98/2000/XP drivers for both the display and the video
card are supplied on the Windows 98/2000/XP CD or diskettes. Unfortunately, Microsoft did not
provide a complete listing of the displays on the initial retail release. You may use the standard
XGA (1024x768) as the display type. The video card must also be set up correctly in Windows
98/2000/XP and make sure the video output of the VGA card is on list in Section 6.1 or check your
Video Card manual or Windows 98/2000/XP Read me file for further information on Video Card.
After the question listed above is solved, we continue the setup procedure as below.
1. Turn power off both Computer and Display before making any connection.
2. Install Display on the solid horizontal surface such as a table or desk.
3. Connect the power cable and the AC/DC adapter, then connect adapter toe the back of the
LCD monitor.
4. The LCD monitor comes with a 15-pin video cable; you may use this cable for both IBM PC’s
& compatibles and Macintosh.
5. Tighten the screws of the Display cable until the connectors are fastened securely.
6. Switch on power to the Computer system, then to the monitor.

DC Power in
Audio in
AV Audio in
AV in
S-video
VGA
TV Tuner
Page 4
The following picture provides the connection outline
VGA Input Pin Assignment
This section describes the pin assignment of the LCD’s VGA connector. It is called 15pin Mini
D-sub connector.
110 6
11
5
15
Pin No. Signal Connector
1Red Video Signal
2Green Video Signal
3Blue Video Signal
4N.C.
5Ground
6Ground for red video signal
7Ground for green video signal
8Ground for blue video signal
9N.C.
10 Ground
11 N.C.
12 DDC data
13 Horizontal sync signal
14 Vertical sync signal
15 DDC clock

Page 5
The Display Timing
Applicable video timing
The following table lists the better display quality modes that the LCD monitor provides. If the
other video modes are input, the monitor will stop working or display unsatisfactory picture quality.
VESA Modes
Mode Resolution Total Nominal
Frequency
±0.5KHz
Nominal
Frequency
±0.5KHz
Nominal
Pixel Clock
(MHz)
DOS 720x400@70Hz 900x449 31.469 70.087 28.322
640x480@60Hz 800x525 31.469 59.940 25.175
640x480@72Hz 832x520 37.861 72.809 31.500
VGA
640x480@75Hz 840x500 37.500 75.000 31.500
800x600@56Hz 1024x625 35.156 56.250 36.000
800x600@60Hz 1056x628 37.879 60.017 40.000
800x600@72Hz 1040x666 48.077 72.188 50.000
SVGA
800x600@75Hz 1056x625 46.875 75.000 49.500
1024x768@60Hz 1344x804 48.363 60.004 65.000
1024x768@70Hz 1328x806 56.476 70.069 75.000
XGA
1024x768@75Hz 1312x800 60.023 75.029 78.750
IBM Modes
EGA 640x350@70Hz 800x449 31.469 70.086 25.175
DOS 720x400@70Hz 900x449 31.469 70.087 28.322
VGA 640x480@60Hz 800x525 31.469 75.000 31.500
XGA 1024x768@72Hz 1304x798 57.515 72.100 75.000
MAC Modes
VGA 640x480@60Hz 800x525 31.469 59.940 25.175
SVGA 832x624@75Hz 1152x667 49.725 74.551 57.2832
XGA 1024x768@75Hz 1328x804 60.927 74.927 80.000

Page 6
The Display Outline Dimensions
Unit: mm

Page 7
The Display Controls
Control Function
Œ
•
Ž
•
•
‘
’
Power
Power LED :
UpKey:
Menu Key :
Down Key :
Select Key :
Source
Key :
Key :
Channel Up Key:
Channel Down Key :
Power ON/Off.
Power ON-Green / Power Off-No.
Enter the mainmenu of the on-screen display (OSD).
Decrease volume gain when OSD is off.
Input source select (PC,AV, S-Video, TV, Component).
Increase TV channel number.
Decrease TVchannel number.
Increase itemnumber or value of theselecteditem when.
Increase volume gain whenOSD is off.
Decrease itemnumber or item vallue when OSD is on.
Activate the selected icon or function.
“
”
Side Membrane Control Button
Toprevent unauthorized adjustment on OSD menu, LD2011 has a special key lock function.
1. Press"volumeup"&"volumedown" keys simultaneouslyfor 3seconds,the power led
should turn into orange color andblinking for 3 times. The OSD has been locked.
2. Do thesame procedureagain to release the lock.
3. While OSDis locked,youshouldstill be able to change theOSD with yourremotecontroller.
OSD KeyLock Function

Page 8
The Screen Adjustment
Main Menu
You can adjust the brightness, contrast, display colors, the horizontal and vertical position of the
display and OSD menu, etc. through the main menu display.
The Down Key < and Up Key >are used to scroll through items within the menu. The selected
item is highlighted as the scrolling move along. The SELECT key is used to activate the
highlighted item. During this state, MENU key is used to close the OSD menu from the screen.

