Town & Country Fireplaces TC30 Black Diamond User manual

5056.9030-A TC30 040216-12
Dimensions | Clearances | Venting
IMPORTANT
This booklet is intended as a basic specification
guide for architects, designers and builders.
Please refer to the Instruction Manual supplied
with the fireplace for detailed information regarding
installation and operation.
Product installation manuals can also be viewed at:
www.townandcountryfireplaces.com
FOR ARCHITECTS & DESIGNERS
TC30
SERIES D

2
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12 5056.9030-A_TC30.D
Fireplace Dimensions
Examples of Common Locations
40 5/16"
32 1/2"
32 1/16"
27 3/4"
28 3/8"
28 3/4"
44 1/4"
27 3/4
FRAME
LINTEL
Must allow for minimum 1/2 inch
gap for non-combustible board
and facing.
TC30.D Cad Drawing
Available at
www.townandcountryreplaces.com

3
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12
5056.9030-A_TC30.D
Mantel Clearance Chart
Minimum Clearances to Combustibles
* MANTEL CLEARANCE
A 9”
B 6”
C 3”
MANTEL CLEARANCE
CHART
** MANTEL DEPTH
D 12”
E 6 3/4”
F 1 1/2”
A
B
C
D
E
F
MANTEL
Adjacent wall or
mantel support
CEILING
Unit may be recessed up to 4 1/2” with
non-combustible masonary type material
Minimum Clearances:
Side standoffs .................................................. 0 in. (0 mm)
Back standoffs ................................................. 0 in. (0 mm)
Top standoffs.................................................... 0 in. (0 mm)
Bottom of appliance ......................................... 0 in. (0 mm)
Adjacent side wall............................................. 4 in. (102 mm)
Ceiling to appliance .......................................... 24 in. (610 mm)
*Mantel to appliance.......................................... See mantle clearance
.................................................................... chart above
**Maximum Mantel extension............................. See mantle clearance
..................................................................... chart above
.....................................................................
Mantel support ................................................. 4 in. (102 mm)
Vertical vent pipe ............................................. 1 3/4" in.(45 mm)
Horizontal Vent pipe (Top, sides and bottom) .... 1 3/4" in.(45 mm)
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS
AREA
NON-COMBUSTBLE
FINISH MATERIAL
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE
MATERIAL, ELECTRICAL WIRING OR GAS
PLUMBING IN THIS AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS
STANDOFFS
STEEL FRAMING
FIREPLACE
FRONT
TOP OF LINTEL BAR

4
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12 5056.9030-A_TC30.D
47 3/8”
40 3/8”
Steel Stud Framing Kit Dimensions Kit
Minimum Combustible Framing Dimensions
NON-COMBUSTIBLE materials
must extend 12” above and 5 7/8”
to the sides of the framing edges.
NON-COMBUSTIBLE BOARD NOT
INCLUDED.
NON-COMBUSTIBLE BOARD
All other framing can be done with
conventional lumber
Non-combustible
Board Detail
12”
5 7/8”
47 3/8"
47 3/8"
61 7/8"
61 7/8"
Minimum
86 1/8"
FRAME
LINTEL
*
Range from front of supplied frame to the back
side of rear standoff is from 22 3/4” to 24 1/8”
*
Framing kit is supplied
with unit with Fireplace
Must allow for
minimum 1/2 inch
gap for non-combustible
board and facing
NOTE: Fireplace should be in its final location before framing.
NOTE: Combustible framing must allow for sheetrock installation.

