TownSteel TSF-300A User manual

B A
TSF-300A/300/120
CENTER HUNG PACKAGES
INSTALLATION INSTRUCTIONS
INSERT THE SPINDLE INTO
THE FLOOR HINGE.
14
5
2
3
PUT THE WASHER FIRST AND FIT END
SQUARED & ANGLED PART OF SPINDLE INTO
HOLLOW AREA AND TIGHTEN IT BY USE OF
SPINDLE SCREW READY ALREADY.
TURN THE ADJUSTMENT SCREW IN A
ANTICLOCKWISE AND RELEASE PIVOT PIN .
INSTALL THE PIVOT INTO UPPER PART OF DOOR
FRAME. AND COVER IT.
INSERT PIVOT CHANNEL INTO TOP OF DOOR,
INSTALL BEARING INSERT INTO PIVOT CHANNEL.
TIGHTEN UP THE ADJUSTMENT SCREW ALMOST
AND CONTROL THE CENTER POINT OF PIVOT.
FIX THE BEARING TO THE VERY PROPER
LOCATION.
INSTALL IN THE CENTER OF THE FLOOR HINGE
CEMENT BOX AND TIGHTEN THE FASTENING
SCREWS.
MAKE CEMENT BOX AND PUT THE FLOOR HINGE
IN THE CEMENT BOX.
THE UPPER PART OF THE CEMENT BOX SHOULD
BE ON THE LEVEL WITH THE FLOOR SURFACE.
THE CEMENT BOX SHOULD BE A LEVEL SURFACE.
ADDITIONALLY THE CENTER OF SPINDLE HAS TO BE
POSITED CORRECTLY.
FULFILL GROUT AROUND CEMENT BOX.
(LH Door) (RH Door)
CAUTION -PUT THE WASHER FIRST.
SPINDLE
SCREW
SPINDLE
WASHER
ADJUSTMENT SCREW
PIVOT
COVER PLATE
FOR SINGLE ACTION
OFFSET 3 °.
FOR DOUBLE ACTION
STANDARD TYPE SPINDLE
FLOOR FINISHED
BEARING INSERT
ADJUSTMENT
SCREW
POIVOT CHANNEL
TOP PIVOT
CAUTION: 1.Dimension indicated is not a real size. 2.Dimensions are in mm. 3.All reinforcement accessories for bottom arm should be prepared by user.
34
25
18
32
Min 34
7
5
25
5
100
169
126
13
70
1479
70
45 25
DOOR GAP 3
12.5
12.5
135
25
90
12
12
Holes for pivot insert x 4 ea Use
Ø
5.1 drill for M6 X 1.0 mech. Screw.
Holes x 5 ea Use Ø 4.3 drill for M5 x 0.8 mech. Screw.
REAR view
Door frame position
Front view
SIDE view
PLANE VIEW
R65
DOOR area.
COVER PLATE
C/L
BOTTOM ARM
CAUTION: 1,Dimension indicated is not a real size. 2,Dimensions are in mm. 3,All reinforcement accessories for bottom arm should be prepared by user.
Holes x 5 ea Use Ø4.3 drill for M5 x 0.8 mech. Screw.
2024
70
36
DOOR GAP 3
Floor area nished
5940 52 52 52
201
Front view Rear View
R65
C/L
FASTENING SCREWS

B A
TSF-300A/300/120
OFFSET HUNG PACKAGES
INSTALLATION INSTRUCTIONS
INSERT THE SPINDLE INTO
THE FLOOR HINGE.
14
5
2
3
PUT THE WASHER FIRST AND FIT END
SQUARED & ANGLED PART OF SPINDLE INTO
HOLLOW AREA AND TIGHTEN IT BY USE OF
SPINDLE SCREW READY ALREADY.
INSTALL TOP PIVOT
REMOVE CAP, PIVOT PIN
AND THEN INSTALL TOP PIVOT.
INSTALL BOTTOM ARM.
INSTALL IN THE CENTER OF THE FLOOR HINGE
CEMENT BOX AND TIGHTEN THE FASTENING
SCREWS.
MAKE CEMENT BOX AND PUT THE FLOOR HINGE
IN THE CEMENT BOX.
THE UPPER PART OF THE CEMENT BOX SHOULD
BE ON THE LEVEL WITH THE FLOOR SURFACE.
THE CEMENT BOX SHOULD BE A LEVEL SURFACE.
ADDITIONALLY THE CENTER OF SPINDLE HAS TO BE
POSITED CORRECTLY.
FULFILL GROUT AROUND CEMENT BOX.
(LH Door) (RH Door)
CAUTION -PUT THE WASHER FIRST.
SPINDLE
SCREW
SPINDLE
WASHER
FOR SINGLE ACTION
OFFSET 3 °.
FOR DOUBLE ACTION
STANDARD TYPE SPINDLE
FLOOR FINISHED
CAUTION: 1,Dimension indicated is not a real size. 2,Dimensions are in mm. 3,All reinforcement accessories for bottom arm should be prepared by user.
FASTENING SCREWS
BOTTOM OF DOOR
OFFSET ART
FRAME POSITION
DOOR POSITION
PIVOT PIN
CAP
TOP PIVOT OFFSET ARM
FRONT VIEW
FRONT VIEW
BACK VIEW
BACK VIEW
CAUTION: 1.Dimension indicated is not a real size. 2.Dimensions are in mm. 3.All reinforcement accessories for bottom arm should be prepared by user.