OSD Control Key
Power key :Power ON/OFF.
Menu key :Enter the main menu of the on-screen display (OSD).
Down key :Decrease item number or item value when OSD is on.
Decrease volume gain when OSD is off.
Up key :Increase item number or value of the selected item when .
Increase volume gain when OSD is off.
Select key :Activate the selected icon or function.
Source key :Input source select (PC, AV, S-Video ,TV, Component).
Channel up key :Increase TV channel number.
Channel down key :Decrease TV channel number.
Page 9
The Screen Adjustment

OSD Control Function List
◆OSD For PC input
Page 10
The Screen Adjustment

the adjustment, press “Menu” again to go back to previous menu.
Picture Adjust This item can adjust Auto Adjust, Brightness, Contrast, Pixel
Clock, Phase, H-Position and V-Position for an optimal image.
Color This item can select 9300/6500 color temperature or adjust
USER color.
Audio This item can adjust audio function, as Volume, Mute, Treble,
Base, Balance.
PIP This item can control Picture in Picture (PIP) function.As
picture sub source, audio source, sub source SIZE, H-Position,
V-Position, and change sub picture color setting.
SYSTEM This item can Select Source input (PC, AV, S-Video, TV,
Component.) and Recall System data.
OSD This item can control OSD window function.As OSD H-Position,
OSD V-Position, OSD Transparence and OSD Off time.
LANGUAGE This item can Select Language (English or Tradition Chinese).
zPicture Adjust
Auto Adjust Automatically adjusts H-Position, V-Position, Pixel
Clock and Phase for an optimal image.
Press “Select” to execute.
Brightness Adjusts the Brightness.
Press “Up” or “Down“ to adjust the parameter.
Contrast Adjusts the difference between the light and dark areas.
Press “Up” or “Down“ to adjust the parameter.
Clock Adjusts the video distortion. It will appear horizontal
noise on the screen while adjust the Clock.
Press “Up” or “Down“ to adjust the parameter.
Phase Adjusts the video distortion. It will appear vertical noise
Page 11
The Screen Adjustment
zMain Menu
Press “Up” or “Down” to locate the item you desire to change, then press “Select” to make

Press “Up” or “Down“ to adjust the parameter.
Horizontal Position Moves the display picture.
Press “Up” to the right or press “Down“ to the left.
Vertical Position Moves the display picture.
Press “Up” to the up or press “Down“ to the down.
zColor
9300K Select 9300 color temperature
Press “Select” to execute.
6500K Select 6500 color temperature
Press “Select” to execute.
User Select USER color temperature
Press “Select” to execute.
Red Adjust gain of the Red color
Press “Up” or “Down“ to adjust the parameter.
Green Adjust gain of the Green color
Press “Up” or “Down“ to adjust the parameter.
Blue Adjust gain of the Blue color
Press “Up” or “Down“ to adjust the parameter.
Page 12
The Screen Adjustment

 Audio
Volume Adjust Volume gain
Press “Up” to increase or press “Down“ to decrease.
Mute Set Audio mute.
Press “Up” to execute mute or Press “Down“ to release
mute.
Treble Adjust audio Treble .
Press “Up” to increase or press “Down“ to decrease.
Bass Adjust audio bass .
Press “Up” to increase or press “Down“ to decrease.
Balance Input source select.
Press “Up” to right or press “Down“ to left.
Page 13
The Screen Adjustment

 PIP
Sub Source This item can select sub source (Off, AV, S-Video, TV, and
Component)
Press “Select” to execute..
Audio Select audio come from Main Source or Sub Source.
Press “Up” to come form Main Source
Press “Down” to come form Sub Source.
Size Change the Sub Picture Size.
It supports 4 step size( 0% ,33% ,66%, 100%)
Press “Up “ to enlarge the sub picture
Press “Down” to reduce the sub picture.
H-Position Moves the Sub Picture.
Press “Up” to the right or press “Down“ to the left.
V-Position Moves the Sub Picture.
Page 14
The Screen Adjustment

Press “Up” to the up or press “Down“ to the down.
PIP Color Change the Sub Picture color setting.
Press “Select” to execute.
Five items can be adjusted in PIP color function
Brightness: Adjusts the sub picture brightness.
Contrast: Adjusts the sub picture contrast.
Saturation: Between colorful and colorless.
Hue: Color varying
Sharpness: Adjusts the Sharpness.
Press “Up” to increase or press “Down“ to decrease.
 System
Recall Restore the default value.(The value according to the
factory mode)
Press “Select” to execute.
Source Input source select. (PC, AV, S-Video, TV, Component)
Press “Select” to execute..
 OSD
OSD H-Position Adjusts the OSD position left or right
Press “Up” to right, press “Down“ to left.
Page 15
The Screen Adjustment

OSD V-Position Adjusts the OSD position up or down
Press “Up” to up, press “Down“ to down.
OSD Transparence Adjusts the OSD transparency.
Press “Up” or “Down“ to adjust the parameter.
Off Time Adjusts the OSD exit time.
Press “Up” or “Down“ to adjust the parameter.
◆OSD For Video input
Press “Up” or “Down” to locate the item you desire to change, then press “Select” to
make the adjustment, press “Menu” again to go back to previous menu.
Page 16
The Screen Adjustment

Image Adjust This item can adjust video color as Brightness, Contrast,
Saturation Hue, Sharpness.
Audio This item can adjust audio function. As Volume, Mute, Treble,
All functions adjustment are same as PC mode
Page 17
The Screen Adjustment
Base, Balance.
System This item can Select Source input (PC, AV, S-Video, TV,
Component.) and Recall System data.
OSD This item can control OSD window function. As OSD
H-Position, OSD V-Position, OSD Transparence and OSD Off
time.

