Town & Country Fireplaces TC54 SERIES DMODULAR User instructions

TC54.D 280915-12
IMPORTANT
This booklet is intended as a basic specication guide
for architects, designers and builders. Please refer to the
Instruction Manual supplied with the replace for detailed
information regarding installation and operation.
Product installation manuals can also be viewed at:
www.townandcountryreplaces.com
5056.9054-A
FOR ARCHITECTS & DESIGNERS
TC54
SERIES D Dimensions | Clearances | Venting

2
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-12 5056.9054-A_TC54D
Fireplace Dimensions
54 5/16"
63 7/8"
34 1/8"
48 1/8"44 1/2"
62 9/16"
35 5/8"
34 1/8"
Examples of Common Locations
FRAMING
LINTEL
Must allow for minimum 1/2 inch
gap for non-combustibel board
and facing TC54D Cad Drawing
Available at
www.townandcountryreplaces.com
See “Minimum Combustible Framing Dimensions”
section on page 6 for precise framing dimensions.
For diagonal installation, corner
of fireplace should maintain
standoff distance of 2” to
combustible framing material.
For diagonal installation, corner
of control box is permitted to
make contact with combustible
framing material.

3
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-125056.9054-A_TC54D
5056.9054-A_TC54D
Direct Vent Roof Installation
20'
10'
40'
MAX.
48'
4' MAX.
'
5
NOTE: A vertically vented TC54
cannot be power-vented.
Minimum total vent height for
propane: 20 feet.
Minimum total vent height for
natural gas: 10 feet.
Minimum 5’ of vertical vent
required before 1st elbow.
16 1/2”
9”
Vertical termination cap
dimensions
Termination cap shown without
vertical vent pipe. For vent terminal
minimum clearances, see Roof Pitch
Table and Vent Terminal Minimum
Clearances Table - both on page 8.

4
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-12 5056.9054-A_TC54D
Wall Termination Venting
TC54D Cad Drawing
Available at
www.townandcountryreplaces.com
This unit can be vented horizontally (wall termination) ONLY with an approved High Capacity
Power Vent Kit (TCVT.PVAX2) using TC 8x11 Vent Pipe.
Up to 66 feet of run
plus six 90º elbows
Up to 3 feet below unit
Power vent
terminal
Power vent
terminal
Finished exterior wall
Power vent terminal
Blower outlets
Maximum vent length is 66 ft plus six 90 degree elbow or combination of other elbows equaling 90 degrees.
Minimum vent length is 10 ft plus one 90 degree elbow. The vent can be installed with any combination of
rise and run between the above figures including 3ft below the unit.
The premium Power Vent fan runs quietly outside, at the exterior terminal.
29 5/8”
16 3/4”
19 1/8”
Power vent dimensions

5
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-125056.9054-A_TC54D
5056.9054-A_TC54D
Mantel Clearance Chart
Minimum Clearances to Combustibles
* MANTEL CLEARANCE
A 17”
B 15”
C 12”
MANTEL CLEARANCE
CHART
** MANTEL DEPTH
D 12”
E 6”
F 1”
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS
AREA
NON-COMBUSTBLE
FINISH MATERIAL
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE
MATERIAL, ELECTRICAL WIRING OR GAS
PLUMBING IN THIS AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS
STANDOFFS
STEEL FRAMING
FIREPLACE
FRONT
TOP OF LINTEL BAR
A
B
C
D
E
F
Unit may be recessed up to 4 1/2” with
non-combustible masonary type material
MANTEL
CEILING
24”
4”
ADJACENT WALL
OR MANTEL SUPPORT
AN 18" DEEP, 2" THICK, NON-COMBUSTIBLE
HEARTH MUST BE PLACED IN FRONT OF
THE FULL WIDTH OF THE GLASS
*
**
43 5/8”
Minimum Clearances:
Side standoffs .................................................. 0 in. (0 mm)
Back standoffs ................................................. 0 in. (0 mm)
Top standoffs.................................................... 0 in. (0 mm)
Bottom of appliance ......................................... 0 in. (0 mm)
Adjacent side wall............................................. 4 in. (102 mm)
Ceiling to appliance .......................................... 24 in. (610 mm)
*Mantel to appliance.......................................... See mantle clearance
.................................................................... chart above
**Maximum Mantel extension............................. See mantle clearance
..................................................................... chart above
.....................................................................
Mantel support ................................................. 4 in. (102 mm)
Vertical vent pipe ............................................. 1 3/4" in.(45 mm)
Horizontal Vent pipe (Top, sides and bottom) .... 1 3/4" in.(45 mm)

6
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-12 5056.9054-A_TC54D
5 7/8
18 3/4
63 5/8"
81 1/8"
26 5/8"
81 1/8"
37 11/16"
1/2"
63 5/8"
114 11/16"
RANGE
32 13/16"
to
34 9/16"
RANGE
34 13/16"
to
36 5/16"
RANGE
1/32"
to
3 1/2"
14 5/8"
FRAMING
LINTEL
63 5/8"
63 7/8"
Steel Stud Framing Kit Dimensions Kit
Minimum Combustible Framing Dimensions
NON-COMBUSTIBLE materials
must extend a minimum of 18 3/4”
above and 5 7/8” to the sides of
the framing edges.
NON-COMBUSTIBLE board not
included.
NON-COMBUSTIBLE BOARD
All other framing can be done with
conventional lumber
NOTE: Fireplace should be in its final location before framing.
NOTE: Combustible framing must allow for sheetrock installation.
Non-combustible
Board Detail
Framing kit is supplied
with unit with Fireplace
Must allow for
minimum 1/2 inch
gap for non-combustible
board and facing