INSTALL DOOR ADJUSTMENT THE GAP BETWEEN DOOR
AND FLOOR.(IF NEEDED)
67
WITH DOOR PARALLEL TO FRAME, PLACE BOTTOM
ARM ONTO CLOSER SPINDLE. ALIGN DOOR AND
FRAME POSTION OF TOP PIVOT. INSTALL PIVOT PIN
AND CAP. INSTALL COVER OVER OFFSET ARM.
THE FLOOR HINGES HEIGHT CAN BE UP AB. 4MM
INTO THE CEMENT BOX.
RELEASE THE FASTENING SCREW “A” AND TURN
THE HEIGHT ADJUSTMENT SCREW “B” IN A
CLOCKWISE PROPERLY.
THE FLOOR HINGES SHOULD BE LEVEL OFF AND
TIGHTEN THE FASTENING SCREW ”A” AGAIN.
IN CASE BIGGER GAP IS NEEDED,MODIFY THE
SPINDLE SIZE PROPERLY.
INSTALLATION- COVER PLATE OR
DOORSILL.
11
Cement Case
PUT THE COVER PLATE PROPERLY TO THE DOOR
POST AS PIG. AND PUT THE TAB PROPERLY AS WELL.
DON’T FIX THE FLOOR HINGES TO THE DOORSILL,
IF THERE IS DOORSILL.
THE FLOOR HINGE CAN BE ADJUSTED IN THE
CEMENT BOX.
CAUTION:
1,Dimension indicated is not a real size.
2,Dimensions are in mm.
3,Upper of cement box should be on a level
with the floor surface finished.
4,Cement box should be a level surface and
parallel with door frame.
5,Cement box should be made after positing
the floor hinge in the center.
QTY
(4)
TAB
78
TSF-300A/300 (60)
TSF-120 (50)
(70)
(54
B A
± 3)
TSF-300A/300 (341)
TSF-120 (285)
C/L
C/L SIDE view
Cement Case
CLOSING SPEED CONTROL.
8
TSF-300A
VALVE “D”-TO CONTROL DOOR CLOSING SPEED
BETWEEN FULLY OPENED DOOR AND 80 °.
VALVE “E”- TO CONTROL DOOR CLOSING SPEED
BETWEEN 80 °AND 0 °.
DELAYING ACTION-TURN VALVE ‘D” IN A CLOCKWISE
AS MUCH AS YOU WANT.
HOLD OPEN-TURN VALVE ‘D” COMPLETELY IN A
CLOCKWISE.
DOOR CAN BE HOLD OPEN ALWAYS OVER 80 °.
HOLD OPEN POSITION HAS TO BE SETTLED AT
LESS 4 °.
VALVE “C” -START POSITION OF HOLD OPEN OR
DELAYING ACTION CAN BE CONTROLLED WITH
THIS. INCREASE SPEED ,TURN IN A CLOCKWISE
(MAX 105°.)
DECREASE SPEED,TURN IN A ANTICLOCKWISE
(MIN.75 °.)
TSF-300/120
VALVE “D”-TO CONTROL DOOR CLOSING SPEED
BETWEEN FULLY OPENED DOOR AND 15 °.
VALVE “E”- TO CONTROL DOOR CLOSING SPEED
BETWEEN 15 °AND 0 °
DELAYING ACTION-TURN VALVE ‘D” IN A CLOCKWISE
AS MUCH AS YOU WANT.
HOLD OPEN : 90° MECHANICAL HOLD OPEN.
-
+
ABAB
TSF-300A
TSF-300
TSF-120
A B A B
A
B
A
B
AB
B A
TSF-120
TSF-300
TSF-300/120
E
C
D
E
D
E
D
D
E
D
E