Toto NEOREST TBXM1B V201 User manual

Installation Manual
Bathtub Faucet
Model TBXM1B V201
For best results, be sure to follow the installation intructions and use the product only as described in the manual.
Important Safeguards…………… 1 2
2Replacement Parts………………………
3Before installation………………………
3Specifications …………………………
4Rough-In…………………………………
Installation procedure…………… 5 9
Trial Run and Temperature Adjustment …10 13
14Check the product………………………

1
Less than
85
Close Stop Valve
Read the “Important Safeguards” section thoroughly before installing the product.Read the “Important Safeguards” section thoroughly before installing the product.
The following symbols indicate safe and proper use of the product.
Failure to observe them may result in injury or property damage.
The symbols and their meanings are as follows.
The following table demonstrates the use of safety symbols in this manual.
Symbol Meaning
Warning
Caution
Failure to observe this symbol may result in serious injury or death.
Failure to observe this symbol may result in injury or property damage.
Warning
Do Not
Absolutely Do NOT.
Do not disassemble!
Mandatory!
Important Safeguards (For your safety please follow the instructions below)
Do not disassemble or modify the item in any way
not described in this manual.
If the system is broken, property damage, scalding and other
injuries are likely to occur.
When cleaning the filter, do not loosen the cover first but
loosen it after closing the water shutoff valve.
Also, make sure that the filter at hot water side is not so hot.
Hot water of high temperature may come out to scald you or give
damage to your property by water leakage.
Mandatory
Do not
disassemble
Do not use hot water that is 85 or hotter.
If water hotter than 85 is used, faucet life will be reduced, if
damage occurs, property damage,scalding and other injures may
occur due to water leakage.
To demonstrate full performance of the product, it is recommended
to set the water supply temperature of the water heater at 60 .

2
Installation
manual
Label of use method
Operation
manual
Give these to customer!
Caution
Do Not
Parts may be broken and water may leak to give damage to your
property by wetting household goods.
Do not install the product outdoors or in a place
where freeze likely occurs.
If the product is broken, property damamge, scalding and other
injuries may occur due to water leakage.
Do not strike violently.
Freezing
Replacement Parts
Check that you have the following parts.
Read the “Important Safeguards” section thoroughly before installing the product.

3
Before installation
Specifications
Part No.
Suitable water quality
Usage
Supply voltage
TBXM1B V201
24.5L/min 0.3MPa
8L/min 10L/min 0.3MPa
Potable water from riyer or well
Suitable ambient temperature 1 42
Hot water supply temperature 60 85
AC 100 240V (50/60Hz)
1.0MPa (hydrostatic pressure)
0.2 0.3MPa
0.2 0.3MPa
For use in public and general family bath room
max
Recommended
0.15MPa (flow pressure)min
Flow rate
Operating
pressure
range
spout
Water inlet
9W
5.5W
G1/2
Power
consumption
operating
standby mode
shower
In use of pressure
reducing valve
Set the hot water supply temperature at least 10°C higher than the temperature of the
water to be used.
If flow pressure exceeds 0.5 MPa, a pressure reducing valve must be installed.
Make sure the water pressure is higher, or matches hot water output pressure.

4
Rough-In
(mm)
85
95.5120.5
205
44
46251
50
-
64
5-25
109
274
133.5
53 45

5
Installation procedureInstallation procedure
1Remove the protective covers (A).
2Fasten the shower hanger (C) to the base plate (D).
After fastening the shower hanger, remove the cardboard (E).
Make sure the connectors does not drop below the frame (B).
9
8
2 3 4 5
3.0mm
B
A
D
C
E
6

Installation procedure
6
3.0mm
F
D
3Join the connectors according to color.
4Fasten the base plate (D).
To prevent bolt (F) burn-in, do not use an impact wrench.
To prevent warping, tighten tentatively before tightening firmly.

7
G
H
I
5Install the shower base (G) and the cover plate (H).
6Connect the shower head (I).

8
2.5mm
2.5mm
38
38
1
2
3
M
J
L
K
8Connect the handle (J).
If it is necessary to replace the spindle (K) and screw (L) because of the thickness of the tiles, please use the included
maintenance tools (M).
Be sure to check that the switch can be pressed smoothly after attaching .
5 10mm 10 15mm 15 20mm 20 25mm
7Check the thickness of the tiles.
Please make the choice of included replacement parts based on the thickness of the tiles.
The parts listed in the thick bordered table are included with this product.

9
3.0mm
70
9Connect the spout (N).
O
N
Depending on the thickness of the tiles, replace the adapter (O) if necessary.