. Remote Control Function List
1. POWER
Power On/Off.
2. Input Source Select
TV: Select TV video input.
PC: Select PC-VGA input.
AV: Select AV video input.
S-VIDEO: Select S-VIDEO video input.
COMP.: Select Component video input
14 3. MEMORY
Channel memories or erase.
13 4. OSD Control
MENU: Turns On/Off the On-Screen Display.
12 1SELECT: Execute your selection.
“-“: Select the Item or decrease the value.
“+”: Select the Item or increase the value.
5. MUTE
Sound On or Off.
6. DISPLAY
11 2Shown a channel number in the screen.
7. CHANNEL
3Change the channel.
15 8. VOLUME
17 Adjust the volume.
16 9. JUMP
4Return to last the TV channel.
10. MTS
Multi-Channel Television sound select.
10 5Stereo→SAP→Mono
11. Digital key from 0 to 9 and above 100.
96Use to select a TV channel.
12. SCAN
Auto scan TV program.
13.AIR/CATV
Select the input source from Cable TV or
8 7 AntennaTV.
14. SLEEP
Setup the sleep timer.
15. PIP
Enable the PIP function
16. Source
Select the Sub. source of Video
17.Audio
Select the PC/Video audio source
Page 18
The Screen Adjustment

Page 19
Quick Installation & Troubleshooting Tips
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Plug one terminal of the VGA cable to the signal connector at the rear of the LCD Monitor.
Plug theother terminal of the VGA cable to thesignal connector at the rearof PC.
PlugAdapter output to the jack at therear of LCD Monitor.
Plug thePower cord to the Adapter.
Connectthe Power cord to power outlet.
Turn on the LCD Monitor and PC.
You canalso plugin RCA jack to connect your video source like DVD or VCR.
You canview video over PC by pressing "PIP" button on remote controller.
Please followthefollowingdescriptionsstepbystep.
(The7diagrams canalsobeyourreferences):
Step 1 Step 2 Step 3 Step 4 Step5Step 6 Step 7
In the event that you experience trouble with your Display, check the following items before
contacting the dealer from whom the Display was purchased. The most common problems
usually involve an incorrectly an incorrect connection from the Video Card to the Display. We
recommend that you also consult your Video Card User’s manual during the Troubleshooting
Procedure. Do not exceed the maximum refresh rate recommended for the display.
Problem Troubleshooting Tip
No image on display
screen 1. Check that power cord of the Computer has been connected securely into wall outlet or grounded
extension cable or strip.
2. Check that power switch of the Display has been
pressed and LED on the front of Display is lit.
3. Check that Video (Signal) cable from the Display
has been securely and correctly connected.
4. Check that Video Card is firmly seated in card slot
of Computer motherboard.
5. Check that the video input from the Video Card
falls within the timing range.
Abnormal image 1. Check that the video input from the Video Card
falls within the timing range.
2. Check that Video (Signal) Cable from the Display
has been securely and correctly connected to the
Video Connector at the rear side of the Computer.
Colors of image on
screen are abnormal
1. Check that Video (Signal) Cable from the displays
has been securely and correctly connected to the
15-pin Video Connector at the rear side of the
computer.
Disturbances on
Screen 1. OSD adjustment is incorrect. Please consult section for OSD screen adjustment procedures.
※Please contact your local authorized distributors /retailers if you run into other unsolved problems.

Page 20
Specification
Model No. LCD-2001VB
Display Area 408 (H) x 306 (V) mm
LCD Display 20.1"TFT active matrix
Display Colors 16.7M colors
Luminance 1000 cd/m2 (typ.)
Contrast Ratio 500:1 (typ.)
Resolution 800 x 600 (SVGA)
Pixel Arrangement RGB (Red, Green, Blue) vertical stripe
Pixel Pitch 0.51 (H) x 0.51 (V) mm
Color Gamut At LCD panel center
60% (typ.) [against NTSC color space]
Ton (black 10% white 90%)
Response Time 16 ms (Typ.)
Sync TTL Positive or Negative
Signal Connector 15 Pin D-sub
F/R Control Button Power Switch, Menu, Select (+,-), Auto
OSD Menu Brightness, Contrast, H/V Position, Color, Phase,
Clock, Language, Management
Power
Consumption At maximum luminance and checkered flag pattern 80W (Max)
Module Size 507(H) x 413.6 (V) x 63.1 (D) mm
Weight (Net) 8.08kg (typ.)
※Specifications subject to change without notice.
Viewing Angle At the contrast ratio 10:1
-Horizontal: Left side 85° (typ.), Right side 85° (typ.)
-Vertical: Up side 85°(typ.), Down side 80° (typ.)