5
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12
5056.9030-A_TC30.D
Proflame 2 Control System
Hearth Extension
Recessed Installation
Up to 40 Feet
ON
REMOTE
OFF
PROGRAM
TOWN & COUNTRY
LUXURY FIREPLACES
Caution: This fireplace may be recessed up to a maxi-
mum depth of 4 1/2”. This recess must be constructed
from non-combustible material. The space between the
outside framing edge and the firebox must be completely
free of any obstructions or debris, and the window, with
trim fitted, must be able to move freely.
No building material is permitted to protrude past the
framing edges attached to the fireplace under ANY
circumstance.
Town and Country D Series fireplaces use the SIT
Proflame 2 control system.
This includes an elegant hand-held remote control
transmitter with an easy to read LCD display.
The fireplace also comes with a wall-mounted control
switch which allows for simple ON/OFF operation, or
can be linked with the hand-held remote control unit.
This switch has a battery powered back-up system
which allows operation during power outages. The
wall-mounted switch easily connects to any customer
supplied Home Automation System.
Caution: While a hearth extension is not required and
combustible flooring materials may be brought directly up
to the fireplace, many materials (such as wood flooring)
may not tolerate the radiant heat from this fireplace,
resulting in discoloration, shrinking and cracking. For this
reason, we suggest a non-combustible hearth that is no
more than 1” above the bottom of the fireplace. If material
is thicker, fireplace must be raised accordingly.
Caution: Hearth extensions thicker than 1” will
interfere with the window frame when opening.
LINTEL
Surface of hearth extension
may not be higher than the
oor of the lintel and may not
be more than 1 inch above
the bottom of the replace.

6
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12 5056.9030-A_TC30.D
Direct Vent Wall Installation
* Minimum height 52 7/16 from the floor to center of the
opening with a maximum horizontal run of 34 5/16" using
a 24" pipe. The height will need to be increased with a
longer horizontal run.
* 52 7/16
HORIZONTAL
TERMINAL
14 1/2" FRAMED
OPENING
WALL SHIELD
THIMBLE
ELBOW
MIN 12" VENT PIPE
MIN 24"
VENT PIPE
Direct Vent
Roof Installation

7
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12
5056.9030-A_TC30.D
Wall Termination Venting Chart
** All dimensions are approximate. Both rise and run may vary with
different combinations of pipe.
12" Pipe length
minimum
A
Minimum rise
B
Pipe length
C
Maximum run
D
Pipe length
Max.
52 7/16” 1 x 12” 34 5/16" 1 x 24"
64 7/16” 1 x 24” 46 5/16" 1 x 24" + 1 x12"
74 11/16” 1 x 24"+ 1 x 12” 166 5/16" 3 x 48" + 1 x12"
80 11/16” 1 x 24"+ 1 x 18” 226 5/16" 4 x48” + 1 x 24”
87 11/16” 1 x 48” 250 5/16” 5 x 48"
For other rise/run combinations see chart below
**
NOTE: The vent must not exceed a total length of 68 feet. Any com-
bination of rise and run may be used but must be constrained to the
boundaries of this chart. A total of 3 90° elbows or combination of other
elbows equalling 90° can be used without reducing horizontal run. For
each additional 90° elbow, or an equal combination of elbows, reduce
horizontal vent run by 2 feet. Ensure vent pipe is properly supported. A
minimum of 1 support every 4’ must be used.
TC30.D Cad Drawing
Available at
www.townandcountryreplaces.com

8
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12 5056.9030-A_TC30.D
Roof Termination Venting Chart
NOTE: The vent must not exceed a total length of 68 feet. Any combination of
rise and run may be used but must be constrained to the boundaries of this chart.
A total of four 90° elbows, or combination of other elbows equalling 90°, can be
used without reducing horizontal run. For each additional 90° elbow, or an equal
combination of elbows, reduce horizontal vent run by 2 feet. Ensure vent pipe is
properly supported. A minimum of 1 support every 4’ must be used.
** All dimensions are approximate. Both rise and run may vary
with different combinations of pipe.
12" Pipe
length
minimum
A
Minimum rise
B
Pipe length
C
Maximum run
D
Pipe length
Maximum
52 7/16" 1 x 12” 41" 1 x 24"
64 7/16” 1 x 24” 51 1/4" 1 x 24" + 1 x 12"
74 11/16” 1 x 24” + 1 x 12" 167 3/4" 3 x 48" + 1 x 12"
80 11/16” 1 x 24” + 1 x 18" 226" 4 x 48" + 1 x 24"
87 11/16” 1 x 48" 250" 5 x 48"
For other rise/run combinations see chart below
**
TC30.D Cad Drawing
Available at
www.townandcountryreplaces.com