7
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-125056.9054-A_TC54D
5056.9054-A_TC54D
Hearth extension
2” thick minimum
18” wide minimum
Length of glass
Bottom of replace
1” max above bottom of replace
Lintel
Proflame 2 Control System
Hearth Extension
Recessed Installation
Up to 40 Feet
Caution: A minimum 2” thick non-combustible hearth
extension extending 18” in front of this fireplace must be
fitted if a combustible sub floor extends in front of the
fireplace. To ensure that the hearth does not interfere with
the window frame the fireplace must be raised to ensure
that the hearth extension is no more than 1” above the
bottom of the fireplace.
The fireplace can be raised using combustible or non-
combustible materials ensuring that it is fully supported
along the full width and depth of the fireplace.
ON
REMOTE
OFF
PROGRAM
TOWN & COUNTRY
LUXURY FIREPLACES
Caution: This fireplace may be recessed up to a
maximum depth of 4 1/2”. This recess must be
constructed from non-combustible material. The space
between the outside lintels and the firebox must be
completely free of any debris and the window, with trim
fitted, must be able to move freely.
Finishing material may not protrude past framing flanges
under ANY circumstance.
Town and Country D Series fireplaces use the SIT
Proflame 2 control system.
This includes an elegant hand-held remote control
transmitter with an easy to read LCD display.
The fireplace also comes with a wall-mounted control switch
which allows for simple ON/OFF operation, or can be linked
with the hand-held remote control unit. This switch has a
battery powered back-up system which allows operation
during power outages. The wall-mounted switch easily
connects to any customer supplied Home Automation
System.

8
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-12 5056.9054-A_TC54D
Vent Terminal Minimum Clearances
A= *12 inches (30 cm) min. Clearances above grade, veranda, porch, deck, or balcony
B= *12 inches (30 cm) min. Clearance to window or door that may be opened
C= 12 inches (30 cm) min. Clearance to permanently closed window recommended to prevent condensation on window
D= 30 inches (76 cm) min. Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (60 cm) from the
edge of the terminal
E= 30 inches (76 cm) min. Clearance to unventilated soffit
F= 6 inches (15 cm) min. Clearance to outside corner
G= 6 inches (15 cm) min. Clearance to inside corner
H= 3 feet (90 cm) min. *Not to be installed above a meter/regulator assembly within 3 feet (90 cm) horizontally from the center-line of the
regulator
I= *6 feet (1.8 m) min. Clearance to service regulator vent outlet
J= *12 inches (30 cm) min. Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance
K= *6 feet (1.8 m) min. Clearance to a mechanical air supply inlet
L= *7 feet (2.1 m) min. ^ Clearance above paved side-walk or a paved driveway located on public property
M= **30 inches (76 cm) min Clearance under veranda, porch, deck, or balcony
^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings*
** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the floor*
* as specified in CAN/CSA B149.1 Installation Codes, Note: local Codes or Regulation may require different clearances
* for U.S.A. Installations follow the current National Fuel Gas Code, NFPA54/ANSI Z223.1
AIR SUPPLY INLET
VENT TERMINAL GAS METER
AREA WHERE TERMINAL
IS NOT PERMITTED
FIXED
CLOSED
FIXED
CLOSED OPEN-
ABLE
OPEN-
ABLE
M
K
I
A
V
G
G
H
A
J
V
G
A
B
C
A
V
V
A
V
B
F
B
L
V
E
V
V
V
D
B
B
Vent Terminal Clearance
Minimum clearances to the vent terminal must be maintained
as shown (See illustration to right & below). Measure clear-
ances to the nearest edge of termination hood. (See pitch
table below).
NOTE: Vent terminal must not be recessed
NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE
DIFFERENT CLEARANCES.
Terminal to sloped Roof Pitch Table
(minimum)
ft m
Flat to 6/12 1.00 0.30
Over 6/12 to 7/12 1.25 0.38
Over 7/12 to 8/12 1.50 0.46
Over 8/12 to 9/12 2.00 0.61
Over 9/12 to 10/12 2.50 0.76
Over 10/12 to 11/12 3.25 0.99
Over 11/12 to 12/12 4.00 1.22
VENT TERMINAL MINIMUM CLEARANCES
TO ADJACENT STRUCTURES
36"
See Roof
pitch table
48"
ADJACENT
24"
(91.5 cm)
(61 cm)
(122 cm)
STRUCTURES
OR FENCE
Roof Pitch Table
Vent Terminal Minimum Clearances Table

9
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-125056.9054-A_TC54D
5056.9054-A_TC54D

10
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-12 5056.9054-A_TC54D

11
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
280915-125056.9054-A_TC54D
5056.9054-A_TC54D

FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
For personal service pertaining to specific projects, contact:
Town & Country Architect Resource Planner
[e-mail]
www.townandcountryfireplaces.com
Phone: [phone]
2975 Allenby Road, Duncan, BC Canada V9L 6V8
© 2015 Copyright Pacific Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.