Toto WENZAL TX445SWCV3Z User manual

SPECIFICATIONS
S060320-3N
TX445SWCV3Z
OPERATING CONDITIONS
Watersupply pressure : 0.05 ~ 0.75 MPa.
Ensure that water supply is clean( No Sand,Dirt, Etc.).
1.
2.
MAINTENANCE
TROUBLESHOOTING
7Shower
Flexible
Hose
Packing
Packing
5
43
INSTALLATION
1
Make sure the floor is flat
* Remove the cover after the
mortar has dry
2
6
* Cover
Mortar
Maximum
Mortar
Minimum
Mortar
Nut*
Flexible
Hose
Cover
Base
Drill
Hot Water
Supply *
Sleeve
Anchor
6 - Hole 8
Base
Cold Water
Supply *
Sc rew
* Pipe supplied by owner
ATTENTION
Flow Regulator Inside
(Don t remove)
PULL
PULL
2. CERAMIC
HEAD WORK
R6
"WENZAL" CROSS HANDLE FLOOR STANDING
BATH & SHOWER SET
* Tighten the nut
4.
Don t use abrasive cleaners or solvents on faucets and fittings.
Flow Regulator should not be remove because it could
damage the system
As the product model is constantly updated, the actual product
may not look the same as it shown in the diagram, but the
basic installation principles are the same.
The hot water supply side of the faucets is in a condition of
high temperature. Do not allow skin to contact with the
hardware surface directly. Otherwise, scalding may occur.
2.
1.
3.
All Finishes : Clean the finish with mild soapand warm water. Wipe
entire surface completely dry with clean soft cloth. Many cleaners
maycontainchemicals, such as ammonia, chlorine, toilet cleaneretc.
which could adversely affect the finish and are not recommended for
cleaning
PROBLEM CHECK
POINT SOLUTION
Clean1
2
Water leaks around the handle
Unsatisfactory spray
Tighten
1. NOZZLES
To Spout
To Shower
18°
236
856 0
-6
150
40
56+6
0
40
72
75.5
88
G½
18
60

SPECIFICATIONS
S060320-3N
TX445SWCV3Z
7Shower
Flexible
Hose
Packing
Packing
5
43
INSTALLATION
12
6
* Cover
Mortar
Maximum
Mortar
Minimum
Mortar
Nut*
Flexible
Hose
Cover
Base
Drill
Hot Water
Supply *
Sleeve
Anchor
6 - Hole 8
Base
Cold Water
Supply *
Sc rew
PULL
PULL
R6
"WENZAL" CROSS HANDLE FLOOR STANDING
BATH & SHOWER SET
PENYELESAIAN MASALAH
Pastikan lantainya rata
* Lepas cover setelah
mortar mengering
* Pipa disediakan oleh pemilik
PERHATIAN
* Kencangkan nut
KONDISI OPERASIONAL
PEMELIHARAAN
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih
(tidak ada pasir, kotoran dan lain lain)
To Spout
To Shower
18°
236
856 0
-6
150
40
56+6
0
40
72
75.5
88
G½
18
60
2. CERAMIC
HEAD WORK
1. NOZZLES
MASALAH POIN
PERIKSA SOLUSI
Bersihkan1
2
Air bocor disekitar handle
Pacaran tidak memuaskan
Kencangkan
Seluruh lapisan: Bersihkan lapisan akhir dengan sabun lembut dan
air hangat. Lap seluruh permukaanhinggabenar-benar kering
dengan kain lembut yang bersih. Kebanyakanbahan pembersih
mungkin mengandung bahan kimia, seperti amonia, klorin, pembersih
toilet,dll. yang dapat mempengaruhi hasil akhir dan tidak disarankan
untuk membersihkan
Jangan gunakan pembersih atau pelarut abrasif pada faucet dan
fitting.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidak samadengan gambar, tapiprinsip dasar
pemasangan adalah sama.
Sisi pasokanair panas pada kran faucet berada dalam kondisi
suhu tinggi. Janganbiarkankulit menyentuh permukaanbenda
secara langsung. Kalautidak, bisaterjadi kepanasan.
1.
2.
3.
4.
Flow Regulator Di dalam
(Jangan dilepas)