9
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12
5056.9030-A_TC30.D
M
K
I
A
V
G
G
H
A
J
V
G
A
B
C
A
V
V
A
V
B
F
B
L
V
E
V
V
V
D
B
B
Vent Terminal Clearance
Vent Terminal Minimum Clearances
Minimum clearances to the vent terminal must be maintained
as shown (See illustration to right & below). Measure
clearances to the nearest edge of termination hood.
(See pitch table below).
NOTE: Vent terminal must not be recessed
NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE
DIFFERENT CLEARANCES.
Terminal to sloped Roof Pitch Table
(minimum)
ft m
Flat to 6/12 1.00 0.30
Over 6/12 to 7/12 1.25 0.38
Over 7/12 to 8/12 1.50 0.46
Over 8/12 to 9/12 2.00 0.61
Over 9/12 to 10/12 2.50 0.76
Over 10/12 to 11/12 3.25 0.99
Over 11/12 to 12/12 4.00 1.22
VENT TERMINAL MINIMUM CLEARANCES
TO ADJACENT STRUCTURES
A= *12 inches (30 cm) min. Clearances above grade, veranda, porch, deck, or balcony
B= *12 inches (30 cm) min. Clearance to window or door that may be opened
C= 12 inches (30 cm) min. Clearance to permanently closed window recommended to prevent condensation on window
D= 30 inches (76 cm) min. Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (60 cm) from the
edge of the terminal
E= 30 inches (76 cm) min. Clearance to unventilated soffit
F= 6 inches (15 cm) min. Clearance to outside corner
G= 6 inches (15 cm) min. Clearance to inside corner
H= 3 feet (90 cm) min. *Not to be installed above a meter/regulator assembly within 3 feet (90 cm) horizontally from the center-line of the
regulator
I= *6 feet (1.8 m) min. Clearance to service regulator vent outlet
J= *12 inches (30 cm) min. Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance
K= *6 feet (1.8 m) min. Clearance to a mechanical air supply inlet
L= *7 feet (2.1 m) min. ^ Clearance above paved side-walk or a paved driveway located on public property
M= **30 inches (76 cm) min Clearance under veranda, porch, deck, or balcony
^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings*
** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the floor*
* as specified in CAN/CSA B149.1 Installation Codes, Note: local Codes or Regulation may require different clearances
* for U.S.A. Installations follow the current National Fuel Gas Code, NFPA54/ANSI Z223.1
AIR SUPPLY INLET
VENT TERMINAL GAS METER
AREA WHERE TERMINAL
IS NOT PERMITTED
FIXED
CLOSED
FIXED
CLOSED OPEN-
ABLE
OPEN-
ABLE
36"
See Roof
pitch table
48"
ADJACENT
24"
(91.5 cm)
(61 cm)
(122 cm)
STRUCTURES
OR FENCE

10
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12 5056.9030-A_TC30.D
Up to 66 feet
of vertical run
Up to 110 feet of run
plus six 90º elbows
Up to 3 feet below unit
Optional Power Vent
Power Vent Terminals
Direct Vent Terminals
Reach almost any room or commercial setting.
Optional Power Venting allows runs up to 110’ to
an outside wall or roof surface (maximum 66’ of
vertical run). Vent horizontally or vertically with up
to six 90-degree elbows, including runs up to 3’
below the fireplace.
The premium Power Vent fan runs quietly outside,
at the exterior terminal.
Roof Termination
Flush Mount termination
Stainless Steel Standard Venting
Termination for Condo Installation
Standard Venting
Wall Termination
Standard Venting
Roof Termination
TC30.D Cad Drawing
Available at
www.townandcountryreplaces.com

11
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
040216-12
5056.9030-A_TC30.D

FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
For personal service pertaining to specific projects, contact:
Town & Country Architect Resource Planner
[e-mail]
www.townandcountryfireplaces.com
Phone: [phone]
2975 Allenby Road, Duncan, BC Canada V9L 6V8
© 2016 Copyright Pacic Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.